| Age | Commit message (Collapse) | Author |
|---|
|
Resync all defconfig files using qconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
These are common for all K3 based boards. Add the common values as
defaults and remove from each board defconfig.
Signed-off-by: Andrew Davis <[email protected]>
Reviewed-by: Bryan Brattlof <[email protected]>
|
|
Enable CONFIG_SPL_SYS_MMCSD_RAW_MODE and set the offset address to
boot from raw addresses instead of a FAT partition.
Signed-off-by: Daniel Schultz <[email protected]>
Signed-off-by: Wadim Egorov <[email protected]>
Acked-by: Anshul Dalal <[email protected]>
|
|
Commit 86acdce2ba88 ("common: add config for board_init() call")
introduced CONFIG_BOARD_INIT option. This option can be disabled for the
boards where board_init() function is not needed. Remove empty
board_init() calls for all boards where it's possible, and disable
CONFIG_BOARD_INIT in all related defconfigs.
This cleanup was made semi-automatically using these scripts: [1].
No functional change, but the binary size for the modified boards is
reduced a bit.
[1] https://github.com/joe-skb7/uboot-convert-scripts/tree/master/remove-board-init
Signed-off-by: Sam Protsenko <[email protected]>
Tested-by: Adam Ford <[email protected]> #imx8mm_beacon
Tested-by: Bryan Brattlof <[email protected]>
Acked-by: Peng Fan <[email protected]> #NXP boards
|
|
Rename the variable and add ENV_ prefix, so that all configuration
options which are related to environment would have an CONFIG_ENV_
prefix. No functional change.
Use ENV_MMC_EMMC_HW_PARTITION to clarify this is the eMMC hardware
partition selector, not a software partition table entry selector.
Retain the ENV_MMC_ prefix to make it easier to search for all the
SD/MMC related ENV options. Update the help text accordingly.
Signed-off-by: Marek Vasut <[email protected]>
|
|
Rename the variable and add ENV_ prefix, so that all configuration
options which are related to environment would have an CONFIG_ENV_
prefix. No functional change.
Reviewed-by: Tom Rini <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
|
|
SPL_TEXT_BASE is used as the load address for the main domain SPL on k3
platforms.
Since the config value is the same for every board, this patch sets the
value 0x80080000 as default for all 64-bit ARCH_K3, 0x43c00000 as
default for the R5 cores and deletes the instances of SPL_TEXT_BASE in
individual defconfigs.
Signed-off-by: Anshul Dalal <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Judith Mendez <[email protected]> says:
Some K3 devices like am62x and am64x have a M4 processor in the MCU
voltage domain. This patch series introduces remoteproc M4 driver which
will be used to load firmware into and start the M4 remote core.
This series also adds support for R5F cores on am64x SoCs in patch 2 and
sets up environment to load FW in remote cores in patch 3,4,5.
This patch series also enables remoteproc drivers by default as per what
remoteproc sybsystem is supported per SoC, thus all remoteproc options
are now deleted in configs/* since they are no longer required.
This patch series was tested on am64x EVM, am62x SK, am62ax SK,
am62px SK boards.
Any additional tested by's are welcome since I was not able to
test any additional boards.
Tested by running the following commands in u-boot prompt:
=> setenv dorprocboot 1
=> run boot_rprocs
Link: https://lore.kernel.org/r/[email protected]
|
|
Add support for PHYTEC phyCORE-AM62A7 SoM.
Supported features:
- 2GB LPDDR4 RAM
- eMMC
- External SD
- Ethernet
- debug UART
Signed-off-by: Garrett Giordano <[email protected]>
Reviewed-by: Wadim Egorov <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Reviewed-by: Bryan Brattlof <[email protected]>
|
