| Age | Commit message (Collapse) | Author |
|---|
|
U-Boot produces flash.bin as the final boot image when building for
the i.MX95 EVK, but the documentation refers to imx-boot-imx95.bin.
Update the instructions to use flash.bin when copying the image to
the SD card.
Signed-off-by: Fabio Estevam <[email protected]>
|
|
The imx-oei and imx-sm build systems defaults to:
TC_VERSION ?= 14.2.rel1
but the documentation still instructs users to download the 13.3 toolchain.
This causes the build to fail because the expected directory name does
not exist.
Update the documentation to reference the 14.2 toolchain to match the build
system default.
Signed-off-by: Fabio Estevam <[email protected]>
Acked-by: Peng Fan <[email protected]>
|
|
Add support for i.MX952 15x15 lpddr4x board support.
Signed-off-by: Peng Fan <[email protected]>
Signed-off-by: Ye Li <[email protected]>
Signed-off-by: Alice Guo <[email protected]>
|
|
Select remoteproc related configs for i.MX95 EVK to support manage CM7
using 'rproc' cmd.
Update doc to show details on starting CM7 using rproc cmd.
Signed-off-by: Peng Fan <[email protected]>
|
|
Add i.MX91 11x11 FRDM Board support.
- Four ddr scripts included w/o inline ecc feature. Support
both 1gb and 2gb DDR
- SDHC/EQOS/I2C/UART supported
- PCA9451 supported, default nominal drive mode
- Documentation added.
Signed-off-by: Joseph Guo <[email protected]>
|
|
Add boot support and peripherals like eMMC/SD, UART, I2C, GPIO, ENETC0/1
and PCIE0/1 for iMX95 15x15 LPDDR4X EVK.
Updated doc for build instructions.
Signed-off-by: Ye Li <[email protected]>
|
|
Add guide on how to use the Remote Processors on i.MX8M and i.MX93.
Update MAINTAINERS to include doc/board/nxp.
Signed-off-by: Peng Fan <[email protected]>
|
|
Add board-level code and defconfig for the i.MX943 EVK board, supporting
multiple SOM variants: 19x19 LPDDR5, 19x19 LPDDR4 and 15x15 LPDDR4.
Signed-off-by: Ye Li <[email protected]>
Signed-off-by: Alice Guo <[email protected]>
Acked-by: Peng Fan <[email protected]>
Reviewed-by: Jacky Bai <[email protected]>
|
|
Prepare v2025.10-rc5
|
|
Allow to flash a board using NXP UUU utility:
- Enable fastboot support on USB.
- Add fastboot partition aliases with names used by UUU. Also add extra
environment variables used by UUU.
- Set 'dofastboot' environment variable based on boot device
configuration, allowing to automatically enter fastboot when booting
from USB.
Signed-off-by: Mathieu Dubois-Briand <[email protected]>
|
|
This patch is used to restore support for i.MX95 A0 silicon. To avoid
duplicating defconfig, imx95.config is added and can be shared between
imx95_a0_19x19_evk_defconfig and imx95_19x19_evk_defconfig.
container.cfg and imximage.cfg are used to created .cfgout files that
are be passed to mkimage with -n to build flash.bin. Now they have been
deleted and replaced by adding their content to properties of node which
type is nxp-imx9image under binman node.
Fixes: 9936724aa9b ("imx95_evk: Add i.MX95 B0 support")
Signed-off-by: Alice Guo <[email protected]>
Tested-By: Tim Harvey <[email protected]> # imx95-19x19-evk (rA0)
|
|
Add the initial board support for the NXP i.MX93 FRDM board:
https://www.nxp.com/design/design-center/development-boards-and-designs/frdm-i-mx-93-development-board:FRDM-IMX93
Based on the NXP U-Boot code.
There were attempts to upstream the board devicetree, but it has not been
accepted upstream yet:
https://lore.kernel.org/linux-arm-kernel/[email protected]/
Once it reaches upstream, we can switch to OF_UPSTREAM.
Signed-off-by: Fabio Estevam <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
|
|
i.MX95 B0 uses image container format v2 and needs DUMMY_DDR so that
update imximage.cfg and container.cfg for it.
Signed-off-by: Alice Guo <[email protected]>
|
|
This patch adds i.MX95 19x19 EVK board basic support.
Messaging unit for EdgeLock Secure Enclave, messaging unit for System
Manager, uSDHC for SD Card, gpio, lpuart are supported now.
