| Age | Commit message (Collapse) | Author |
|---|
|
Make the conversion for all existing TI documentation from README to
.rst
Signed-off-by: Neha Malcom Francis <[email protected]>
|
|
Since the commit 1289e96797bf ("sandbox: spi: Drop command-line SPI
option"), "--spi_sf" command line option is no longer supported.
So update the following documents to sync them up with the change.
doc/arch/sandbox.rst
doc/SPI/README.sandbox-spi
Signed-off-by: AKASHI Takahiro <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Now that new SPI NOR layer uses stateless 4 byte opcodes by default,
don't enable SPI_FLASH_BAR. For SPI controllers that cannot support
4-byte addressing, (stm32_qspi.c, fsl_qspi.c, mtk_qspi.c, ich.c,
renesas_rpc_spi.c) add an imply clause to enable SPI_FLASH_BAR so as to
not break functionality.
Signed-off-by: Vignesh R <[email protected]>
Tested-by: Simon Goldschmidt <[email protected]>
Tested-by: Stefan Roese <[email protected]>
Tested-by: Horatiu Vultur <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
Tested-by: Jagan Teki <[email protected]> #zynq-microzed
|
|
SF_DUAL_FLASH claims to enable support for SF_DUAL_STACKED_FLASH and
SF_DUAL_PARALLEL_FLASH. But, in current U-Boot code, grepping for above
enums yield no user and therefore support seems to be incomplete. Remove
these configs so as to avoid confusion.
Signed-off-by: Vignesh R <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
Tested-by: Jagan Teki <[email protected]> #zynq-microzed
|
|
Spelling corrections for (among other things):
* environment
* override
* variable
* ftd (should be "fdt", for flattened device tree)
* embedded
* FTDI
* emulation
* controller
|
|
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).
Signed-off-by: Bin Meng <[email protected]>
Reviewed-by: Heiko Schocher <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Minkyu Kang <[email protected]>
|
|
Add short documentation-alike note on how to use the Altera SPI
driver with the EPCS/EPCQx1 FPGA IP block on SoCFPGA Cyclone V
into doc/SPI/README.altera_spi
Signed-off-by: Marek Vasut <[email protected]>
Cc: Chin Liang See <[email protected]>
Cc: Dinh Nguyen <[email protected]>
Cc: Albert Aribaud <[email protected]>
Cc: Pavel Machek <[email protected]>
Cc: Jagannadha Sutradharudu Teki <[email protected]>
Acked-by: Pavel Machek <[email protected]>
Reviewed-by: Jagannadha Sutradharudu Teki <[email protected]>
|
|
This shows the log obtained while testing qspi on AM437x board.
Signed-off-by: Sourav Poddar <[email protected]>
Reviewed-by: Jagannadha Sutradharudu Teki <[email protected]>
|
|
Updated current SPI subsyetem status.
Signed-off-by: Jagannadha Sutradharudu Teki <[email protected]>
|
|
This patch added support for accessing dual memories in
parallel connection with single chipselect line from controller.
For more info - see doc/SPI/README.dual-flash
Signed-off-by: Jagannadha Sutradharudu Teki <[email protected]>
|
|
This patch added support for accessing dual memories in
stacked connection with single chipselect line from controller.
For more info - see doc/SPI/README.dual-flash
Signed-off-by: Jagannadha Sutradharudu Teki <[email protected]>
|
|
The Faraday FTSSP010 is a multi-function controller
which supports I2S/SPI/SSP/AC97/SPDIF. However This
patch implements only the SPI mode.
NOTE:
The DMA and CS/Clock control logic has been altered
since hardware revision 1.19.0. So this patch
would first detects the revision id of the underlying
chip, and then switch to the corresponding software
control routines.
Signed-off-by: Kuo-Jung Su <[email protected]>
Signed-off-by: Jagannadha Sutradharudu Teki <[email protected]>
CC: Tom Rini <[email protected]>
|
|
This patch adds a driver for Renesas SoC's Quad SPI bus.
This supports with 8 bits per transfer to use with SPI flash.
Signed-off-by: Kouei Abe <[email protected]>
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
Signed-off-by: Jagannadha Sutradharudu Teki <[email protected]>
|
|
This adds a SPI flash driver which simulates SPI flash clients.
Currently supports the bare min that U-Boot requires: you can
probe, read, erase, and write. Should be easy to extend to make
it behave more exactly like a real SPI flash, but this is good
enough to merge now.
[email protected] added a README and tidied up code a little.
Added a required map_sysmem() for sandbox.
Signed-off-by: Mike Frysinger <[email protected]>
Signed-off-by: Simon Glass <[email protected]>
|
|
Updated SPI/status.txt, with memory_map and TODO.
Signed-off-by: Jagannadha Sutradharudu Teki <[email protected]>
|
|
Contains documentation and testing details for qspi flash
interface.
Signed-off-by: Sourav Poddar <[email protected]>
Reviewed-by: Jagannadha Sutradharudu Teki <[email protected]>
|
|
doc/SPI/status.txt added to track the u-boot SPI subsystem status.
Signed-off-by: Jagannadha Sutradharudu Teki <[email protected]>
|
