| Age | Commit message (Collapse) | Author |
|---|
|
The phyCORE-i.MX 93 is available in various variants (e.g. different ram
sizes, eMMC HS400 yes/no). Enable hardware introspection for the
imx93-phyboard-segin_defconfig, so that during startup the SOM module
variant can be detected, and the hardware can be configured accordingly.
The resulting SPL and u-boot binary shall able to boot each
phyCORE-i.MX 93 module variant on each carrier board. Finally rename
imx93-phyboard-segin_defconfig to imx93-phycore_defconfig, to highlight
its SOM scope.
Signed-off-by: Christoph Stoidner <[email protected]>
Reviewed-by: Wadim Egorov <[email protected]>
Reviewed-by: Yannic Moog <[email protected]>
|
|
Add support for packaging the TIFS Stub as it's required for basic Low
Power Modes like Deep Sleep.
The reason it is packaged using binman and not inherently as part of the
DM firmware is because for HS devices, customer owns the customer key
and only customer has access to it.
DM is release by TI, Since TI doesn't have access to the customer key it
cannot have a component that is signed by customer key.
Hence, it's left as part of binman to be signed and packaged.
While at it, also make sure it's documented in phycore-am62x
Reviewed-by: Nishanth Menon <[email protected]>
Reviewed-by: Wadim Egorov <[email protected]>
Signed-off-by: Dhruva Gole <[email protected]>
|
|
Use the new boot_firmwares labels that help make documentation more
specific as to which firmwares are used in which devices
Signed-off-by: Dhruva Gole <[email protected]>
|
|
Describe how to boot via UART.
Signed-off-by: Wadim Egorov <[email protected]>
|
|
Prepare v2024.07-rc5
|
|
Update Flash to SPI NOR chapter for use with mtd commands.
This is more convenient as we do not have to remember any
offsets in the SPI.
Signed-off-by: Wadim Egorov <[email protected]>
Reviewed-by: Daniel Schultz <[email protected]>
|
|
Provide boot switch config for USB DFU boot.
Signed-off-by: Wadim Egorov <[email protected]>
Reviewed-by: Daniel Schultz <[email protected]>
|
|
The Carrier-Board for the pyhCORE-AM64x is called phyBOARD-Electra.
Signed-off-by: Daniel Schultz <[email protected]>
|
|
We moved our documentation to another hoster and therefore the URL
changed. Point to the latest documentation instead of release versions
to not link out-dated documentation.
Signed-off-by: Daniel Schultz <[email protected]>
|
|
We moved our documentation to another hoster and therefore the URL
changed. Point to the latest documentation instead of release versions
to not link out-dated documentation.
Signed-off-by: Daniel Schultz <[email protected]>
Reviewed-by: Wadim Egorov <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-socfpga into next
- A new driver in the misc to register setting from device tree. This
also provides user a clean interface and all register settings are
centralized in one place, device tree.
- Enable Agilex5 platform for Intel product. Changes, modification and
new files are created for board, dts, configs and makefile to create
the base for Agilex5.
Build-tested on SoC64 boards, boot tested on some of them.
|
|
Use proper binary artifact names for HSFS devices.
Do not use the *_unsigned binaries.
Signed-off-by: Wadim Egorov <[email protected]>
Reviewed-by: Dhruva Gole <[email protected]>
|
|
Prepare v2024.04-rc4
|
|
Add documentation for PHYTEC phyCORE-AM64x SoM.
Signed-off-by: Wadim Egorov <[email protected]>
Reviewed-by: Dhruva Gole <[email protected]>
|
|
Use the latest, mx93a1-ahab-container.img that is compatible with the
i.MX93 A1 revision.
Using mx93a1-ahab-container.img on an A0 chip and conversely causes a boot
failure without any traces on the UART.
Signed-off-by: Mathieu Othacehe <[email protected]>
|
|
Add initial support for the PHYTEC phyBOARD-Segin-i.MX93 board based on
the PHYTEC phyCORE-i.MX93 SoM.
Supported features:
- 1GB LPDDR4 RAM
- eMMC
- external SD
- FEC Ethernet
- debug UART
- watchdog
Signed-off-by: Mathieu Othacehe <[email protected]>
Tested-by: Primoz Fiser <[email protected]>
Reviewed-by: Yannic Moog <[email protected]>
|
|
Add documentation for PHYTEC phyCORE-AM62x SoM.
Signed-off-by: Wadim Egorov <[email protected]>
Reviewed-by: Dhruva Gole <[email protected]>
|
|
Add brief documentation on how to build a bootable U-Boot image for the
phyGATE-Tauri-L.
Signed-off-by: Yannic Moog <[email protected]>
Reviewed-by: Teresa Remmet <[email protected]>
|
|
Add documentation on how to build a bootable U-Boot image for the PHYTEC
phyCORE-i.MX 8M Plus.
Signed-off-by: Yannic Moog <[email protected]>
|
|
Add documentation on how to build a bootable U-Boot image for the PHYTEC
phyCORE-i.MX 8M Mini.
Signed-off-by: Yannic Moog <[email protected]>
|
