| Age | Commit message (Collapse) | Author |
|---|
|
The first 4 block copy channels and rings on AM62P support
High Capacity Block Copy. These channels have approximately
3x improvement over the normal Block copy channels when doing
DDR-to-DDR copy.
Currently, during allocation these channels do not have a
separate interface and are allocated with normal BCDMA channels.
Latest TIFS and DM firmware adds support for differentiating these
High Capcity resources. This update is for allocating these new
resource type to different hosts with below mentioned scheme.
--------------------- --------------- ------------- ----------------
Resource A53_2 MCU_R5 WKUP_R5
--------------------- --------------- ------------- ----------------
BCDMA HC CHAN [4] => 2 (Primary) 1 (Primary) 1 (Primary)
BCDMA HC CHAN RING [4] => 2 (Primary) 1 (Primary) 1 (Primary)
BCDMA CHAN [4] => 18 (Primary) 2 (Primary) 6 (Primary)
BCDMA CHAN RING[4] => 18 (Primary) 2 (Primary) 6 (Primary)
Signed-off-by: Sparsh Kumar <[email protected]>
Signed-off-by: Sebin Francis <[email protected]>
Signed-off-by: Vishal Mahaveer <[email protected]>
|
|
Update rm-cfg.yaml and tifs-rm-cfg.yaml to account for the
changes added in the K3 Resource Partitioning Tool v1.18
The change enables resource sharing between A72_2 and MAIN_0_R5_0
for the BCDMA CSI RX and TX channels, J784S4 supports upto 12
CSI cameras and 16 channels would not be enough for all such use
cases for RTOS and Linux, thus sharing of resources in needed. Resource
sharing between A72 and R5 for BCDMA CSI channels allow Linux to use 32
channels at a time.
Signed-off-by: Vaishnav Achath <[email protected]>
[[email protected]: rebased and sent on behalf]
Signed-off-by: Neha Malcom Francis <[email protected]>
Reviewed-by: Udit Kumar <[email protected]>
|
|
Siddharth Vadapalli <[email protected]> says:
This series enables USB DFU and USB Mass Storage functionality for
AM62, AM62-LP, AM62A, AM62P and J722S SoCs.
Link: https://lore.kernel.org/r/[email protected]
|
|
Include the TI K3 DFU environment to support DFU Boot and DFU Flash.
Signed-off-by: Siddharth Vadapalli <[email protected]>
|
|
Include the TI K3 DFU environment to support DFU Boot and DFU Flash.
Also add "usb" to the list of "boot_targets". While at it, add a newline
at the end of the file.
Signed-off-by: Siddharth Vadapalli <[email protected]>
Reviewed-by: Mattijs Korpershoek <[email protected]>
Reviewed-by: Roger Quadros <[email protected]>
|
|
The CPSW3G instance of CPSW on AM62PX SoC provides Ethernet functionality.
Currently, Ethernet is supported on Linux which runs on the A53 core on the
SoC, by allocating all of the DMA resources associated with CPSW to A53_2.
In order to enable use-cases where the Ethernet traffic is sent from or
consumed by various CPU cores on the SoC simultaneously, while at the
same time, maintaining backward compatibility with the existing use-case
of A53 being the sole entity that exchanges traffic with CPSW via DMA,
update the DMA resource sharing scheme on AM62PX SoC to the following:
--------------- -------------- ------------- ----------------
Resource WKUP_R5 MCU_R5 A53_2
--------------- -------------- ------------- ----------------
TX Channels [8] => 4 (Primary) 4 (Primary) 8 (Secondary)
TX Rings [64] => 32 (Primary) 32 (Primary) 64 (Secondary)
RX Channels [1] => 1 (Primary) 0 1 (Secondary)
RX Flows [16] => 6 (Primary) 10 (Primary) 16 (Secondary)
In the absence of primary owners of resources (existing use-case
where A53 owns all of the CPSW DMA resources), the secondary owner
can claim all of the resources as its own. For shared use-cases,
the resources that are not claimed by the primary are communicated
to the secondary owner allowing it to claim them. This ensures that
Linux on A53_2 can continue claiming all DMA resources associated
with CPSW in the absence of primary owners, while at the same time
providing users the flexibility to share CPSW DMA resources across
various CPU cores listed above if needed.
