| Age | Commit message (Collapse) | Author |
|---|
|
As it is, an NVMe's built-in PERSTN pull-up fights against the
SoC's built-in pull-down which results in an undefined logic state
on the Samsung SSD 980 and likely others.
Fix that by forcing PERSTN low as early as possible, which is SPL.
Both Linux and U-Boot (via "pci enum") set the pin high later
as needed and the NVMe is detected fine.
Oscillocope shots ("x" means undefined logic state at around 1.5V):
Before:
3V3 ____|‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾
PERSTN ____xxxxxxxxxxxxxxx_|‾‾‾‾‾
PCICLK ____∿∿∿∿∿∿∿∿∿∿∿∿___∿∿∿∿∿∿∿
^U-Boot ^ Linux
After:
3V3 ____|‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾‾
PERSTN ____x_______________|‾‾‾‾‾
PCICLK ____∿∿∿∿∿∿∿∿∿∿∿∿___∿∿∿∿∿∿∿
^U-Boot ^ Linux
With this change, the power-up sequence conforms to PCIe specs,
except a remaining short PERSTN glitch. The glitch is about 400ms
long. It could be shortened by moving the logic to TPL, but
completely fixing it is only possible in hardware.
Signed-off-by: Jakob Unterwurzacher <[email protected]>
Reviewed-by: Quentin Schulz <[email protected]>
Link: https://patch.msgid.link/20260625-pub-jaguar-puma-ringneck-tiger-v2025-07_nvme-v2-1-c57bf1020d63@cherry.de
Signed-off-by: Quentin Schulz <[email protected]>
|
|
GPIO0_B7 is routed to TXI of the on-board CAN transceiver. The
line has a pull-down per SoC default.
This means the CAN transceiver transmits a dominant zero
and blocks the CAN bus until Linux boots and reconfigures the pin.
Let's switch to pull-up as soon as we can (i.e. in SPL).
This cuts down the "bus is blocked" time from 10 seconds to < 1 second.
Of course, to this needs CONFIG_SPL_BOARD_INIT, so enable it
the Jaguar defconfig.
Signed-off-by: Jakob Unterwurzacher <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
The build system uses HAVE_VENDOR_COMMON_LIB to automatically include
board/$(VENDOR)/common/Makefile, therefore let's use that to implicitly
include board/theobroma-systems/common/Makefile and compile the common.c
file when building proper.
Signed-off-by: Quentin Schulz <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
Use the new symbol to refer to any 'SPL' build, including TPL and VPL
Signed-off-by: Simon Glass <[email protected]>
|
|
No meaningful changes were made to this SoM since February 2021. Nobody
from Theobroma has booted anything recent on that product since July
2021 at the latest. The product isn't available to buy anymore and
disappeared from our website.
This product is therefore unmaintained and it would be disingenuous to
say the opposite, so drop support for RK3368 Lion.
If you're a user of Lion, feel free to revert this patch or contact our
sales/support department.
Signed-off-by: Quentin Schulz <[email protected]>
Acked-by: Heiko Stuebner <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
It turns out only Puma had a working git:// URL. Though that is now
fixed, having HTTPS URLs make it easier to directly reach our cgit
webserver to check what's up without having to change the URL manually.
Depending on your terminal settings, this also makes it possible to
open the link from it.
Signed-off-by: Quentin Schulz <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
The RK3588-Q7 SoM is a Qseven-compatible (70mm x 70mm, MXM-230
connector) system-on-module from Theobroma Systems, featuring the
Rockchip RK3588.
It provides the following feature set:
* up to 16GB LPDDR4x
* on-module eMMC
* SD card (on a baseboard) via edge connector
* Gigabit Ethernet with on-module GbE PHY
* HDMI/eDP
* MIPI-DSI
* 4x MIPI-CSI (3x on FPC connectors, 1x over Q7)
* HDMI input over FPC connector
* CAN
* USB
- 1x USB 3.0 dual-role (direct connection)
- 2x USB 3.0 host + 1x USB 2.0 host
* PCIe
- 1x PCIe 2.1 Gen3, 4 lanes
- 2xSATA / 2x PCIe 2.1 Gen1, 2 lanes
* on-module ATtiny816 companion controller, implementing:
- low-power RTC functionality (ISL1208 emulation)
- fan controller (AMC6821 emulation)
* on-module Secure Element with Global Platform 2.2.1 compliant
JavaCard environment
The support is added for Tiger on Haikou devkit, similarly to RK3399
Puma and PX30 Ringneck.
