| Age | Commit message (Collapse) | Author |
|---|
|
Resync all defconfig files using qconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
The PCIe0 instance of PCIe on the J722S SoC uses the 4 GB Address Window
starting from 0x6_0000_0000 to map System Addresses to PCIe Bus Addresses.
Hence, enable CONFIG_SYS_PCI_64BIT.
Signed-off-by: Siddharth Vadapalli <[email protected]>
Fixes: 79f3e77133bd ("Subtree merge tag 'v6.16-dts' of dts repo [1] into dts/upstream")
|
|
Enable PCIe now that it is fixed.
Signed-off-by: George McCollister <[email protected]>
Tested-by: Bryan Brattlof <[email protected]>
|
|
These are common for all K3 based boards. Add the common values as
defaults and remove from each board defconfig
Signed-off-by: Andrew Davis <[email protected]>
Reviewed-by: Bryan Brattlof <[email protected]>
|
|
Resync all defconfig files using qconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Commit 86acdce2ba88 ("common: add config for board_init() call")
introduced CONFIG_BOARD_INIT option. This option can be disabled for the
boards where board_init() function is not needed. Remove empty
board_init() calls for all boards where it's possible, and disable
CONFIG_BOARD_INIT in all related defconfigs.
This cleanup was made semi-automatically using these scripts: [1].
No functional change, but the binary size for the modified boards is
reduced a bit.
[1] https://github.com/joe-skb7/uboot-convert-scripts/tree/master/remove-board-init
Signed-off-by: Sam Protsenko <[email protected]>
Tested-by: Adam Ford <[email protected]> #imx8mm_beacon
Tested-by: Bryan Brattlof <[email protected]>
Acked-by: Peng Fan <[email protected]> #NXP boards
|
|
SPL_TEXT_BASE is used as the load address for the main domain SPL on k3
platforms.
Since the config value is the same for every board, this patch sets the
value 0x80080000 as default for all 64-bit ARCH_K3, 0x43c00000 as
default for the R5 cores and deletes the instances of SPL_TEXT_BASE in
individual defconfigs.
Signed-off-by: Anshul Dalal <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Siddharth Vadapalli <[email protected]> says:
This series enables USB DFU and USB Mass Storage functionality for
AM62, AM62-LP, AM62A, AM62P and J722S SoCs.
Link: https://lore.kernel.org/r/[email protected]
|
|
The USB0 instance of USB on J722S SoC is a Designware USB Controller with
the same glue layer (wrapper) as AM62 SoC. In order to support USB DFU boot
and USB DFU flash with USB0, enable the corresponding glue layer driver.
While at it, sync with savedefconfig.
Signed-off-by: Siddharth Vadapalli <[email protected]>
|
|
Judith Mendez <[email protected]> says:
Some K3 devices like am62x and am64x have a M4 processor in the MCU
voltage domain. This patch series introduces remoteproc M4 driver which
will be used to load firmware into and start the M4 remote core.
This series also adds support for R5F cores on am64x SoCs in patch 2 and
sets up environment to load FW in remote cores in patch 3,4,5.
This patch series also enables remoteproc drivers by default as per what
remoteproc sybsystem is supported per SoC, thus all remoteproc options
are now deleted in configs/* since they are no longer required.
This patch series was tested on am64x EVM, am62x SK, am62ax SK,
am62px SK boards.
Any additional tested by's are welcome since I was not able to
test any additional boards.
Tested by running the following commands in u-boot prompt:
=> setenv dorprocboot 1
=> run boot_rprocs
Link: https://lore.kernel.org/r/[email protected]
|
|
Now that remoteproc configs are enabled by default in Kconfig
files, remove these configs which are no longer needed to be
defined here in configs/.
Signed-off-by: Judith Mendez <[email protected]>
Reviewed-by: Andrew Davis <[email protected]>
|
|
Resync all defconfig files using qconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Set CONFIG_NR_DRAM_BANKS to 2 as we have two banks described in the
memory/ node for lower and higher addressible DDR regions.
This allows use of FDT functions from fdt_support.c to set up and fix up
the memory/ node correctly.
Signed-off-by: Neha Malcom Francis <[email protected]>
Signed-off-by: Santhosh Kumar K <[email protected]>
|
|
Instead of bloating the defconfig with CONFIG_CMD_*, move J7 devices to
start using TI_COMMON_CMD_OPTIONS.
Signed-off-by: Neha Malcom Francis <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Make the raw-mode options depend on SPL_SYS_MMCSD_RAW_MODE in a more
direct way. This makes it easier to understand the options with
'make menuconfig'.
There are three different ways of specifying the offset:
- sector offset
- partition number
- partition type
So make these a choice, so it is more obvious what is going on.
Update existing boards to enable SPL_SYS_MMCSD_RAW_MODE where needed.
Reviewed-by: Sean Anderson <[email protected]>
Reviewed-by: Quentin Schulz <[email protected]>
Signed-off-by: Simon Glass <[email protected]>
|
|
This is called to set fdtfile based on evm.c code calling ti_set_fdt_env.
Signed-off-by: Manorit Chawdhry <[email protected]>
|
|
Introduce the initial configs needed to support the J722S SoC family.
Signed-off-by: Vaishnav Achath <[email protected]>
Signed-off-by: Jayesh Choudhary <[email protected]>
|