While Linux has been mentioned as the Operating System running
on A53, there is no dependency between the Operating System
running on A53 and its ability to claim the CPSW DMA resources
listed above.
Signed-off-by: Siddharth Vadapalli <[email protected]>
|
|
Judith Mendez <[email protected]> says:
Some K3 devices like am62x and am64x have a M4 processor in the MCU
voltage domain. This patch series introduces remoteproc M4 driver which
will be used to load firmware into and start the M4 remote core.
This series also adds support for R5F cores on am64x SoCs in patch 2 and
sets up environment to load FW in remote cores in patch 3,4,5.
This patch series also enables remoteproc drivers by default as per what
remoteproc sybsystem is supported per SoC, thus all remoteproc options
are now deleted in configs/* since they are no longer required.
This patch series was tested on am64x EVM, am62x SK, am62ax SK,
am62px SK boards.
Any additional tested by's are welcome since I was not able to
test any additional boards.
Tested by running the following commands in u-boot prompt:
=> setenv dorprocboot 1
=> run boot_rprocs
Link: https://lore.kernel.org/r/[email protected]
|
|
Add remoteproc specific env support for am62px device. If the
remoteproc CMD is defined, include the K3 remoteproc environment.
Also define rproc_fw_binaries which holds a list of remoteproc FW
binaries for u-boot loading of remote cores.
Signed-off-by: Hari Nagalla <[email protected]>
Signed-off-by: Judith Mendez <[email protected]>
Reviewed-by: Andrew Davis <[email protected]>
|
|
Add remoteproc specific env support for am62x device. If the
remoteproc CMD is defined, include the K3 remoteproc environment.
Also define rproc_fw_binaries which holds a list of remoteproc FW
binaries for u-boot loading of remote cores.
Signed-off-by: Hari Nagalla <[email protected]>
Signed-off-by: Judith Mendez <[email protected]>
Reviewed-by: Andrew Davis <[email protected]>
|
|
Add remoteproc specific env support for am64x device. If the
remoteproc CMD is defined, include the K3 remoteproc environment.
Also define rproc_fw_binaries which holds a list of remoteproc FW
binaries for u-boot loading of remote cores.
Signed-off-by: Hari Nagalla <[email protected]>
Signed-off-by: Judith Mendez <[email protected]>
Reviewed-by: Andrew Davis <[email protected]>
|
|
This config is causing conflicts with how fdtfile variable is
initialized.
For K3 devices, CONFIG_DEFAULT_DEVICE_TREE= "ti/k3-<board>.dtb".
With CONFIG_TI_FDT_FOLDER_PATH also prefixing "ti", fdtfile is then
"ti/ti/k3-<board>.dtb". This variable is updated when fitImage is
booted and fails to boot due to the parsing error "ti/ti/".
Given that there are no other users of this config other than K3 for
now, it is being removed.
Since am64x, j721e and j721s2 also define a DEFAULT_FDT_FILE, update
them to conform to the DEFAULT_DEVICE_TREE standard.
Signed-off-by: Aashvij Shenai <[email protected]>
|
|
Include k3_rproc.env to access rproc boot commands and specify rproc
firmware names for adding remoteproc support in J722S SoCs.
Signed-off-by: Beleswar Padhi <[email protected]>
Reviewed-by: Bryan Brattlof <[email protected]>
|
|
size when ECC is enabled
As there are few redundant functions in board/ti/*/evm.c files, pull
them to a common location of access to reuse and include the common file
to access the functions.
Call k3-ddrss driver through fixup_ddr_driver_for_ecc() to fixup the
device tree and resize the available amount of DDR, if ECC is enabled.
Otherwise, fixup the device tree using the regular
fdt_fixup_memory_banks().
Also call dram_init_banksize() after every call to
fixup_ddr_driver_for_ecc() is made so that gd->bd is populated
correctly.
Ensure that fixup_ddr_driver_for_ecc() is agnostic to the number of DDR
controllers present.
