| Age | Commit message (Collapse) | Author |
|---|
|
Resync all defconfig files using qconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Francesco Dolcini <[email protected]> says:
Enable standard EFI support for all the arm64 Toradex boards, as
required for booting standard aarch64 Linux distribution, following the
ARM recommendations for SystemReady compliance.
The RTC used on these boards is not currently supported by U-Boot,
therefore it is not enabled at the moment.
Link: https://developer.arm.com/documentation/DUI1101/4-5/Configure-U-Boot-for-SystemReady
Link: https://lore.kernel.org/r/[email protected]
|
|
Enable EFI related options, as suggested for booting standard aarch64
Linux distribution, following the ARM recommendations for SystemReady
compliance [1].
The RTC used on this board is not currently supported by U-Boot,
therefore it is not enabled at the moment.
Link: https://developer.arm.com/documentation/DUI1101/4-5/Configure-U-Boot-for-SystemReady [1]
Signed-off-by: Francesco Dolcini <[email protected]>
|
|
With correct POSIX handling, unquoted empty variables can turn the
expression like
test -n ${fdtfile}
into
test -n
The POSIX handling for single argument `test` evaluates it as true,
so the fallback initialization will be skipped unexpectedly.
Quoting variable expansions in `test` expressions will always result in
correct behavior for empty and non-empty values.
This change was triggered by
commit 8b0619579b22 ("cmd: test: fix handling of single-argument form of test")
The aim is to have a less fragile codebase that is not dependent on a
quirk of the shell implementation.
Use quoted variable expansions in `test` expressions throughout.
Signed-off-by: Franz Schnyder <[email protected]>
Acked-by: Francesco Dolcini <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
These are common for all K3 based boards. Add the common values as
defaults and remove from each board defconfig
Signed-off-by: Andrew Davis <[email protected]>
Reviewed-by: Bryan Brattlof <[email protected]>
|
|
Resync all defconfig files using qconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
USB OS Descriptors are used to install and configure the device without
requiring any user interaction on OS which support them (e.g. Windows).
Enable them in order to improve the user experience when fastboot is used.
Signed-off-by: Emanuele Ghidoli <[email protected]>
|
|
Resync all defconfig files using qconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Commit 86acdce2ba88 ("common: add config for board_init() call")
introduced CONFIG_BOARD_INIT option. This option can be disabled for the
boards where board_init() function is not needed. Remove empty
board_init() calls for all boards where it's possible, and disable
CONFIG_BOARD_INIT in all related defconfigs.
This cleanup was made semi-automatically using these scripts: [1].
No functional change, but the binary size for the modified boards is
reduced a bit.
[1] https://github.com/joe-skb7/uboot-convert-scripts/tree/master/remove-board-init
Signed-off-by: Sam Protsenko <[email protected]>
Tested-by: Adam Ford <[email protected]> #imx8mm_beacon
Tested-by: Bryan Brattlof <[email protected]>
Acked-by: Peng Fan <[email protected]> #NXP boards
|
|
CONFIG_NR_DRAM_BANKS defines the number of DRAM banks on the
device. The default value of NR_DRAM_BANKS for ARCH_K3 is set to 2
(arch/arm/mach-k3/Kconfig:199) but should be 1 for am62x platforms.
This patch updates NR_DRAM_BANKS value for all am62x platforms to 1.
Fixes: 2969ed31b893 ("configs: Add am62x_beagleplay_*_defconfig")
Fixes: 2d257d9279e3 ("configs: Add configs for AM62x SK")
Fixes: 085cd6459dae ("board: phytec: am62x: Add PHYTEC phyCORE-AM62x SoM")
Fixes: 7d1a10659f5b ("board: toradex: add verdin am62 support")
Signed-off-by: Anshul Dalal <[email protected]>
|
|
Enable DM_RNG in U-Boot to populate /chosen/kaslr-seed automatically.
Enable OP-TEE, which supports RNG, to provide entropy.
Signed-off-by: Emanuele Ghidoli <[email protected]>
|
|
Udit Kumar <[email protected]> says:
Many boards based upon K3 ARCH overrides default malloc size to 32MB,
as part of cleanup, add default size of 32MB for K3 ARCH.
Link: https://lore.kernel.org/r/[email protected]
|
|
Use default value of malloc size coming from Kconfig, instead of
board specific override.