Cc: Quentin Schulz <[email protected]>
Signed-off-by: Quentin Schulz <[email protected]>
Tested-by: Heiko Stuebner <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
Most of the current URLs should be redirected but some aren't already,
so let's anticipate more IT hiccups by migrating to new URLs.
Signed-off-by: Quentin Schulz <[email protected]>
|
|
See
https://embedded.cherry.de/theobroma-systems-is-now-officially-part-of-cherry-se/
While the mail addresses on the theobroma-systems.com domain should be
redirect to cherry.de, let's anticipate IT hiccups and avoid important
mails not reaching us by swapping the domain name wherever appropriate
for the newer one.
Christoph Mueller isn't working at ~Theobroma~ CHERRY Embedded Solutions
anymore, but I don't know his new mail address so mails destined to him
will keep bouncing.
Cc: Heiko Stuebner <[email protected]> <[email protected]>
Cc: Jakob Unterwurzacher <[email protected]>
Cc: Klaus Goger <[email protected]>
Signed-off-by: Quentin Schulz <[email protected]>
|
|
The STM32_RST line is routed to the ATtiny microcontroller
PA0/RESET/UPDI pin. By driving the PX30 SoC pin as GPIO output high, we
prevent external UPDI to be used for flashing without first putting this
pin as GPIO input, an extra step we could avoid in userspace.
There's an external hardware pull-up strong enough to keep the STM32_RST
state high on ATtiny side but weak enough it can be overridden by
external UPDI. This also means it is safe to use for the STM32 variant,
where STM32_RST line will be in the same state as if output high was
used.
The Q7 standard specifies that MFG_NC1 and MFG_NC2 (used for UPDI for
Ringneck) pins should neither be driven by the carrierboard, nor have
pull-up or pull-down resistors. This means this commit is safe to use
regardless of the carrierboard this module would be connected to
(provided it follows the Q7 standard).
Fixes: 6acdd63e8771 ("rockchip: ringneck-px30: always reset STM32 companion controller on boot")
Cc: Quentin Schulz <[email protected]>
Signed-off-by: Quentin Schulz <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-rockchip into next
Please pull the updates for rockchip platform:
- Add board: rk3588 Generic, Cool Pi CM5, Theobroma-Systems RK3588 Jaguar SBC,
Toybrick TB-RK3588X;
rk3588s Cool Pi 4B;
rk3566 Pine64 PineTab2;
- Add saradc v2 support;
- Add PMIC RK806 support;
- rk3588 disable force_jtag by default;
- Migrate to use IO-domain driver for all boards;
- Use common bss and stack addresses for rk33xx and rk35xx boards;
- Other updates for driver, config and dts;
|
|
Currently, if the environment is stored on an MMC device, the device
number is hardcoded by CONFIG_SYS_MMC_ENV_DEV. This is problematic
because many boards can choose between booting from an SD card or a
removable eMMC. For example, the Rock64 defconfig sets
CONFIG_SYS_MMC_ENV_DEV=1, which corresponds to the SD card. If an eMMC
is used as the boot device and no SD card is installed, it is impossible
to save the environment.
To avoid this problem, we can choose the environment MMC device based on
the boot device. The theobroma-systems boards already contain code to do
this, so this commit simply moves it to the common Rockchip board file,
with some refactoring. I also removed another implementation of
mmc_get_env_dev() from tinker_rk3288 that performed MMC boot device
detection by reading a bootrom register.
This has been tested on a Rock64v2.
Signed-off-by: Ben Wolsieffer <[email protected]>
Reviewed-by: Quentin Schulz <[email protected]>
|
|
Switch to use the IO-domain driver to configure IO-domain based on
device tree instead of a setup_iodomain() function.
Signed-off-by: Jonas Karlman <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
While there are currently uses for a stanza of "config BOARD_SPECIFIC_OPTIONS"
followed by "def_bool y" and a series of select/imply statements, having
this option set followed by nothing else doesn't provide anything.
Remove these stanzas.