Signed-off-by: Santhosh Kumar K <[email protected]>
Signed-off-by: Neha Malcom Francis <[email protected]>
Reviewed-by: Wadim Egorov <[email protected]>
|
|
Neha Malcom Francis <[email protected]> says:
Enable the NFS command across all platforms to allow network booting via
the NFS. Clean up the J7 configs to use TI_COMMON_CMD_OPTIONS.
Link: https://lore.kernel.org/r/[email protected]
|
|
Add CMD_NFS to list of configs implied by CONFIG_TI_COMMON_CMD_OPTIONS.
This allows network booting via the NFS protocol from the U-Boot prompt.
Fixes: 10de12570799 ("disable NFS support by default")
Signed-off-by: Neha Malcom Francis <[email protected]>
|
|
Siddharth Vadapalli <[email protected]> says:
Hello,
This series adds support for USB DFU boot on TI's AM62A SoC which has
two instances of DWC3 USB Controllers namely USB0 and USB1. The USB0
instance of the USB Controller supports USB DFU boot:
ROM => tiboot3.bin => tispl.bin => u-boot.img
USB DFU Boot requires the USB Controller to be configured for Gadget
mode of operation. Since the USB0 instance of the DWC3 USB Controller
supports both Host and Gadget modes of operation via the Type-C interface
on the AM62A7-SK board, the device-tree specifies the "dr_mode" as "OTG".
However, there is currently no support for dynamically switching the "mode"
from Host to Gadget and vice-versa with the help of a state-machine.
The OTG mode is treated as a separate mode in itself rather than being
treated as an intermediate stage before assuming the Host/Gadget mode.
Due to this, USB DFU boot via the Type-C interface doesn't work as the
USB Controller hasn't been appropriately configured for Device/Gadget
mode of operation. One option is to change the device-tree to specify
"dr_mode" as "peripheral" and force the controller to assume the Device
role. This will imply that the U-Boot device-tree for AM62A diverges
from its Linux counterpart. Therefore, with the intent of keeping the
device-tree uniform across Linux and U-Boot, and at the same time, in
order to enable USB DFU boot in "OTG" mode with the DWC3 Controller,
the first patch in this series sets the "mode" on the basis of the
caller function, rather than using the "dr_mode" property in the
device-tree. There are only two callers of "dwc3_generic_probe()",
each of which clearly specify the expected mode of configuration.
This will enable both Host and Device mode of operation based on the
command executed by the user, thereby truly supporting "OTG"
functionality when the USB Controller supports it.
The second patch in this series adds USB DFU environment for AM62A,
enabling USB DFU Boot and USB DFU flash on AM62A.
In addition to the patches in this series, the following device-tree
changes will be required to test USB DFU on AM62A (bootph-all property
to be added to ensure that USB Controller is present at all stages
for DFU Boot):
https://gist.github.com/Siddharth-Vadapalli-at-TI/53ba02cb0ff4a09c47e920d08247065f
The above device-tree changes will be made to the Linux device-tree,
which shall ensure that the same shall be a part of U-Boot device-tree
eventually.
The USB DFU config fragments for AM62x have been used for enabling
USB DFU boot on AM62a as follows:
R5 => am62ax_evm_r5_defconfig + am62x_r5_usbdfu.config
A53 => am62ax_evm_a53_defconfig + am62x_a53_usbdfu.config
Logs validating USB DFU boot with this series:
https://gist.github.com/Siddharth-Vadapalli-at-TI/daa71da1b0e478a51afea42605fb2d2c
Link: https://lore.kernel.org/r/[email protected]
|
|
Include the TI K3 DFU environment to support DFU Boot and DFU Flash.
Signed-off-by: Siddharth Vadapalli <[email protected]>
Reviewed-by: Roger Quadros <[email protected]>
|
|
Initialize the 3 instances of SOC ESM & PMIC ESM.
This is needed for watchdog functionality.
Signed-off-by: Keerthy <[email protected]>
Signed-off-by: Udit Kumar <[email protected]>
|
|
Create an SoC R5 dtsi file that could be used at board level R5 files. This
would help in keeping the SoC level changes in sync across board files.
Signed-off-by: Manorit Chawdhry <[email protected]>
|
|
Bastien Curutchet <[email protected]> says:
Hi all,
This patch series aims to add DM support for the AEMIF controller that
can be found in the DaVinci SoCs.