Signed-off-by: Ye Li <[email protected]>
Signed-off-by: Alice Guo <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
|
|
Add i.MX91 11x11 EVK Board support.
- Four ddr scripts included w/o inline ecc feature.
- SDHC/NETWORK/I2C/UART supported
- PCA9451 supported, default nominal drive mode
- Documentation added.
Signed-off-by: Ye Li <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
|
|
Add i.MX93 9x9 Quick Start Board support.
- Two ddr scripts included w/o inline ecc feature.
- SDHC/NETWORK/I2C/UART supported
- PCA9450 supported, default over drive mode
- Documentation added.
Signed-off-by: Peng Fan <[email protected]>
|
|
Enable binman support and add documentation for the
imx8ul-evk board.
Signed-off-by: Gary Bisson <[email protected]>
|
|
Use the latest, mx93a1-ahab-container.img that is compatible with the
i.MX93 A1 revision.
Using mx93a1-ahab-container.img on an A0 chip and conversely causes a boot
failure without any traces on the UART.
Signed-off-by: Mathieu Othacehe <[email protected]>
|
|
Add documentation for SPI boot.
Signed-off-by: Jesse Taube <[email protected]>
|
|
Add documentation for imxrt1170-evk.
Signed-off-by: Jesse Taube <[email protected]>
Reviewed-by: Giulio Benetti <[email protected]>
Add index page entry, adjust formatting.
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
Signed-off-by: Mathieu Othacehe <[email protected]>
|
|
Title underlines should match the length of the title. Unfortunately
docutils only catches underlines that are too short.
Add some missing empty lines after titles.
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
To make it consistent with the instructions from other NXP imx8m boards,
such as imx8mm-evk and imx8mn-evk, use U-Boot in-tree build in the
examples.
Signed-off-by: Fabio Estevam <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
|
|
Originally, exporting the ATF_LOAD_ADDR was required, but since binman has
been used to generate the flash.bin, it is no longer needed to do
such manual export.
The ATF address is now passed via binman in imx8mp-u-boot.dtsi:
atf {
description = "ARM Trusted Firmware";
type = "firmware";
arch = "arm64";
compression = "none";
load = <0x970000>;
entry = <0x970000>;
atf_blob: atf-blob {
filename = "bl31.bin";
type = "atf-bl31";
};
};
Remove the unneeded export ATF_LOAD_ADDR line.
Signed-off-by: Fabio Estevam <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
|
|
Use proper project name in comments, Kconfig, readmes.
Reviewed-by: Neil Armstrong <[email protected]>
Acked-by: Ilias Apalodimas <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
Reviewed-by: Qu Wenruo <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/0dbdf0432405c1c38ffca55703b6737a48219e79.1684307818.git.michal.simek@amd.com
|
|
As explained in the text at the bottom of the page
https://source.codeaurora.org/external/imx/imx-atf:
"QUIC repositories on this site will not receive any updates after
March 31, 2022, and will be deleted on March 31, 2023."
Point to the NXP ATF github repo instead.
Signed-off-by: Fabio Estevam <[email protected]>
Reviewed-by: Oliver Graute <[email protected]>
Reviewed-by: Marcel Ziswiler <[email protected]>
Reviewed-by: Frieder Schrempf <[email protected]>
|
|
Switch to use binman pack images
Signed-off-by: Oliver Graute <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
|
|
The current name is inconsistent with SPL which uses CONFIG_SPL_TEXT_BASE
and this makes it imposible to use CONFIG_VAL().
Rename it to resolve this problem.
Signed-off-by: Simon Glass <[email protected]>
|
|
Add instructions to build and boot from QSPI Flash
Signed-off-by: Mamta Shukla <[email protected]>
Signed-off-by: Thomas Haemmerle <[email protected]>
Tested-by: Adam Ford <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
The imx8mn_evk target have been converted to use binman.
With the binman approach the ATF load address is described via
devicetree, so remove the now unneeded instruction of exporting
ATF_LOAD_ADDR.
Signed-off-by: Fabio Estevam <[email protected]>
|
|
This adds support for booting entirely from JTAG while using a
hard-coded RCW. With these steps, it is not necessary to program a
"good" RCW using CodeWarrior. The method here can be performed with any
JTAG adapter supported by OpenOCD, including the on-board CMSIS-DAP
(albeit very slowly).
These steps require LS1046A support in OpenOCD, which was added in [1].
[1] https://sourceforge.net/p/openocd/code/ci/5b70c1f679755677c925b4e6dd2c3d8be4715717/
Signed-off-by: Sean Anderson <[email protected]>
[trini: Add reference to doc/board/nxp/ls1046ardb.rst]
|
|
This adds some instructions for enabling the debug uart, including the
correct address and clock rate.