Signed-off-by: Udit Kumar <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Rename the variable and add ENV_ prefix, so that all configuration
options which are related to environment would have an CONFIG_ENV_
prefix. No functional change.
Use ENV_MMC_EMMC_HW_PARTITION to clarify this is the eMMC hardware
partition selector, not a software partition table entry selector.
Retain the ENV_MMC_ prefix to make it easier to search for all the
SD/MMC related ENV options. Update the help text accordingly.
Signed-off-by: Marek Vasut <[email protected]>
|
|
Rename the variable and add ENV_ prefix, so that all configuration
options which are related to environment would have an CONFIG_ENV_
prefix. No functional change.
Reviewed-by: Tom Rini <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
|
|
Several Kconfig options are enabled but unused or unnecessary for our
use case. These include features such as SPL FAT support, YMODEM, and
USB keyboard. Some R5-specific configurations are not used at all,
as U-Boot proper is not executed on that core.
Cleaning them up helps reduce build size and simplifies maintenance.
Signed-off-by: Emanuele Ghidoli <[email protected]>
Reviewed-by: Francesco Dolcini <[email protected]>
|
|
SPL_TEXT_BASE is used as the load address for the main domain SPL on k3
platforms.
Since the config value is the same for every board, this patch sets the
value 0x80080000 as default for all 64-bit ARCH_K3, 0x43c00000 as
default for the R5 cores and deletes the instances of SPL_TEXT_BASE in
individual defconfigs.
Signed-off-by: Anshul Dalal <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Judith Mendez <[email protected]> says:
Some K3 devices like am62x and am64x have a M4 processor in the MCU
voltage domain. This patch series introduces remoteproc M4 driver which
will be used to load firmware into and start the M4 remote core.
This series also adds support for R5F cores on am64x SoCs in patch 2 and
sets up environment to load FW in remote cores in patch 3,4,5.
This patch series also enables remoteproc drivers by default as per what
remoteproc sybsystem is supported per SoC, thus all remoteproc options
are now deleted in configs/* since they are no longer required.
This patch series was tested on am64x EVM, am62x SK, am62ax SK,
am62px SK boards.
Any additional tested by's are welcome since I was not able to
test any additional boards.
Tested by running the following commands in u-boot prompt:
=> setenv dorprocboot 1
=> run boot_rprocs
Link: https://lore.kernel.org/r/[email protected]
|
|
Resync all defconfig files using qconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
The current value of CONFIG_FASTBOOT_BUF_ADDR is incorrect for hardware
with 512MB and 1GB of RAM. The RAM address ranges for these devices are:
- 512MB:
- Start: 0x80000000
- End: 0xA0000000
- 1GB:
- Start: 0x80000000
- End: 0xC0000000
The current buffer address makes fastboot downloads work only on
hardware with 2GB of RAM.
To fix this issue:
1. Lower CONFIG_FASTBOOT_BUF_ADDR to 0x88200000. This makes the buffer
to be equal ot CONFIG_SYS_LOAD_ADDR, which is a safe address to
download files using fastboot.
2. Reduce the size of the download buffer to 128MB, avoiding overlaps
with RAMDISK_ADDR_R. This is a good enough value for individual
downloads.
These changes make fastboot downloads work with 512MB and 1GB devices.
Fixes: defe30a78b76 ("verdin-am62: add DFU, USB and UUU fastboot support")
Signed-off-by: Hiago De Franco <[email protected]>
Acked-by: Francesco Dolcini <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Make the raw-mode options depend on SPL_SYS_MMCSD_RAW_MODE in a more
direct way. This makes it easier to understand the options with
'make menuconfig'.
There are three different ways of specifying the offset:
- sector offset
- partition number
- partition type
So make these a choice, so it is more obvious what is going on.
Update existing boards to enable SPL_SYS_MMCSD_RAW_MODE where needed.
Reviewed-by: Sean Anderson <[email protected]>
Reviewed-by: Quentin Schulz <[email protected]>
Signed-off-by: Simon Glass <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Enable USB host as well as USB gadget and DFU support for a53 and r5
configs. Also, enable UUU fastboot support to download files with
the UUU tool from a53.
Additionally, configure usb0 to peripheral mode and add extra
environment for DFU use.