Signed-off-by: Tom Rini <[email protected]>
|
|
The original link returns a custom 404, so let's point to a link that
works today instead.
Cc: Quentin Schulz <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
Signed-off-by: Quentin Schulz <[email protected]>
|
|
This migrates the plaintext README in
board/theobroma-systems/ringneck_px30 to doc/board/theobroma-systems and
while doing so, update the instructions and rewrite it in rST.
Cc: Quentin Schulz <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
Signed-off-by: Quentin Schulz <[email protected]>
|
|
This migrates the plaintext README in
board/theobroma-systems/puma_rk3399 to doc/board/theobroma-systems and
while doing so, update the instructions and rewrite it in rST.
Cc: Quentin Schulz <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
Signed-off-by: Quentin Schulz <[email protected]>
|
|
There are multiple Device Trees in U-Boot git repo for Puma, so let's
make the MAINTAINERS entry match them all.
Cc: Quentin Schulz <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
Signed-off-by: Quentin Schulz <[email protected]>
|
|
JAGUAR is a Single-Board Computer (SBC) based around the rk3588 SoC and
is targeting Autonomous Mobile Robots (AMR).
It features:
* LPDDR4X (up to 16GB)
* 1Gbps Ethernet on RJ45 connector (KSZ9031 or KSZ9131)
* PCIe 3.0 4-lane on M.2 M-key connector
* PCIe 2.1 1-lane on M.2 E-key
* USB 2.0 on M.2 E-key
* 2x USB3 OTG type-c ports with DP Alt-Mode
* USB2 host port
* HDMI output
* 2x camera connectors, each exposing:
* 2-lane MIPI-CSI
* 1v2, 1v8, 2v8 power rails
* I2C bus
* GPIOs
* PPS input
* CAN
* RS485 UART
* FAN connector
* SD card slot
* eMMC (up to 256GB)
* RTC backup battery
* Companion microcontroller
* ISL1208 RTC emulation
* AMC6821 PWM emulation
* On/off buzzer control
* Secure Element
* 80-pin Mezzanine connector for daughterboards:
* GPIOs
* 1Gbps Ethernet
* PCIe 2.1 1-lane
* 2x 2-lane MIPI-CSI
* ADC channel
* I2C bus
* PWM
* UART
* SPI
* SDIO
* CAN
* I2S
* 1v8, 3v3, 5v0, dc-in (12-24V) power rails
The Device Tree comes from next-20240110 Linux kernel.
Cc: Quentin Schulz <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
Signed-off-by: Quentin Schulz <[email protected]>
|
|
The different macros use writel which is defined in asm/io.h, so let's
include the header so users of hardware.h do not need to include
asm/io.h as well.
While at it, remove asm/io.h includes wherever
asm/arch-rockchip/hardware.h is included already.
Cc: Quentin Schulz <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
Signed-off-by: Quentin Schulz <[email protected]>
|
|
Only setup_boottargets differs from the original misc_init_r from
Rockchip mach code, so let's use rockchip_early_misc_init_r instead of
reimplementing the whole misc_init_r from Rockchip.
Cc: Quentin Schulz <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
Signed-off-by: Quentin Schulz <[email protected]>
|
|
Only setup_iodomain() and setup_boottargets differ from the original
misc_init_r from Rockchip mach code, so let's use
rockchip_early_misc_init_r instead of reimplementing the whole
misc_init_r from Rockchip.
Cc: Quentin Schulz <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
Signed-off-by: Quentin Schulz <[email protected]>
|
|
U-Boot proper automatically modifies boot_targets to swap the order in
which MMC storage media are used for standard boot based on which MMC
storage medium was used to load U-Boot proper. This is however only done
if the user has not changed it manually, therefore a check between the
default and current value is done.
This used to work fine until the migration to standard boot where
boot_targets value size in the default environment went above the 32
characters that env_get_default function can return, thus resulting in a
truncated variable.
Therefore the check between default and current value would always fail.
By using the newly added env_get_default_into function, a buffer of
the appropriate size can be allocated on the stack to get the whole
value of boot_targets in the default environment and thus fixing the
check.
Cc: Quentin Schulz <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
Signed-off-by: Quentin Schulz <[email protected]>
|
|
Ringneck PX30 and Puma RK3399 both have the same expectation with regard
to bootstd device order and U-Boot environment storage device, except
that Puma RK3399 also supports SPI Flash.
