| Age | Commit message (Collapse) | Author |
|---|
|
Rename the variable and add ENV_ prefix, so that all configuration
options which are related to environment would have an CONFIG_ENV_
prefix. No functional change.
Reviewed-by: Tom Rini <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
|
|
Prepare the introduction of the lwIP (lightweight IP) TCP/IP stack by
adding a new net/lwip/ directory and the NET_LWIP symbol. Network
support is either NO_NET, NET (legacy stack) or NET_LWIP. Subsequent
commits will introduce the lwIP code, re-work the NETDEVICE integration
and port some of the NET commands and features to lwIP.
SPL_NET cannot be enabled when NET_LWIP=y. SPL_NET pulls some symbols
that are part of NET (such as arp_init(), arp_timeout_check(),
arp_receive(), net_arp_wait_packet_ip()). lwIP support in SPL may be
added later.
Similarly, DFU_TFTP and FASTBOOT are not compatible with NET_LWIP
because of dependencies on net_loop(), tftp_timeout_ms,
tftp_timeout_count_max and other NET things. Let's add a dependency on
!NET_LWIP for now.
SANDBOX can select NET_LWIP but doing so will currently disable the eth
dm tests as well as the wget tests which have strong dependencies on the
NET code.
Other adjustments to Kconfig files are made to fix "unmet direct
dependencies detected" for USB_FUNCTION_SDP and CMD_FASTBOOT when
the default networking stack is set to NET_LWIP ("default NET_LWIP"
instead of "default NET" in Kconfig).
The networking stack is now a choice between NO_NET,
NET and NET_LWIP. Therefore '# CONFIG_NET is not set' should be
'CONFIG_NO_NET=y'. Adjust the defconfigs accordingly.
Signed-off-by: Jerome Forissier <[email protected]>
Acked-by: Ilias Apalodimas <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
The help for CONFIG_MTD explains that it needs to be enabled for various
things like NAND, etc to be available. It however then doesn't enforce
this dependency and so if you have none of these systems present you
still need to disable a number of options. Fix this by making places
that select/imply one type of flash, but did not do the same, also do
this for "MTD". Make boards which hadn't been enabling MTD already but
need it now, do so. In a few places, disable CONFIG_CMD_MTDPARTS as it
wasn't previously enabled but was now being implied.
Signed-off-by: Tom Rini <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
None of these platforms enabled a networking devices, and disabled
CMD_NET. Given that we used to gate network support on CMD_NET rather
than NET, we disable CONFIG_NET on these platforms now.
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_SYS_MONITOR_LEN
To do this, we set a default of 0 for everyone because there are a
number of cases where we define CONFIG_SYS_MONITOR_LEN but the only
impact is that we set TOTAL_MALLOC_LEN to be CONFIG_SYS_MALLOC_LEN +
CONFIG_ENV_SIZE, so we must continue to allow all boards to set this
value. Update the SPL code to use 200 KB as the default raw U-Boot size
directly, if we don't have a real CONFIG_SYS_MONITOR_LEN value.
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
The current name is inconsistent with SPL which uses CONFIG_SPL_TEXT_BASE
and this makes it imposible to use CONFIG_VAL().
Rename it to resolve this problem.
Signed-off-by: Simon Glass <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_VIDEO_LOGO_MAX_SIZE
Signed-off-by: Simon Glass <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_USB_GADGET_DWC2_OTG_PHY
Signed-off-by: Tom Rini <[email protected]>
|
|
- In a number of cases, use CONFIG_ARCH_EXYNOS[45] rather than
CONFIG_EXYNOS[45]
- In other cases, test for CONFIG_ARCH_EXYNOS or CONFIG_ARCH_S5PC1XX
- Migrate specific SoC CONFIG values to Kconfig
- Use CONFIG_TARGET_x rather than CONFIG_x
- Migrate other CONFIG_EXYNOS_x symbols to Kconfig
- Reference CONFIG_EXYNOS_RELOCATE_CODE_BASE directly as EXYNOS_RELOCATE_CODE_BASE
- Rename CONFIG_S5P_PA_SYSRAM to CONFIG_SMP_PEN_ADDR to match the rest
of U-Boot usage.
