| Age | Commit message (Collapse) | Author |
|---|
|
This board is entirely supported by the generic arch code and DTS. The
board code used to handle turning on the vbus regulator, however this is
now handled via DT.
With this, the board specific defconfig is also no longer needed, so
drop it as well.
Reviewed-by: Neil Armstrong <[email protected]>
Reviewed-by: Sumit Garg <[email protected]>
Tested-by: Sumit Garg <[email protected]> #qcs404
Signed-off-by: Caleb Connolly <[email protected]>
|
|
Historically, Qualcomm boards have relied on heavy hardcoding in U-Boot,
in many cases to the specific SoC but also to the board itself (e.g.
memory map). This has been largely resolved by modernising the Qualcomm
drivers in U-Boot, however the board code still largely follows this
model.
This patch removes the board specific memory maps and duplicated board
init code, replacing it with generic init code.
The memory map is now built at runtime based on data read from DT, this
allows for the memory map to be provided without having to recompile
U-Boot. Support is also added for booting with appended DTBs, so that
the first-stage bootloader can populate the memory map for us.
The sdm845 specific init code is dropped entirely, it set an environment
variable depending on if a button was pressed, but this variable wasn't
used in U-Boot, and could be written to use the button command instead.
The KASLR detection is also dropped as with appended dtb, the kaslr seed
can be read directly from the DTB passed to U-Boot.
A new qcom_defconfig is added, with the aim of providing a generic
U-Boot configuration that will work on as many Qualcomm boards as
possible. It replaces the defconfig files for the Dragonboard 845c,
Galaxy S9, and QCS404 EVB. For now the db410c and 820c are excluded as
they still have some board code left.
Similarly, the config headers for db845c, starqltechn, and qcs404-evb
are replaced by a single qcom header.
The previously db410c-specific board_usb_init() function is made to be
generic and is added to mach-snapdragon. While we lack proper modelling
for USB configuration, using a well-known named pinctrl state is a
reasonably generic middleground, and works using upstream DT. This
function will do nothing unless the USB node has a pinctrl state named
"device", in which case it will be set when entering USB peripheral
mode.
Reviewed-by: Neil Armstrong <[email protected]>
Reviewed-by: Sumit Garg <[email protected]>
Tested-by: Sumit Garg <[email protected]> #qcs404
Signed-off-by: Caleb Connolly <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Signed-off-by: Sumit Garg <[email protected]>
|
|
As explained by Philippe Schenker, I was misinterpreting what happened
in the case where we do not set LMB_USE_MAX_REGIONS and so had
re-introduced the problem I was attempting to more widely resolve.
This reverts commit 007ae5d108a37564905ea1588cb279f3a522cc3d.
Reported-by: Philippe Schenker <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
The LMB code allows for picking a hard limit on the number of regions it
can know of, or to dynamically allocate these regions. The reason for
this choice is to allow for the compiler to perform a size optimization
in the common case. This optimization however, is very small, ranging
from 196 bytes to 15 bytes saved, or in some cases, being larger. Now
that we also have more regions covered by LMB (in order to protect
various parts of our self at run time), the default of 8 is also much
easier to hit and leads to non-obvious error messages (which imply that
an area is protected, not that we're out of areas to add to the list).
Switch to the dynamic use as the default.
Signed-off-by: Tom Rini <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Enable USB config options along with its dependencies like PHY, RESET,
PMIC GPIO etc. config options.
Signed-off-by: Sumit Garg <[email protected]>
|
|
Add support for Qualcomm QCS404 SoC based evaluation board.
Features:
- Qualcomm Snapdragon QCS404 SoC
- 1GiB RAM
- 8GiB eMMC, uSD slot
U-boot is chain loaded by ABL in 64-bit mode as part of boot.img.
For detailed build and boot instructions, refer to
doc/board/qualcomm/qcs404.rst.
Signed-off-by: Sumit Garg <[email protected]>
|