Signed-off-by: Sean Anderson <[email protected]>
|
|
This adds some additional info about booting from different sources,
including the correct switch positions.
Signed-off-by: Sean Anderson <[email protected]>
|
|
This converts the readme for this board to rST. I have tried not to
change any semantics from the original (though I did convert MB to M).
Signed-off-by: Sean Anderson <[email protected]>
|
|
As suggested in commit 028abfd9b157 ("imx8mm-evk: Generate a single
bootable flash.bin again") for imx8mm_evk, it is possible to produce
single bootable image via binman. This restores the original behavior in
distros, where only one boot container is used to create target image.
Perform similar adaptions in order to provide single bootable image for
imx8mn-ddr4-evk derivate.
Update documentation to drop additional step of copying u-boot.itb
Fixes: 353dfe4b4359 ("imx8mn-ddr4-evk: switch to use binman")
Signed-off-by: Andrey Zhizhikin <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
imx8mm-u-boot.dtsi passes the ATF load address via the
'entry' and 'load' properties.
Remove the step that performs the ATF_LOAD_ADDR export, which is
now unneeded.
Signed-off-by: Fabio Estevam <[email protected]>
Reviewed-by: Patrick Wildt <[email protected]>
|
|
All i.MX8MQ boards have been converted to binman, which makes it
necessary to flash both flash.bin and u-boot.itb to get a bootable
system. Prior to the conversion, only flash.bin was needed.
Such new requirement breaks existing distro mechanisms to generate the
final binary because the extra u-boot.itb is now required.
Generate a final flash.bin that can be used again as a single bootable
binary to keep the original behavior.
After this change the SPL binary is called spl.bin, which is a more
descriptive name for its purpose, and can still be used standalone (for
example, for secure boot purposes).
Also update imx8mq_evk.rst to remove the u-boot.itb copy step.
This is a cherry-pick of 028abfd9b157 ("imx8mm-evk: Generate a single
bootable flash.bin again") adjusted to apply to i.MX8MQ.
Signed-off-by: Patrick Wildt <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
Update doc after using binman to pack images
Signed-off-by: Peng Fan <[email protected]>
|
|
On iMX8MM with Fast Boot fuse blown, the SIT and A-copy image are
placed at different offset than on iMX8MM with Fast Boot fuse NOT
blown. List both options and both offsets to avoid confusion.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Marcel Ziswiler <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Ye Li <[email protected]>
Cc: uboot-imx <[email protected]>
Reviewed-by: Marcel Ziswiler <[email protected]>
|
|
The PERSIST_SECONDARY_BOOT is in GPR10 address 0x30390098, adjust the
text which currently says it is in GPR0 while using the correct address
of GPR10.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Marcel Ziswiler <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Ye Li <[email protected]>
Cc: uboot-imx <[email protected]>
Reviewed-by: Marcel Ziswiler <[email protected]>
|
|
After the conversion to binman in commit 8996e6b7c6a1 ("imx8mm_evk: switch
to use binman to pack images"), it is necessary to flash both flash.bin and
u-boot.itb to get a bootable system. Prior to this commit, only flash.bin
was needed.
Such new requirement breaks existing distro mechanisms to generate the
final binary because the extra u-boot.itb is now required.
Generate a final flash.bin that can be used again as a single
bootable binary to keep the original behavior.
After this change the SPL binary is called spl.bin, which is a more
descriptive name for its purpose, and can still be used standalone
(for example, for secure boot purposes).
Also update imx8mm_evk.rst to remove the u-boot.itb copy step.
Signed-off-by: Fabio Estevam <[email protected]>
Reviewed-by: Frieder Schrempf <[email protected]>
Reviewed-by: Heiko Schocher <[email protected]>
Reviewed-by: Marcel Ziswiler <[email protected]>
Reviewed-by: Heiko Thiery <[email protected]>
|
|
binman conversion made flashing flash.bin
and u-boot.itb necessary. Update binman config
to create a single flash.bin image again.
This updates imx8mp_evk and phyCORE-i.MX8MP as they share the
same binman config.
Updated also imx8mp_evk documentation.
Tested on phyCORE-i.MX8MP.
Signed-off-by: Teresa Remmet <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
Reviewed-by: Heiko Schocher <[email protected]>
|
|
Freescale Semiconductor, Inc. was merged into NXP Semiconductors in 2015.
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