Cc: Minkyu Kang <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
- Make all users of CUSTOM_SYS_INIT_SP_ADDR reference SYS_INIT_SP_ADDR
- Introduce HAS_CUSTOM_SYS_INIT_SP_ADDR to allow for setting the stack
pointer directly, otherwise we use the common calculation.
- On some platforms that were using the standard calculation but did not
set CONFIG_SYS_INIT_RAM_SIZE / CONFIG_SYS_INIT_RAM_ADDR, set them.
- On a small number of platforms that were not subtracting
GENERATED_GBL_DATA_SIZE do so now via the standard calculation.
- CONFIG_SYS_INIT_SP_OFFSET is now widely unused, so remove it from most
board config header files.
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_SYS_PBSIZE
Signed-off-by: Tom Rini <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
The most commonly used value today is 0x2000 and not 0x400. Rework the
Kconfig logic to use this more frequently used value as the default.
Cc: Andrew F. Davis <[email protected]>
Cc: Alex Nemirovsky <[email protected]>
Cc: Alexey Brodkin <[email protected]>
Cc: Alison Wang <[email protected]>
Cc: Anastasiia Lukianenko <[email protected]>
Cc: Andes <[email protected]>
Cc: Andre Przywara <[email protected]>
Cc: Bharat Gooty <[email protected]>
Cc: David Lechner <[email protected]>
Cc: Dzmitry Sankouski <[email protected]>
Cc: Enric Balletbo i Serra <[email protected]>
Cc: Eugeniy Paltsev <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Gerald Kerma <[email protected]>
Cc: Gregory CLEMENT <[email protected]>
Cc: Holger Brunck <[email protected]>
Cc: Jaehoon Chung <[email protected]>
Cc: Jassi Brar <[email protected]>
Cc: Kristian Amlie <[email protected]>
Cc: Krzysztof Kozlowski <[email protected]>
Cc: Liviu Dudau <[email protected]>
Cc: Luka Perkov <[email protected]>
Cc: Lukasz Majewski <[email protected]>
Cc: Marek Vasut <[email protected]>
Cc: Masami Hiramatsu <[email protected]>
Cc: Matthias Brugger <[email protected]>
Cc: Max Filippov <[email protected]>
Cc: Michael Walle <[email protected]>
Cc: Michal Simek <[email protected]>
Cc: Minkyu Kang <[email protected]>
Cc: Nikita Kiryanov <[email protected]>
Cc: Nobuhiro Iwamatsu <[email protected]>
Cc: Oleksandr Andrushchenko <[email protected]>
Cc: Otavio Salvador <[email protected]>
Cc: Patrice Chotard <[email protected]>
Cc: Paul Burton <[email protected]>
Cc: Paul Kocialkowski <[email protected]>
Cc: Priyanka Jain <[email protected]>
Cc: Rajesh Bhagat <[email protected]>
Cc: Rayagonda Kokatanur <[email protected]>
Cc: Sergey Temerkhanov <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Stefan Bosch <[email protected]>
Cc: Stephan Gerhold <[email protected]>
Cc: Tetsuyuki Kobayashi <[email protected]>
Cc: Thomas Chou <[email protected]>
Cc: Thomas Fitzsimmons <[email protected]>
Cc: Thomas Weber <[email protected]>
Cc: Tony Dinh <[email protected]>
Cc: Trevor Woerner <[email protected]>
Cc: Vitaly Andrianov <[email protected]>
Cc: Vladimir Zapolskiy <[email protected]>