Let's move all of this into a common file where common logic can be put.
Cc: Quentin Schulz <[email protected]>
Signed-off-by: Quentin Schulz <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
To prepare to put the similar logic around storage medium selection for
Ringneck PX30 and Puma RK3399 in common, let's not use hardcoded paths
but use uclass functions instead to find udevice based on their DT node
full path.
Cc: Quentin Schulz <[email protected]>
Signed-off-by: Quentin Schulz <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
To prepare to put the similar logic around storage medium selection for
Ringneck PX30 and Puma RK3399 in common, let's not use hardcoded paths
but use uclass functions instead to find udevice based on their DT node
full path.
Cc: Quentin Schulz <[email protected]>
Signed-off-by: Quentin Schulz <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
It's happened that glitches on the STM32_RST and STM32_BOOT lines have
put the STM32 companion microcontroller into DFU mode making it not boot
its FW, rendering it useless for the user.
Considering that the STM32 companion microcontroller is always reset on
a reboot or power cycle, resetting it once again in U-Boot SPL isn't
going to hurt it any more.
For ATtiny companion microcontroller, the situation is a bit different
because a reboot or power cycle doesn't reset it. Additionally, since it
can only be reset with a UPDI reset on the STM32_RST line, and that is
virtually impossible to mistakenly trigger, the ATtiny is unlikely to be
in unwanted reset or enter reset because U-Boot toggles STM32_RST line.
Cc: Quentin Schulz <[email protected]>
Signed-off-by: Quentin Schulz <[email protected]>
Reviewed-by: Heiko Stuebner <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
As part of reviewing a new platform, Daniel Schwierzeck noted that we
can have an empty Makefile in the board directory and don't need an
empty board.c file as well. Further with further cleanup in the
Makefile we can now omit the Makefile entirely. Remove a number of now
unnecessary board.c and Makefiles.
Signed-off-by: Tom Rini <[email protected]>
|
|
Instead of letting the compiler error out if CONFIG_ENV_IS_NOWHERE is
not selected by the user, let's just enforce it when the user builds for
Ringneck PX30 so that no check needs to be performed by the compiler and
the configuration is always valid.
Suggested-by: Tom Rini <[email protected]>
Cc: Quentin Schulz <[email protected]>
Signed-off-by: Quentin Schulz <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
Instead of letting the compiler error out if CONFIG_ENV_IS_NOWHERE is
not selected by the user, let's just enforce it when the user builds for
Puma RK3399 so that no check needs to be performed by the compiler and
the configuration is always valid.
Suggested-by: Tom Rini <[email protected]>
Cc: Quentin Schulz <[email protected]>
Signed-off-by: Quentin Schulz <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
The PX30-µQ7 (Ringneck) is a system-on-module featuring the Rockchip
PX30 in a micro Qseven-compatible form-factor.
PX30-µQ7 features:
* CPU: quad-core Cortex-A35
* DRAM: 2GB dual-channel
* eMMC: onboard eMMC
* SD/MMC
* TI DP83825I 10/100Mbps PHY
* USB:
* USB2.0 dual role port
* 3x USB2.0 host via onboard USB2.0 hub
* Display: MIPI-DSI
* Camera: MIPI-CSI
* onboard 2.4GHz WiFi + Bluetooth module
* Companion Controller: on-board additional microcontroller
(STM32 Cortex-M0 or ATtiny):
* RTC
* fan controller
* CAN (only STM32)
The non-U-Boot DTS files are imported from Linux v6.2-rc2.
Cc: Quentin Schulz <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
Signed-off-by: Quentin Schulz <[email protected]>
|
|
Now that a single binary containing TPL/SPL correctly formatted for SPI
flashes and U-Boot proper, can be generated by binman, let's do it.
Also update the documentation to tell the user to use this newly
generated file instead of manually generating and flashing the binaries.
Cc: Quentin Schulz <[email protected]>
Signed-off-by: Quentin Schulz <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
The offset of the SPL payload on Puma is different than for other
Rockchip devices in that it is stored at offset 256K instead of much
further away in the MMC.
Flashing one binary instead of two at different offsets is much more
user friendly so let's migrate to it by modifying the offset in the Puma
specific Device Tree.
