| Age | Commit message (Collapse) | Author |
|---|
|
Resync all defconfig files using qconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
The commit c69103218ee4 ("i2c: mxc_i2c: add DM_FLAG_PRE_RELOC flag")
has enabled by default the i2c initialization in the pre-relocation
phase.
It turned out that vf610 based boards had too small SYS_MALLOC_F_LEN
pool size.
As a solution the explicit value of CONFIG_SYS_MALLOC_F_LEN for all
vf610 based boards has been removed from their configs.
Instead, the default value of 0x2000 is now used, which causes boards
to work correctly again. This approach has been tested on BK4 device.
Signed-off-by: Lukasz Majewski <[email protected]>
|
|
Rename the variable and add ENV_ prefix, so that all configuration
options which are related to environment would have an CONFIG_ENV_
prefix. No functional change.
Reviewed-by: Tom Rini <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
|
|
Rename the variable and add ENV_ prefix, so that all configuration
options which are related to environment would have an CONFIG_ENV_
prefix. No functional change.
Signed-off-by: Marek Vasut <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
The current name is inconsistent with SPL which uses CONFIG_SPL_TEXT_BASE
and this makes it imposible to use CONFIG_VAL().
Rename it to resolve this problem.
Signed-off-by: Simon Glass <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
The "autoload" environment variable is always checked with env_get_yesno
as it can be set to any form of no. The default behavior of
env_get_yesno is to return -1 on variables that are not set, which acts
as true in general (we test for non-zero return). To convert
CONFIG_SYS_AUTOLOAD to Kconfig, given that it was almost always used to
set autoload to no, first rename to CONFIG_SYS_DISABLE_AUTOLOAD for
consistency sake. Then, make it so that if enabled we set autoload=0 in
the default environment. Migrate all platforms which set
CONFIG_SYS_AUTOLOAD to non-true or that set autoload to false in their
default environment to using CONFIG_SYS_DISABLE_AUTOLOAD
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_SYS_CBSIZE
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_SYS_PBSIZE
Signed-off-by: Tom Rini <[email protected]>
|
|
The most commonly used value today is 0x2000 and not 0x400. Rework the
Kconfig logic to use this more frequently used value as the default.
Cc: Andrew F. Davis <[email protected]>
Cc: Alex Nemirovsky <[email protected]>
Cc: Alexey Brodkin <[email protected]>
Cc: Alison Wang <[email protected]>
Cc: Anastasiia Lukianenko <[email protected]>
Cc: Andes <[email protected]>
Cc: Andre Przywara <[email protected]>
Cc: Bharat Gooty <[email protected]>
Cc: David Lechner <[email protected]>
Cc: Dzmitry Sankouski <[email protected]>
Cc: Enric Balletbo i Serra <[email protected]>
Cc: Eugeniy Paltsev <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Gerald Kerma <[email protected]>
Cc: Gregory CLEMENT <[email protected]>
Cc: Holger Brunck <[email protected]>
Cc: Jaehoon Chung <[email protected]>
Cc: Jassi Brar <[email protected]>
Cc: Kristian Amlie <[email protected]>
Cc: Krzysztof Kozlowski <[email protected]>
Cc: Liviu Dudau <[email protected]>
Cc: Luka Perkov <[email protected]>
Cc: Lukasz Majewski <[email protected]>
Cc: Marek Vasut <[email protected]>
Cc: Masami Hiramatsu <[email protected]>
Cc: Matthias Brugger <[email protected]>
Cc: Max Filippov <[email protected]>
Cc: Michael Walle <[email protected]>
Cc: Michal Simek <[email protected]>
Cc: Minkyu Kang <[email protected]>
Cc: Nikita Kiryanov <[email protected]>
Cc: Nobuhiro Iwamatsu <[email protected]>
Cc: Oleksandr Andrushchenko <[email protected]>
Cc: Otavio Salvador <[email protected]>
Cc: Patrice Chotard <[email protected]>
Cc: Paul Burton <[email protected]>
Cc: Paul Kocialkowski <[email protected]>
Cc: Priyanka Jain <[email protected]>
Cc: Rajesh Bhagat <[email protected]>
Cc: Rayagonda Kokatanur <[email protected]>
Cc: Sergey Temerkhanov <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Stefan Bosch <[email protected]>
Cc: Stephan Gerhold <[email protected]>
Cc: Tetsuyuki Kobayashi <[email protected]>
Cc: Thomas Chou <[email protected]>
Cc: Thomas Fitzsimmons <[email protected]>
Cc: Thomas Weber <[email protected]>
Cc: Tony Dinh <[email protected]>
Cc: Trevor Woerner <[email protected]>
Cc: Vitaly Andrianov <[email protected]>
Cc: Vladimir Zapolskiy <[email protected]>
Cc: liuhao <[email protected]>
Cc: lixinde <[email protected]>
Cc: shuyiqi <[email protected]>
Cc: weichangzheng <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Thomas Chou <[email protected]>
Reviewed-by: Masami Hiramatsu <[email protected]>
Reviewed-by: Tony Dinh <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
Reviewed-by: Kristian Amlie <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_BOARD_SIZE_LIMIT
To do this, introduce CONFIG_HAS_BOARD_SIZE_LIMIT.