Cc: liuhao <[email protected]>
Cc: lixinde <[email protected]>
Cc: shuyiqi <[email protected]>
Cc: weichangzheng <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Thomas Chou <[email protected]>
Reviewed-by: Masami Hiramatsu <[email protected]>
Reviewed-by: Tony Dinh <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
Reviewed-by: Kristian Amlie <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_SYS_MEM_TOP_HIDE
Signed-off-by: Tom Rini <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_CONS_INDEX
CONFIG_DEBUG_UART_CLOCK
CONFIG_FSL_TZPC_BP147
CONFIG_GENERIC_ATMEL_MCI
CONFIG_IDENT_STRING
CONFIG_LIBATA
CONFIG_LNX_KRNL_IMG_TEXT_OFFSET_BASE
CONFIG_LPC32XX_GPIO
CONFIG_MP
CONFIG_MPC8XXX_GPIO
CONFIG_MTD_PARTITIONS
CONFIG_MVGBE
CONFIG_MXC_GPIO
CONFIG_NR_DRAM_BANKS
CONFIG_OF_BOARD_SETUP
CONFIG_OF_STDOUT_VIA_ALIAS
CONFIG_OF_SYSTEM_SETUP
CONFIG_PREBOOT
CONFIG_ROCKCHIP_SERIAL
CONFIG_RTC_ENABLE_32KHZ_OUTPUT
CONFIG_RTC_MV
CONFIG_SCSI_AHCI
CONFIG_SF_DEFAULT_BUS
CONFIG_SF_DEFAULT_CS
CONFIG_SF_DEFAULT_SPEED
CONFIG_SOFT_SPI
CONFIG_SPI_FLASH_EON
CONFIG_SPI_FLASH_MACRONIX
CONFIG_SPI_FLASH_MTD
CONFIG_SPI_FLASH_SPANSION
CONFIG_SPI_FLASH_SST
CONFIG_SPI_FLASH_STMICRO
CONFIG_SUPPORT_RAW_INITRD
CONFIG_SYS_ARCH_TIMER
CONFIG_SYS_BOARD
CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
CONFIG_SYS_DCACHE_OFF
CONFIG_SYS_FDT_SAVE_ADDRESS
CONFIG_SYS_FLASH_CFI
CONFIG_SYS_FSL_ERRATUM_ESDHC135
CONFIG_SYS_HAS_SERDES
CONFIG_SYS_L2CACHE_OFF
CONFIG_SYS_LITTLE_ENDIAN
CONFIG_SYS_LOAD_ADDR
CONFIG_SYS_MMCSD_FS_BOOT_PARTITION
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
CONFIG_SYS_NS16550
CONFIG_SYS_PLLFIN
CONFIG_SYS_SPI_U_BOOT_OFFS
CONFIG_TIMER_SYS_TICK_CH
CONFIG_USB_EHCI_FSL
CONFIG_U_QE
CONFIG_VERSION_VARIABLE
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_USE_BOOTCOMMAND
CONFIG_BOOTCOMMAND
CONFIG_RAMBOOTCOMMAND
CONFIG_NFSBOOTCOMMAND
Signed-off-by: Tom Rini <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_SYS_MALLOC_LEN
Signed-off-by: Tom Rini <[email protected]>
Acked-by: Sean Anderson <[email protected]>
Reviewed-by: Rick Chen <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_SKIP_LOWLEVEL_INIT
CONFIG_SKIP_LOWLEVEL_INIT_ONLY
In order to do this, we need to introduce SPL and TPL variants of these
options so that we can clearly disable these options only in SPL in some
cases, and both instances in other cases.
Signed-off-by: Tom Rini <[email protected]>
|
|
Now that we have consistent usage, migrate this symbol to Kconfig.
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Rick Chen <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
CONFIG_SYS_DFU_MAX_FILE_SIZE to Kconfig
Currently the config options CONFIG_SYS_DFU_DATA_BUF_SIZE and
CONFIG_SYS_DFU_MAX_FILE_SIZE are being set in include/configs/<board>.h
files and also in <board_name>_defconfig files without a Kconfig option. It
is easier for users to set these configs in defconfig files than in config
header files as they are a part of the source code.