This controller has already a driver used by the Keystone SoCs so I
add my work to it.
As we can now easily import Linux device-trees, I try to stick the
most I can to the Linux bindings of the AEMIF controller. To do so I add
an 'intermediate' driver called 'ti-aemif-cs'. It's in charge of
configuring timings for a given chip select of the AEMIF controller.
Link: https://lore.kernel.org/r/[email protected]
|
|
AEMIF controller is present on other SoCs than the Keystone ones.
Remove Keystone specificities from the driver to be able to use it from
other architectures.
Adapt the ks2_evm/board.c to fit the new driver.
Signed-off-by: Bastien Curutchet <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Update simple-framebuffer device-tree node by enumerating framebuffer
related information in existing simple-framebuffer node in Linux
device-tree file and enabling it.
In case there is no simple-framebuffer stub detected in Linux kernel
device-tree and video is still active, then update the device-tree to
reserve the framebuffer region for the active splash screen.
This helps preserve the splash screen till the display server takes over
after OS is booted.
Signed-off-by: Devarsh Thakkar <[email protected]>
|
|
Add what it takes to enable NETDEVICES with NET_LWIP and enable DHCP as
well as the dhcp command. CMD_TFTPBOOT is selected by BOOTMETH_EFI due
to this code having an implicit dependency on do_tftpb().
Note that PXE is likely non-fonctional with NET_LWIP (or at least not
100% functional) because DHCP option 209 is not supported by the lwIP
library. Therefore, BOOTP_PXE_DHCP_OPTION cannot be enabled.
Signed-off-by: Jerome Forissier <[email protected]>
Tested-by: Ilias Apalodimas <[email protected]>
Acked-by: Ilias Apalodimas <[email protected]>
|
|
Simon Glass <[email protected]> says:
When the SPL build-phase was first created it was designed to solve a
particular problem (the need to init SDRAM so that U-Boot proper could
be loaded). It has since expanded to become an important part of U-Boot,
with three phases now present: TPL, VPL and SPL
Due to this history, the term 'SPL' is used to mean both a particular
phase (the one before U-Boot proper) and all the non-proper phases.
This has become confusing.
For a similar reason CONFIG_SPL_BUILD is set to 'y' for all 'SPL'
phases, not just SPL. So code which can only be compiled for actual SPL,
for example, must use something like this:
#if defined(CONFIG_SPL_BUILD) && !defined(CONFIG_TPL_BUILD)
In Makefiles we have similar issues. SPL_ has been used as a variable
which expands to either SPL_ or nothing, to chose between options like
CONFIG_BLK and CONFIG_SPL_BLK. When TPL appeared, a new SPL_TPL variable
was created which expanded to 'SPL_', 'TPL_' or nothing. Later it was
updated to support 'VPL_' as well.
This series starts a change in terminology and usage to resolve the
above issues:
- The word 'xPL' is used instead of 'SPL' to mean a non-proper build
- A new CONFIG_XPL_BUILD define indicates that the current build is an
'xPL' build
- The existing CONFIG_SPL_BUILD is changed to mean SPL; it is not now
defined for TPL and VPL phases
- The existing SPL_ Makefile variable is renamed to SPL_
- The existing SPL_TPL Makefile variable is renamed to PHASE_
It should be noted that xpl_phase() can generally be used instead of
the above CONFIGs without a code-space or run-time penalty.
This series does not attempt to convert all of U-Boot to use this new
terminology but it makes a start. In particular, renaming spl.h and
common/spl seems like a bridge too far at this point.
The series is fully bisectable. It has also been checked to ensure there
are no code-size changes on any commit.
|
|
Use XPL_ as the symbol to indicate an SPL build. This means that SPL_ is
no-longer set.
Signed-off-by: Simon Glass <[email protected]>
|
|
Use the new symbol to refer to any 'SPL' build, including TPL and VPL
Signed-off-by: Simon Glass <[email protected]>
|
|
Update J722S Resource Management configs to the latest output
generated by K3 Resource Partitioning tool. Main change includes
allocating more BCDMA channels to A53 for CSI2RX to support
4 x CSIRX capture instance simultaneously.