Signed-off-by: Tom Rini <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_USE_BOOTCOMMAND
CONFIG_BOOTCOMMAND
CONFIG_RAMBOOTCOMMAND
CONFIG_NFSBOOTCOMMAND
Signed-off-by: Tom Rini <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_SYS_NAND_ONFI_DETECTION
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_SYS_MALLOC_LEN
Signed-off-by: Tom Rini <[email protected]>
Acked-by: Sean Anderson <[email protected]>
Reviewed-by: Rick Chen <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_SKIP_LOWLEVEL_INIT
CONFIG_SKIP_LOWLEVEL_INIT_ONLY
In order to do this, we need to introduce SPL and TPL variants of these
options so that we can clearly disable these options only in SPL in some
cases, and both instances in other cases.
Signed-off-by: Tom Rini <[email protected]>
|
|
- Provide a default Kconfig value of the default script
- Largely continue to define this via the board Kconfig file
- For the boards that select a script based on defconfig rather than
TARGET, keep this within the defconfig.
Signed-off-by: Tom Rini <[email protected]>
|
|
Now that we have consistent usage, migrate this symbol to Kconfig.
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Rick Chen <[email protected]>
|
|
- Rename usages of CONFIG_SYS_DEF_EEPROM_ADDR to CONFIG_SYS_I2C_EEPROM_ADDR
based on current usage.
- Convert CONFIG_SYS_I2C_EEPROM_ADDR, CONFIG_SYS_I2C_EEPROM_ADDR_LEN,
CONFIG_SYS_I2C_EEPROM_BUS, CONFIG_CONFIG_SYS_EEPROM_SIZE
CONFIG_SYS_EEPROM_PAGE_WRITE_BITS and CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS
to Kconfig. We move these symbols around a bit and add appropriate
dependencies to them. In some cases, we now add a correct default value
as well.
Signed-off-by: Tom Rini <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_ENV_OVERWRITE
Signed-off-by: Adam Ford <[email protected]>
[trini: Rerun migration, remove some comments]
Signed-off-by: Tom Rini <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Move below defines which are used by mtest utility to Kconfig.
CONFIG_SYS_MEMTEST_START
CONFIG_SYS_MEMTEST_END
Signed-off-by: Ashok Reddy Soma <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
[trini: Fix kmcoge5ne board, re-run migration as well]
Signed-off-by: Tom Rini <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
In some files, options of CMD_NAND are selected but not the command
itself. Fix this inconsistency.
Signed-off-by: Miquel Raynal <[email protected]>
Reviewed-by: Boris Brezillon <[email protected]>
|
|
Both symbols must be enabled when there is a raw NAND driver
selected. Also enable them when CONFIG_CMD_NAND is selected to avoid
breaking things when we'll further rework the MTD dependency
description.
Signed-off-by: Miquel Raynal <[email protected]>
Reviewed-by: Boris Brezillon <[email protected]>
[trini: Rebase and migrate a few more boards here]
Signed-off-by: Tom Rini <[email protected]>
|
|
CONFIG_MTD must be reserved for the MTD core. Like any other
subsystem, prefix the symbol by DM when it comes to DM support.
