| Age | Commit message (Collapse) | Author |
|---|
|
This platform enables CONFIG_BOARD_EARLY_INIT_F and then has a
do-nothing board_early_init_f function. Change to not enabling the
option and so not needing an empty function.
Signed-off-by: Tom Rini <[email protected]>
|
|
Resync all defconfig files using qconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Resync all defconfig files using qconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Rename the variable and add ENV_ prefix, so that all configuration
options which are related to environment would have an CONFIG_ENV_
prefix. No functional change.
Reviewed-by: Tom Rini <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
|
|
Tom Rini <[email protected]> says:
In a private thread, Simon asked about what's needed to get PowerPC
migrated to DM_SERIAL. I went and took a look, and to complete the
entire DM_SERIAL migration (excluding SPL/TPL) we're actually nearly
there. This series first migrates PowerPC (and some NXP Layerscape
boards that share history more clearly with PowerPC parts), with the
biggest change being to make sure we still use the correct legacy
drivers in SPL/TPL (where SPL is extremely constrained). With that out
of the way, I looked at what was left. With two exceptions, it's
platforms which can be trivially enabled for conversion, and so we do
that.
Link: https://lore.kernel.org/r/[email protected]
|
|
This converts almost all of the remaining non-DM_SERIAL users to enable
DM_SERIAL. These are platforms where there have long been other SoC
boards that have switched and so it's been a matter of inertia keeping
these from being converted. Do so now.
Signed-off-by: Tom Rini <[email protected]>
|
|
Resync all defconfig files using qconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
At present there is a hex value SPL_STACK which both determines whether
SPL has its own initial stack and the hex value of that stack.
Split off the former into SPL_HAVE_INIT_STACK with SPL_STACK depending
on that and only providing the latter.
Signed-off-by: Simon Glass <[email protected]>
[trini: Resync defconfig files]
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Make the raw-mode options depend on SPL_SYS_MMCSD_RAW_MODE in a more
direct way. This makes it easier to understand the options with
'make menuconfig'.
There are three different ways of specifying the offset:
- sector offset
- partition number
- partition type
So make these a choice, so it is more obvious what is going on.
Update existing boards to enable SPL_SYS_MMCSD_RAW_MODE where needed.
Reviewed-by: Sean Anderson <[email protected]>
Reviewed-by: Quentin Schulz <[email protected]>
Signed-off-by: Simon Glass <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
The help for CONFIG_MTD explains that it needs to be enabled for various
things like NAND, etc to be available. It however then doesn't enforce
this dependency and so if you have none of these systems present you
still need to disable a number of options. Fix this by making places
that select/imply one type of flash, but did not do the same, also do
this for "MTD". Make boards which hadn't been enabling MTD already but
need it now, do so. In a few places, disable CONFIG_CMD_MTDPARTS as it
wasn't previously enabled but was now being implied.
Signed-off-by: Tom Rini <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
We like to put the SPL first so it is clear that it relates to SPL. Rename
various malloc-related options which have crept in, to stick to this
convention.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Marcel Ziswiler <[email protected]>
Reviewed-by: Martyn Welch <[email protected]>
Reviewed-by: Svyatoslav Ryhel <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Signed-off-by: Tom Rini <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_SYS_MONITOR_LEN
To do this, we set a default of 0 for everyone because there are a
number of cases where we define CONFIG_SYS_MONITOR_LEN but the only
impact is that we set TOTAL_MALLOC_LEN to be CONFIG_SYS_MALLOC_LEN +
CONFIG_ENV_SIZE, so we must continue to allow all boards to set this
value. Update the SPL code to use 200 KB as the default raw U-Boot size
directly, if we don't have a real CONFIG_SYS_MONITOR_LEN value.
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
The current name is inconsistent with SPL which uses CONFIG_SPL_TEXT_BASE
and this makes it imposible to use CONFIG_VAL().
Rename it to resolve this problem.
Signed-off-by: Simon Glass <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Initial commit of Librem5 u-boot and SPL
Signed-off-by: Angus Ainslie <[email protected]>
Co-developed-by: Sebastian Krzyszkowiak <[email protected]>
Signed-off-by: Sebastian Krzyszkowiak <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
