| Age | Commit message (Collapse) | Author |
|---|
|
mx7dsabresd_secure_defconfig was introduced to allow booting NXP kernel
that has CAAM support and needs to boot in secure mode.
Instead of keeping two different config targets for the same board,
remove mx7dsabresd_secure_defconfig and select
CONFIG_ARMV7_BOOT_SEC_DEFAULT inside mx7dsabresd_defconfig so that
this target could be used to boot both mainline and the vendor kernel.
This makes maintenance task easier and avoid potentially confusion
for the end user.
Signed-off-by: Fabio Estevam <[email protected]>
Acked-by: Bryan O'Donoghue <[email protected]>
|
|
Migrate the CONFIG_FSL_ESDHC option to Kconfig.
Signed-off-by: Mario Six <[email protected]>
|
|
On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
values into the defconfig and removing them from the headers.
I did not attempt to add more default values in and for now will leave
that to maintainers.
Signed-off-by: Tom Rini <[email protected]>
|
|
Enable UHS and HS200 for mx7dsabresd.
Read Speed improvement:
Kingston SD10VG2/16GB SDHC 3.0 card
22.2MB/s -> 73.7MB/s
eMMC5.0 MTFC8GACAEAM:
68MB/s -> 87MB/s
Signed-off-by: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Jaehoon Chung <[email protected]>
|
|
In order to provide a consistent user experience for imx board users,
remove the custom CONFIG_BOOTDELAY values from defconfig files, so that
all boards can use the default two second delay.
Signed-off-by: Fabio Estevam <[email protected]>
Reviewed-by: Lukasz Majewski <[email protected]>
|
|
|
|
When CONFIG_DM_MMC=y, CONFIG_BLK should be selected, otherwise the
SD/eMMC card cannot be used.
Also, select CONFIG_DM_USB=y when CONFIG_USB=y to avoid build failure.
Tested on mx6slevk, mx7dsabresd and mx6ullevk.
Signed-off-by: Fabio Estevam <[email protected]>
Reviewed-by: Jaehoon Chung <[email protected]>
Tested-by: Adam Ford <[email protected]>
Tested-by: Sébastien Szymanski <[email protected]>
Tested-by: Jagan Teki <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Having this as a 'default y' is rather annoying because it doesn't
actually compile unless other options are defined in the board header:
../cmd/bootm.c: In function 'do_imls_nor':
../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {
Make it 'default n' so people who develop new boards that start from a
blank defconfig have one less compilation failure to debug.
Signed-off-by: Tuomas Tynkkynen <[email protected]>
|
|
The g_dnl USB settings for the vendor ID, product ID and manufacturer are
actually common settings that can and should be shared by all the gadgets.
Make them common by renaming them, and convert all the users.
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Lukasz Majewski <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
|
|
This migrates ASIX, ASIX88179, MCS7830, RTL8152 and SMSC95XX to Kconfig.
Update defconfigs.
Signed-off-by: Chris Packham <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
CONFIG_USB_HOST_ETHER is the framework that the drivers are dependent on
USB_HOST_ETHER. Use this as a menu and move the existing LAN75XX and
LAN78XX options under new menu. Finally update the defconfigs that need
CONFIG_USB_HOST_ETHER.
Signed-off-by: Chris Packham <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Now that the driver supports it, move these boards over to use driver
model fully for MMC.
Signed-off-by: Simon Glass <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Signed-off-by: Alexandru Gagniuc <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
mx7dsabresd_secure_defconfig was not updated after moving to DM.
Signed-off-by: Stefano Babic <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_CMD_BMP
Signed-off-by: Simon Glass <[email protected]>
[trini: Add depends on LCD || DM_VIDEO || VIDEO]
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_CMD_BMODE
Signed-off-by: Simon Glass <[email protected]>
[trini: Make this default y and depend on mx5/6/7]
Signed-off-by: Tom Rini <[email protected]>
|
|
This option should not really be user selectable. Note that on PowerPC
we currently only need BOARD_LATE_INIT when CHAIN_OF_TRUST is enabled so be
conditional on that.
Signed-off-by: Tom Rini <[email protected]>
Acked-by: Masahiro Yamada <[email protected]> (for UniPhier)
|
|
Cc: Tom Rini <[email protected]>
Signed-off-by: Jagan Teki <[email protected]>
|
|
Generated by "tools/moveconfig -s".
This will make config moves easier.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Enable the escpi3 nets attached to the mikroBUS slot
on the i.MX7 Sabre evalution board. Also enble the SPI flash
commands to work with the "flash click" board.
This is V2 of this patch with changes recommended by the maintainer
CC: Jagan Teki <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_SYS_CONSOLE_IS_IN_ENV
CONFIG_CONSOLE_MUX
Signed-off-by: Simon Glass <[email protected]>
[trini: Re-order, re-migrate]
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_VIDEO
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
Introduce a hidden USB_FUNCTION_DFU Kconfig option and select it for
CMD_DFU (as we must have the DFU command enabled to do anything DFU).
Make all of the entries in drivers/dfu/Kconfig depend on CMD_DFU and add
options for all of the back end choices that DFU can make use of.
Cc: Lukasz Majewski <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Acked-by: Lukasz Majewski <[email protected]>
|
|
In some cases we were missing CONFIG_USB=y so enable that when needed.
Reviewed-by: Masahiro Yamada <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Signed-off-by: Tom Rini <[email protected]>
|
|
There is no need for introducing MX7_SEC, as there is the
CONFIG_ARMV7_BOOT_SEC_DEFAULT option for this purpose.
Switch to CONFIG_ARMV7_BOOT_SEC_DEFAULT and get rid of
MX7_SEC.
Tested by booting a 4.1.15 NXP kernel with mx7dsabresd_secure_defconfig
target.
Signed-off-by: Fabio Estevam <[email protected]>
Acked-by: Stefan Agner <[email protected]>
|
|
After moving CONFIG_USB_EHCI_MX7 to Kconfig,
the flag must be set in defconfig for mx7dsabresd.
It is already for the not secure config, it is
missing in the secure configuration.
Signed-off-by: Stefano Babic <[email protected]>
CC: Fabio Estevam <[email protected]>
Tested-by: Fabio Estevam <[email protected]>
|
|
Booting a NXP kernel with mainline U-boot leads to the following kernel
crash:
caam: probe of 30900000.caam failed with error -11
Unable to handle kernel NULL pointer dereference at virtual address 00000004
pgd = 80004000
[00000004] *pgd=00000000
Internal error: Oops: 805 [#1] PREEMPT SMP ARM
This happens because NXP kernel expects MX7 to boot in secure mode,
so introduce mx7dsabresd_secure_defconfig that selects CONFIG_MX7_SEC
and allows booting a NXP provided kernel successfully.
Signed-off-by: Fabio Estevam <[email protected]>
|