Signed-off-by: Miquel Raynal <[email protected]>
Reviewed-by: Boris Brezillon <[email protected]>
[trini: Add Kconfig files]
Signed-off-by: Tom Rini <[email protected]>
|
|
Add more clarity by changing the Kconfig entry name.
Signed-off-by: Miquel Raynal <[email protected]>
[trini: Re-run migration, update a few more cases]
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Boris Brezillon <[email protected]>
|
|
- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.
Cc: Wolfgang Denk <[email protected]>
Cc: Joe Hershberger <[email protected]>
Cc: Patrick Delaunay <[email protected]>
Cc: [email protected]
Signed-off-by: Tom Rini <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
Reviewed-by: Simon Goldschmidt <[email protected]>
|
|
Today in initr_reloc_global_data() we use some non-obvious tests to
determine if we need to relocate the env_addr within gd or not. In
order to facilitate migration of other symbols to Kconfig we need to
introduce a new symbol for this particular use case.
Cc: Wolfgang Denk <[email protected]>
Cc: Joe Hershberger <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Move this symbol to Kconfig. As part of this we can drop a UBI-specific
symbol that was a stop-gap for not having this particular symbol in
Kconfig.
Signed-off-by: Tom Rini <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Converted to use fsl_esdhc_imx for i.MX platforms.
Signed-off-by: Yangbo Lu <[email protected]>
Tested-by: Steffen Dirkwinkel <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
Reviewed-by: Lukasz Majewski <[email protected]>
Reviewed-by: Martyn Welch <[email protected]>
Acked-by: Jason Liu <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Commit d397f7c45b0b ("net: phy: micrel: Separate KSZ9000 drivers from
KSZ8000 drivers") separated the KSZ8xxx and KSZ90x1 drivers and warns
that you shouldn't select both of them due to a device ID clash between
the KSZ9021 and the KS8721, asserting that "it is highly unlikely for a
system to contain both a KSZ8000 and a KSZ9000 PHY". Unfortunately
boards like the SAMA5D3xEK do contain both types of PHY, but fortunately
the Linux Micrel PHY driver provides a solution by using different PHY
ID and mask values to distinguish these chips.
This commit contains the following changes:
- The PHY ID and mask values for the KSZ9021 and the KS8721 now match
those used by the Linux driver.
- The warnings about not enabling both drivers have been removed.
- The description for PHY_MICREL_KSZ8XXX has been corrected (these are
10/100 PHYs, not GbE PHYs).
- PHY_MICREL_KSZ9021 and PHY_MICREL_KSZ9031 no longer select PHY_GIGE
since this is selected by PHY_MICREL_KSZ90X1.
- All of the relevant defconfig files have been updated now that
PHY_MICREL_KSZ8XXX does not default to 'Y'.
Signed-off-by: James Byrne <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
While commit 3e020f03e94f ("driver: misc: add MXC_OCOTP Kconfig entry")
introduced a Kconfig entry it did not actually migrate all
configurations to using it.
As CONFIG_MXC_OCOTP was in mx{6/7}_common.h enable it by default on
those architectures. Additionally, also enable it on ARCH_IMX8M and
ARCH_VF610 where all current members enabled it through their legacy
configuration header files.
Signed-off-by: Marcel Ziswiler <[email protected]>
Reviewed-by: Lukasz Majewski <[email protected]>
|
|
This commit updates BK4's and PCM052's config files to support as much
as possible device tree and model in u-boot.
Moreover, remove CONFIG_* from pcm052.h (as those are now in
bk4|pcm052_defconfig)
Signed-off-by: Lukasz Majewski <[email protected]>
|
|
This commit provides update and renames the bk4r1.dts to vf610-bk4r1.dts
file with more on SoC HW description.
The pcm052.dts has been renamed to vf610-pcm052.dts as well.
Moreover, a new vf610-pcm052.drsi file has been introduced
to reuse the common code between devices based on Phytec's
pcm052 modules.
Ported from Linux kernel - v4.20 (tag)
Signed-off-by: Lukasz Majewski <[email protected]>
|