Cc: Quentin Schulz <[email protected]>
Signed-off-by: Quentin Schulz <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
Depending on the toolchain used to compile the SPL for Puma RK3399-Q7
module, the board does not boot because the resulting binary is too big
to fit in SRAM.
Let's add a TPL so that there's no need to fiddle with or hack the
defconfig to have a working bootloader.
This follows what's been done for the majority of other RK3399-based
boards.
See the original commit for the first migrations:
bdc00080111f "rockchip: rk3399: update defconfig for TPL"
Unfortunately, the offset in SPI-NOR for U-Boot proper needs to be
modified, since the move from SPL to TPL+SPL for idbloader.img (and the
"only the first 2KB per 4KB blocks are written" "hack" for rkspi format)
increased the size above 256KB. Let's move it to 512KB to, hopefully, be
safe.
Cc: Quentin Schulz <[email protected]>
Signed-off-by: Quentin Schulz <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
U-Boot proper
Chances are when one boots U-Boot proper from a given storage medium,
they want the same medium to be used to load and store the environment.
This basically allows to have completely separate U-Boot (TPL/SPL/U-Boot
proper/environment) per storage medium which is convenient when working
with recovery from SD-Card as one would just need to insert a properly
configured SD-Card into the device to have access to their whole debug
setup.
No fallback mechanism is provided as to not dirty other storage medium
environment by mistake. However, since arch_env_get_location() is called
by env_init() which is part of the pre-relocation process, a valid,
non-ENVL_UNKNOWN, value shall be returned otherwise the relocation fails
with the following message:
initcall sequence 00000000002866c0 failed at call 0000000000256b34 (err=-19)
This valid, non-ENVL_UNKNOWN, value is ENVL_NOWHERE which requires to
always select CONFIG_ENV_IS_NOWHERE otherwise this work-around does not
work.
Cc: Quentin Schulz <[email protected]>
Signed-off-by: Quentin Schulz <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
U-Boot proper
Automatically detect which MMC device (SD-Card or eMMC) was used to load
U-Boot proper and load the environment from that MMC device instead of
a hardcoded one.
Cc: Quentin Schulz <[email protected]>
Signed-off-by: Quentin Schulz <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
CONFIG_ENV_OFFSET is set in the defconfig to a different value already
so this isn't used. Let's remove it as to not confuse users.
Cc: Quentin Schulz <[email protected]>
Signed-off-by: Quentin Schulz <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
medium
distroboot should try first on the same MMC medium as the one the SPL
loaded U-Boot proper from. This was the case when the introducing commit
was merged because the default order was eMMC first and then SD card.
The check was therefore made only on whether we booted from SD card,
because otherwise the order was the expected one.
However, in commit b212ad24a604 ("rockchip: Fix MMC boot order"), the
order was swapped. Meaning our simple check is now useless.
Let's fix that by accounting for all scenarii: default boot_targets has
mmc0 first but booting from SD Card, mmc1 first but booting from eMMC.
Fixes: b212ad24a604 ("rockchip: Fix MMC boot order")
Cc: Quentin Schulz <[email protected]>
Signed-off-by: Quentin Schulz <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
CONFIG_SERIAL_TAG is not selectable for ARM64 machines. While
get_board_serial is weakly defined if ENV_VARS_UBOOT_RUNTIME_CONFIG is
defined, it is only called when CONFIG_SUPPORT_PASSING_ATAGS is defined,
which also is not selectable for ARM64 machines. Therefore this is dead
code so let's remove it.
Cc: Quentin Schulz <[email protected]>
Signed-off-by: Quentin Schulz <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
Philipp does not work at Theobroma Systems anymore so let's swap
Philipp's address with mine.
Cc: Philipp Tomsich <[email protected]>
Cc: Quentin Schulz <[email protected]>
Signed-off-by: Quentin Schulz <[email protected]>
Reviewed-by: Philipp Tomsich <[email protected]>
|
|
Long gone is the time a custom TF-A was needed for Puma, upstream TF-A
works just fine now.
The flashing instructions are updated to match how newer rkdeveloptool
and rkbin work.
Finally, rkbin provides a way to flash SPI via USB OTG interface so
let's document that.