Add Kconfig symbols, and update the defconfigs by using tools/moveconfig.py
script.
Suggested-by: Pratyush Yadav <[email protected]>
Signed-off-by: Aswath Govindraju <[email protected]>
Acked-by: Oleksandr Suvorov <[email protected]>
Acked-by: Matthias Brugger <[email protected]>
Acked-by: Lukasz Majewski <[email protected]>
|
|
The "cmd/Kconfig" has a TODO description for CMD_MISC that it should
really be named as CMD_SLEEP. Change it in the whole source tree.
Signed-off-by: Bin Meng <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_ENV_OVERWRITE
Signed-off-by: Adam Ford <[email protected]>
[trini: Rerun migration, remove some comments]
Signed-off-by: Tom Rini <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Like in Linux, just use CONFIG_MTD to compile the MTD stack.
Signed-off-by: Miquel Raynal <[email protected]>
Reviewed-by: Boris Brezillon <[email protected]>
|
|
- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.
Cc: Wolfgang Denk <[email protected]>
Cc: Joe Hershberger <[email protected]>
Cc: Patrick Delaunay <[email protected]>
Cc: [email protected]
Signed-off-by: Tom Rini <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
Reviewed-by: Simon Goldschmidt <[email protected]>
|
|
Today in initr_reloc_global_data() we use some non-obvious tests to
determine if we need to relocate the env_addr within gd or not. In
order to facilitate migration of other symbols to Kconfig we need to
introduce a new symbol for this particular use case.
Cc: Wolfgang Denk <[email protected]>
Cc: Joe Hershberger <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_ARCH_CPU_INIT
Signed-off-by: Adam Ford <[email protected]>
Acked-by: Chris Packham <[email protected]>
Tested-by: Felix Brack <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_MISC_INIT_R
Signed-off-by: Adam Ford <[email protected]>
[trini: Update the defaults logic slightly]
Signed-off-by: Tom Rini <[email protected]>
|
|
Enable the CONFIG_DM_REGULATOR_MAX77686 for using regulator driver.
Signed-off-by: Jaehoon Chung <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Convert CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG to Kconfig
Signed-off-by: Alex Kiernan <[email protected]>
Reviewed-by: Lukasz Majewski <[email protected]>
Reviewed-by: Petr Vorel <[email protected]>
Reviewed-by: Petr Vorel <petr.vorel at gmail.com>
|
|
Enable networking command only when NET is enabled.
And remove selecting NET for CMD_NET
Signed-off-by: Michal Simek <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
A number of platforms include config_distro_defaults.h but do not enable
CONFIG_DISTRO_DEFAULTS. As they plainly intended to, set that flag and
re-sync config files.
Signed-off-by: Tom Rini <[email protected]>
|
|
On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
values into the defconfig and removing them from the headers.
I did not attempt to add more default values in and for now will leave
that to maintainers.
Signed-off-by: Tom Rini <[email protected]>
|
|
config_fallbacks.h had some logic to automatically select
LIB_RAND if RANDOM_UUID or CMD_UUID were set if LIB_HW_RAND wasn't
already selected. By migrating LIB_HW_RAND to Kconfig, we can
remove this check from config_fallbacks.h and put it into Kconfig
Signed-off-by: Adam Ford <[email protected]>
Reviewed-by: Lukasz Majewski <[email protected]>
[trini: Turn into a choice, add NET_RANDOM_ETHADDR]
Signed-off-by: Tom Rini <[email protected]>
|
|
cmd/Makefile has:
ifdef CONFIG_FPGA
obj-$(CONFIG_CMD_FPGA) += fpga.o
endif
which means that if CONFIG_FPGA is not set, CONFIG_CMD_FPGA silently
does nothing. Let's remove that Makefile conditional and instead express
this equivalent dependency in Kconfig, so a lot of redundant
# CONFIG_CMD_FPGA is not set
can be removed from board defconfigs that don't actually have an FPGA.
Signed-off-by: Tuomas Tynkkynen <[email protected]>
|
