| Age | Commit message (Collapse) | Author |
|---|
|
Fastboot currently supports MMC and NAND flash devices. Similarly,
extend the support to SPI flash memories.
Note that in this initial implementation, partitions on the device are
not supported yet, but raw partitions can be set in U-Boot environment.
To define a raw partition descriptor, add an environment variable
similar to the MMC case:
```
fastboot_raw_partition_<raw partition name>=<offset> <size>
```
for example:
```
fastboot_raw_partition_boot=0x0 0x1000000
```
Signed-off-by: Ariel D'Alessandro <[email protected]>
Reviewed-by: Mattijs Korpershoek <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-dfu
u-boot-dfu-20240419
- new "fastboot oem board" command
|
|
enabled""
As reported by Jonas Karlman this series breaks booting on some AArch64
platforms with common use cases. For now the best path forward is to
revert the series.
This reverts commit 777c28460947371ada40868dc994dfe8537d7115, reversing
changes made to ab3453e7b12daef47b9e91da2a2a3d48615dc6fc.
Link: https://lore.kernel.org/u-boot/[email protected]/
Signed-off-by: Tom Rini <[email protected]>
|
|
Currently, fastboot protocol in U-Boot has no opportunity
to execute vendor custom code with verifed boot. This patch
introduce new fastboot subcommand fastboot oem board:<cmd>,
which allow to run custom oem_board function.
Default implementation is __weak. Vendor must redefine it in
board/ folder with his own logic.
For example, some vendors have their custom nand/emmc partition
flashing or erasing. Here some typical command for such use cases:
- flashing:
$ fastboot stage bootloader.img
$ fastboot oem board:write_bootloader
- erasing:
$ fastboot oem board:erase_env
Signed-off-by: Alexey Romanov <[email protected]>
Reviewed-by: Mattijs Korpershoek <[email protected]>
Reviewed-by: Quentin Schulz <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mattijs Korpershoek <[email protected]>
|
|
Simon Glass <[email protected]> says:
This series is the culmanation of the current line of refactoring
series. It adjusts pxe to call the booting functionality directly
rather than going through the command-line interface.
With this is is possible to boot using the extlinux bootmeth without
the command line enabled.
It also updates fastboot to do a similar thing.
|
|
The fastboot 'boot' command only supports running a U-Boot command if
CONFIG_CMDLINE is enabled. Mention this in the documentation.
Signed-off-by: Simon Glass <[email protected]>
Suggested-by: Tom Rini <[email protected]>
Reviewed-by: Mattijs Korpershoek <[email protected]>
Reviewed-by: Sam Protsenko <[email protected]>
|
|
"oem console" serves to read console record buffer.
Signed-off-by: Ion Agorria <[email protected]>
Signed-off-by: Svyatoslav Ryhel <[email protected]>
Reviewed-by: Mattijs Korpershoek <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mattijs Korpershoek <[email protected]>
|
|
This adds the UUU UCmd functionality as an OEM command. While the
fastboot tool allows sending arbitrary commands as long as they are
prefixed with "oem". This allows running generic U-Boot commands over
fastboot without UUU, which is especially useful when not using USB.
This is really the route we should have gone in the first place when
adding these commands.
While we're here, clean up the UUU Kconfig a bit.
Signed-off-by: Sean Anderson <[email protected]>
Reviewed-by: Heiko Schocher <[email protected]>
|
|
add support for the UUU commands ACmd and UCmd.
Enable them through the Kconfig option
CONFIG_FASTBOOT_UUU_SUPPORT
base was commit in NXP kernel
9b149c2a2882: ("MLK-18591-3 android: Add FSL android fastboot support")
and ported it to current mainline. Tested this patch
on imx6ul based board.
Signed-off-by: Heiko Schocher <[email protected]>
Acked-by: Patrick Delaunay <[email protected]>
|
|
This documents the way U-Boot understands partitions specifications.
This also updates the fastboot documentation for the changes in the
previous commit.
Signed-off-by: Sean Anderson <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Add command oem bootbus which executes the command
``mmc bootbus <id> <arg>`` on the current fastboot mmc device
(<i> = CONFIG_FASTBOOT_FLASH_MMC_DEV) to set the eMMC boot
configuration on first update, with
<arg> = boot_bus_width reset_boot_bus_width boot_mode
$> fastboot oem bootbus:<boot_bus_width> <reset_boot_bus_width> <boot_mode>
Signed-off-by: Patrick Delaunay <[email protected]>
|
|
Add fastboot command oem partconf which executes the command
``mmc partconf <id> <arg> 0`` on the current <id> mmc device
to configure the eMMC boot partition with
<arg>: boot_ack boot_partition, so the command is:
$> fastboot oem partconf:<boot_ack> <boot_partition>
The partition_access argument is forced to 0 (userdata)
Signed-off-by: Patrick Delaunay <[email protected]>
[lukma - Kconfig adjustments after merging this patch]
|
|
Add support for defining raw fastboot partitions in eMMC by specifying
the offset and size in an environment variable. Optionally, the eMMC
hardware partition number may also be specified.
This makes it possible to e.g. update only part of the eMMC boot
partition, instead of having to write the entire partition.
Signed-off-by: Filip Brozovic <[email protected]>
|
|
Convert Android documentation from regular txt format to Sphinx (RST).
Also add Android index.rst file and reference it in root index.rst, so
that Android documentation is visible.
Test:
$ make htmldocs
$ xdg-open doc/output/index.html
Signed-off-by: Sam Protsenko <[email protected]>
Signed-off-by: Lokesh Vutla <[email protected]>
|