Cc: Quentin Schulz <[email protected]>
Signed-off-by: Quentin Schulz <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
On Puma we have the environment at an offset of 16 kiB.
On the eMMC this gives us 16 kiB for the environment before the SPL starts.
On the SPI NOR we also have 16 kiB until end of flash.
So let's increase the environment size from 8 kiB to its maximum
of 16 kiB for both MMC and SPI NOR.
Signed-off-by: Christoph Muellner <[email protected]>
Reviewed-by: Heiko Stuebner <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
With the current usb stack in u-boot, all host ports on puma work
flawlessly without any additional special handling, so drop that
usb hub hacking from the puma board.
Tested with mass-storage and usb-ethernet on both usb3 and usb2 ports.
Signed-off-by: Heiko Stuebner <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
Reviewed-by: Philipp Tomsich <[email protected]>
|
|
The introduction of the puma-specific generator was mainly a way
to split the pmu firmware from the ATF binary and not having to
distribute that 4GB (sparse) image that was created before moving
to the bl31.elf as base.
Looking at the publically available repository for that separate
pmu firmware
https://git.theobroma-systems.com/rk3399-cortex-m0.git/
there is also no activity for 3 years and apart from some build
customizations no other changes were done.
And even then, if changes need to be made, this can very well also
happen in the atf context itself, so there is no real need to
diverge from the established build procedure and we can just go
back to using the main make_fit_atf.py script.
Signed-off-by: Heiko Stuebner <[email protected]>
Reviewed-by: Philipp Tomsich <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
So far the puma dts files only just included the main puma dtsi without
handling the actual baseboard and rk3399-puma.dtsi was very much
detached from the variant in the mainline Linux kernel.
Recent changes resulted in a strange situation with nonworking puma boards.
Commit ab800e5a6f28 ("arm: dts: rockchip: puma: move U-Boot specific bits to u-boot.dtsi")
moved the sdram include from rk3399-puma-ddrX.dts to new files
rk3399-puma-ddrx-u-boot.dtsi which were never included anywhere though.
Commit 167efc2c7a46 ("arm64: dts: rk3399: Sync v5.7-rc1 from Linux")
replaced the rk3399-puma.dtsi nearly completely, but in the kernel
it definitly depends on a baseboard dts to actually enable peripherals
like sd-slot, uarts, etc.
So to untagle this and bring the whole thing more in line with mainline
Linux, bring the rk3399-puma-haikou.dts over as well, drop the separate
DDR-option devicetrees and instead replace them with a puma Kconfig option
to select and include the needed DDR variant.
Signed-off-by: Heiko Stuebner <[email protected]>
Reviewed-by: Philipp Tomsich <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
The commit moving puma to the generic cpuid/macaddr helpers used 7 spaces
as indentation, so correct that by moving to the required tabs.
Fixes: fa177ff0208b ("board: puma: Use rockchip_* helpers to setup cpuid and macaddr")
Signed-off-by: Heiko Stuebner <[email protected]>
Reviewed-by: Philipp Tomsich <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
When building U-Boot we select the architecture via Kconfig and not ARCH
being passed in via the environment or make cmdline.
Acked-by: Kever Yang <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Philipp Tomsich <[email protected]>
Acked-by: Klaus Goger <[email protected]>
Cc: Jagan Teki <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Linux v5.7-rc1 dts(i) sync has changed the sdmmc node from
dwmmc@fe320000 to mmc@fe320000 and this ofpath is being
used in rockchip spl bootdevice code.
So, update the ofpath with a new node name and prefix "same-as-spl"
to missing u-boot,spl-boot-order.
Bug log:
U-Boot SPL 2020.07-rc2-00256-g9c5fef5774 (May 24 2020 - 20:20:43 +0530)
Trying to boot from MMC2
mmc_load_image_raw_sector: mmc block read error
Trying to boot from MMC1
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
Fixes: 167efc2c7a46 ("arm64: dts: rk3399: Sync v5.7-rc1 from Linux"
Signed-off-by: Suniel Mahesh <[email protected]>
Signed-off-by: Jagan Teki <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
The make_fit_spl scripts get the dtb to use as commandline option,
so use it for puma as well.
Signed-off-by: Heiko Stuebner <[email protected]>
|
|
Move this header out of the common header.
Signed-off-by: Simon Glass <[email protected]>
|