Signed-off-by: Vitor Soares <[email protected]>
Reviewed-by: Francesco Dolcini <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Move verdin-am62 to OF_UPSTREAM:
- handle the fact that dtbs now have a 'ti/' prefix
- imply OF_UPSTREAM
- remove redundant files from arch/arm/dts leaving only the
*-u-boot.dtsi files
- update MAINTAINERS file
Signed-off-by: Marcel Ziswiler <[email protected]>
Reviewed-by: Dhruva Gole <[email protected]>
Reviewed-by: Neha Malcom Francis <[email protected]>
Reviewed-by: Sumit Garg <[email protected]>
|
|
Prepare v2024.04-rc4
|
|
The fixups provided by ft_system_setup() are applicable for all AM62 based
boards. Select this at the target selection level for all AM62 boards and
remove it from any specific defconfig.
Signed-off-by: Andrew Davis <[email protected]>
|
|
There is a default ATF load address that is used for devices that have
ATF running in SRAM. For AM62 and AM62a, ATF runs from DRAM. Instead
of having to override the address in every defconfig, make add a
default for these ATF in DRAM devices.
Signed-off-by: Andrew Davis <[email protected]>
Acked-by: Bryan Brattlof <[email protected]>
Reviewed-by: Neha Malcom Francis <[email protected]>
|
|
Francesco Dolcini <[email protected]> says:
This series fixes two regressions affecting multiple Toradex boards
(i.MX, TI and TEGRA based) and targets the current master, e.g. v2024.04
release.
U-Boot `reset` command is broken on all Tordex i.MX6* based SoMs since
v2023.07, this series fixes it enabling the `wdt-reboot` driver.
Since v2024.04-rc1 reading the Toradex configuration block is not working
properly anymore, the serial number and the hardware version are not read
correctly, preventing the board from functioning correctly (wrong mac address,
wrong DT, ...). This is fixed by reading the config block in `EVT_SETTINGS_R`
and adding a toradex sysinfo driver. In addition to that, we now use a random
mac address in case the config block is invalid.
Reported-by: Sahaj Sarup <[email protected]>
Closes: https://lore.kernel.org/all/CAKZ1LvM45MB8N0CqgU+C7i9=Bjb6kqNTxWo2Tv407HKLWtCMkA@mail.gmail.com/
Reported-by: Marcel Ziswiler <[email protected]>
Closes: https://lore.kernel.org/all/[email protected]/
Reported-by: Francesco Dolcini <[email protected]>
Closes: https://lore.kernel.org/all/ZY2ZDWAQuTlRjV9H@francesco-nb/
|
|
Set CONFIG_NET_RANDOM_ETHADDR=y, which sets random eth address in
case there is no toradex config block programmed.
In case of missing toradex config block the generated mac address was
always the same, linked to serial number 0.
Use random generated mac address instead.
Acked-by: Marcel Ziswiler <[email protected]>
Tested-by: Marcel Ziswiler <[email protected]> # Verdin iMX8M Plus
Signed-off-by: Emanuele Ghidoli <[email protected]>
Signed-off-by: Francesco Dolcini <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Disable CONFIG_SPL_LOAD_FIT_APPLY_OVERLAY, this is not required nor used
on verdin am62, disable it to save precious binary size.
Update defconfig using savedefconfig, this adds CONFIG_OF_LIBFDT_OVERLAY
explicitly.
Signed-off-by: Francesco Dolcini <[email protected]>
Acked-by: Marcel Ziswiler <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <[email protected]>
|
|
This adds initial support for the Toradex Verdin AM62 Quad 1GB WB IT
V1.0A module and subsequent V1.1 launch configuration SKUs. They are
strapped to boot from their on-module eMMC. U-Boot supports booting
from the on-module eMMC only, DFU support is disabled for now due to
missing AM62x USB support.
The device trees were taken straight from Linux v6.5-rc1.
Boot sequence is:
SYSFW ---> R5 SPL (both in tiboot3.bin) ---> ATF (TF-A) ---> OP-TEE
---> A53 SPL (part of tispl.bin) ---> U-boot proper (u-boot.img)
Signed-off-by: Marcel Ziswiler <[email protected]>
Reviewed-by: Nishanth Menon <[email protected]>
|