Signed-off-by: Vaishnav Achath <[email protected]>
Reviewed-by: Jayesh Choudhary <[email protected]>
|
|
Guillaume La Roque <[email protected]> says:
Ths patchset add support of Android 14 with boot image version 4
for :
- AM62X-SK EVM: https://www.ti.com/tool/SK-AM62B
- BeaglePlay: https://beagleplay.org/
- AM62PX-SK EVM: https://www.ti.com/tool/SK-AM62P-LP
Android Images use to test this series are on the Official TI website:
- AM62x/BeaglePlay: https://www.ti.com/tool/PROCESSOR-SDK-AM62X
- AM62PX: https://www.ti.com/tool/PROCESSOR-SDK-AM62P
|
|
When CONFIG_BOOTMETH_ANDROID is set, enable Android boot flow support.
To build for AM62Px for Android, we can re-use
the am62x_a53_android.config fragment when building A53 bootloaders:
$ make am62px_evm_a53_defconfig
$ make am62x_a53_android.config
$ make
Signed-off-by: Mattijs Korpershoek <[email protected]>
Reviewed-by: Mattijs Korpershoek <[email protected]>
Signed-off-by: Guillaume La Roque <[email protected]>
Reviewed-by: Bryan Brattlof <[email protected]>
|
|
Add Android bootflow support for AM62X SK EVM board with
new android boot method.
To build for AM62x for Android, we use the
am62x_a53_android.config fragment when building A53 bootloaders:
$ make am62x_evm_a53_defconfig
$ make am62x_a53_android.config
$ make
Co-developed-by: Mattijs Korpershoek <[email protected]>
Signed-off-by: Mattijs Korpershoek <[email protected]>
Signed-off-by: Guillaume La Roque <[email protected]>
Reviewed-by: Mattijs Korpershoek <[email protected]>
Reviewed-by: Bryan Brattlof <[email protected]>
|
|
Chintan Vankar <[email protected]> says:
This series enables Ethernet Boot on SK-AM62 device.
This series is based on commit 'f4f845b85926' of origin/next branch of
U-Boot.
Logs for Ethernet Boot for AM625-SK:
https://gist.github.com/chintanv133/464782796a9a60b9f5a49e674c5fc31a
|
|
This board has not been converted to CONFIG_DM_I2C by the deadline.
Remove it.
Signed-off-by: Tom Rini <[email protected]>
|
|
This board has not been converted to CONFIG_DM_I2C by the deadline.
Remove it.
Acked-by: Robert Nelson <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Drop all duplicate newlines. No functional change.
Signed-off-by: Marek Vasut <[email protected]>
|
|
Manorit Chawdhry <[email protected]> says:
fdtfile wasn't being populated in these boards in legacy boot using
bootcmd_ti_mmc, migrate these platforms to ti_set_fdt_env.
|
|
stdboot and legacy boot depend on fdtfile. Since findfdt is getting
deprecated, move the rest of k3 platforms dependent on findfdt to
ti_set_fdt_env.
Populate fdtfile by calling ti_set_fdt_env in board files.
Signed-off-by: Manorit Chawdhry <[email protected]>
|
|
|
|
Now that am335x_evm boots OK on the Beaglebone black, drop the latter
and update the docs to cover the change.
Also add a few updates about 'make fit' and drop the note about the
security review, as U-Boot's verified boot has had quite extensive
review now.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
MD Danish Anwar <[email protected]> says:
This series adds config changes and env changes to enable ICSSG Ethernet
Driver on AM64x.
|
|
When ICSSG driver is enabled (CONFIG_TI_ICSSG_PRUETH=y) set
storage_interface and fw_dev_part env variables.
These variables need be set appropriately in order to load different
ICSSG firmwares needed for ICSSG driver. By default the storage
interface is mmc and the partition is 1:2. User can modify this based on
their needs.
Signed-off-by: MD Danish Anwar <[email protected]>
|
|
Jayesh Choudhary <[email protected]> says:
Hello there,
This series add the U-Boot support for our new platform of K3-SOC
family - J722S-EVM which is a superset of AM62P. It shares the same
memory map and thus the nodes are being reused from AM62P includes
instead of duplicating the definitions.
Some highlights of J722S SoC (in addition to AM62P SoC features) are:
- Two Cortex-R5F for Functional Safety or general-purpose usage and
two C7x floating point vector DSP with Matrix Multiply Accelerator
for deep learning.
- Vision Processing Accelerator (VPAC) with image signal processor
and Depth and Motion Processing Accelerator (DMPAC).
- 7xUARTs, 3xSPI, 5xI2C, 2xUSB2, 2xCAN-FD, 3xMMC and SD, GPMC for
NAND/FPGA connection, OSPI memory controller, 5xMcASP for audio,
4xCSI-RX for Camera, 1 PCIe Gen3 controller, USB3.0 eCAP/eQEP,
ePWM, among other peripherals.
TRM: <https://www.ti.com/lit/zip/sprujb3>
Schematics: <https://www.ti.com/lit/zip/sprr495>
Boot test log:
<https://gist.github.com/Jayesh2000/0313e58fde377f877a9a8f1acc2579ef>
|
|
Introduce the basic files needed to support the TI J722S family of SoCs.
Co-developed-by: Vaishnav Achath <[email protected]>
Signed-off-by: Vaishnav Achath <[email protected]>
Signed-off-by: Jayesh Choudhary <[email protected]>
|
|
Define the firmware components updatable via EFI capsule update, including
defining capsule GUIDs for the various firmware components for the AM69
SK.
TODO: possibly make the struct's sk specific.
TODO: add doc commit (and make sure doc is sk/NOR specific, and add OSIP
boot mode)
TODO: update doc to show sk defconfig when building
Signed-off-by: Jonathan Humphreys <[email protected]>
Acked-by: Ilias Apalodimas <[email protected]>
|
|
Define the firmware components updatable via EFI capsule update, including
defining capsule GUIDs for the various firmware components for the AM62px
SK.
Signed-off-by: Jonathan Humphreys <[email protected]>
Acked-by: Ilias Apalodimas <[email protected]>
|
|
Define the firmware components updatable via EFI capsule update, including
defining capsule GUIDs for the various firmware components for the AM62x
SK.
Signed-off-by: Jonathan Humphreys <[email protected]>
Acked-by: Ilias Apalodimas <[email protected]>
|
|
Define the firmware components updatable via EFI capsule update, including
defining capsule GUIDs for the various firmware components for the
SK-TDA4VM.
Signed-off-by: Jonathan Humphreys <[email protected]>
Acked-by: Ilias Apalodimas <[email protected]>
|
|
Define the firmware components updatable via EFI capsule update, including
defining capsule GUIDs for the various firmware components for the AM64x
SK.
Signed-off-by: Jonathan Humphreys <[email protected]>
Acked-by: Ilias Apalodimas <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Bryan Brattlof <[email protected]> says:
Hello Again Everyone!
The am625-lp-sk is a variant of the am625-sk showcasing the low-power
features of the am625 SoC Family. Because it's essentially a board and
package spin of the am625-sk I've inherited the am625 configuration and
overridden what was needed.
This is a new spin of Nitin's original work which has been updated
significantly since October 2023
https://lore.kernel.org/u-boot/[email protected]/
For those of us interested here is proof of life using buildroot:
https://paste.sr.ht/~bryanb/40f7787f7760bee383aa8fbc342a29e8544dbdab
This also works around a buildman issue not following #include
directives. To get around this I've redefined the variables it's looking
for inside the lp-sk defconfig to keep it happy for now. I made a pull
request on github and everything seems like it's happy
https://dev.azure.com/u-boot/u-boot/_build/results?buildId=8634&view=results
|
|
The am62x-lp-sk is a package and reference board spin of the am62x-sk to
showcase the low-power features of the am62x SoC family. Because it so
closely resembles the am62x-sk board, use the preprocessor to inherit
its configuration making the needed changes for this board where
necessary.
Reviewed-by: Dhruva Gole <[email protected]>
Signed-off-by: Bryan Brattlof <[email protected]>
|
|
Include k3_rproc.env to access rproc boot commands and specify
rproc firmware names for adding remoteproc support in J784S4 SoCs.
Signed-off-by: Beleswar Padhi <[email protected]>
|
