| Age | Commit message (Collapse) | Author |
|---|
|
|
|
As the PHYTEC phyCORE-i.MX91 [1] is just another variant of the existing
PHYTEC phyCORE-i.MX93 SoM but with i.MX91 SoC populated instead, add it
to the existing board-code "phycore_imx93", and rename that board to
"phycore_imx91_93" to reflect the dual SoCs support. While at it, also
rename and change common files accordingly. This way i.MX91 and i.MX93
SoC variants of the phyCORE SoM share most of the code and documentation
without duplication, while maintaining own device-tree and defconfigs
for each CPU variant.
Supported features:
- 1GB LPDDR4 RAM
- Debug UART
- EEPROM
- eMMC
- Ethernet
- SD-card
- USB
Product page SoM:
[1] https://www.phytec.eu/en/produkte/system-on-modules/phycore-imx-91-93/
Signed-off-by: Primoz Fiser <[email protected]>
|
|
CFG_WITH_SOFTWARE_PRNG=y was added as an OPTEE argument to workaround
some bugs related to TRNG which have been fixed now[1]. Therefore this
patch drops the redundant argument from the documentation.
[1]: https://github.com/OP-TEE/optee_os/commit/e313f4765fd0478bb66985827441411793433773
Signed-off-by: Anshul Dalal <[email protected]>
Acked-by: Francesco Dolcini <[email protected]> # Toradex Verdin AM62
|
|
Add documentation for the PHYTEC phyCORE-AM68x/TDA4x (J721S2 family) SoM.
Signed-off-by: Dominik Haller <[email protected]>
Reviewed-by: Wadim Egorov <[email protected]>
|
|
Use single make command for compiling blobs and U-Boot.
Update the imx firmware version.
Signed-off-by: Yannic Moog <[email protected]>
|
|
OP-TEE configs are enabled by default, change the doc to no longer
declare OP-TEE as optional. Also remove CFG_TEE_BENCHMARK as it is no
longer present in optee_os.
Further, phycore-imx8mm and imx8mm-phygate-tauri-l use different build
instructions, so dissolve the common file for building OP-TEE.
Reviewed-by: Teresa Remmet <[email protected]>
Signed-off-by: Yannic Moog <[email protected]>
|
|
Add new imx8mp-libra-fpsc board.
Bootph tags as well as USB device tree nodes are in u-boot.dtsi for now
and will be removed when upstreamed.
The Libra i.MX 8M Plus FPSC is a single board computer. It uses an i.MX
8M Plus FPSC [1] System on Module which utilizes the FPSC standard [2].
[1] https://www.phytec.eu/en/produkte/system-on-modules/phycore-imx-8m-plus-fpsc
[2] https://www.phytec.eu/en/produkte/system-on-modules/fpsc
Signed-off-by: Benjamin Hahn <[email protected]>
Reviewed-by: Teresa Remmet <[email protected]>
Tested-by: Teresa Remmet <[email protected]>
Signed-off-by: Yannic Moog <[email protected]>
|
|
Provide a common part for our K3 based boards including general details
about environment handling and EFI capsule updates.
Signed-off-by: Wadim Egorov <[email protected]>
|
|
Add instructions on how to build and package OP-TEE for the
phycore-imx8mm based boards. The build instructions are identical for
phyGATE-Tauri-L and phyBOARD-Polis.
Also fix missig '-' for TF-A build instructions.
Signed-off-by: Yannic Moog <[email protected]>
|
|
Add documentation for the phyBOARD-Pollux i.MX 8M Plus on OP-TEE
integration.
Also add missing '-' to TF-A build instruction while at it.
Signed-off-by: Yannic Moog <[email protected]>
|
|
Garrett Giordano <[email protected]> says:
This patch set adds the phyCORE AM62Ax board support and documenation to
u-boot.
The phyCORE-AM62Ax is a SoM (System on Module) featuring TI's AM62Ax SoC. It can
be used in combination with different carrier boards. This module can come
with different sizes and models for DDR, eMMC, SPI NOR Flash and various SoCs
from the AM62x family.
A development Kit, called phyBOARD-Lyra is used as a carrier board reference
design around the AM62x SoM.
This series depends on the following two patches:
- [PATCH v2] arm: mach-k3: am62a7: Provide a way to obtain boot device for non SPL
https://lists.denx.de/pipermail/u-boot/2024-October/570156.html
- [PATCH] board: phytec: common: Introduce CONFIG_PHYTEC_K3_DDR_PATCH
https://lists.denx.de/pipermail/u-boot/2024-November/571543.html
Link: https://lore.kernel.org/r/[email protected]
[trini: Fix warning in board/phytec/common/k3/board.c when
CONFIG_EFI_HAVE_CAPSULE_SUPPORT is not enabled]
Signed-off-by: Tom Rini <[email protected]>
|
|
Add documentation for PHYTEC phyCORE-AM62ax SoM.
Signed-off-by: Garrett Giordano <[email protected]>
Reviewed-by: Wadim Egorov <[email protected]>
Reviewed-by: Dhruva Gole <[email protected]>
|
|
The phyCORE-i.MX 93 is available in various variants (e.g. different ram
sizes, eMMC HS400 yes/no). Enable hardware introspection for the
imx93-phyboard-segin_defconfig, so that during startup the SOM module
variant can be detected, and the hardware can be configured accordingly.
The resulting SPL and u-boot binary shall able to boot each
phyCORE-i.MX 93 module variant on each carrier board. Finally rename
imx93-phyboard-segin_defconfig to imx93-phycore_defconfig, to highlight
its SOM scope.
Signed-off-by: Christoph Stoidner <[email protected]>
Reviewed-by: Wadim Egorov <[email protected]>
Reviewed-by: Yannic Moog <[email protected]>
|
|
Add support for packaging the TIFS Stub as it's required for basic Low
Power Modes like Deep Sleep.
The reason it is packaged using binman and not inherently as part of the
DM firmware is because for HS devices, customer owns the customer key
and only customer has access to it.
DM is release by TI, Since TI doesn't have access to the customer key it
cannot have a component that is signed by customer key.
Hence, it's left as part of binman to be signed and packaged.
While at it, also make sure it's documented in phycore-am62x
Reviewed-by: Nishanth Menon <[email protected]>
Reviewed-by: Wadim Egorov <[email protected]>
Signed-off-by: Dhruva Gole <[email protected]>
|
|
Use the new boot_firmwares labels that help make documentation more
specific as to which firmwares are used in which devices
Signed-off-by: Dhruva Gole <[email protected]>
|
|
Describe how to boot via UART.
Signed-off-by: Wadim Egorov <[email protected]>
|
|
Prepare v2024.07-rc5
|
|
Update Flash to SPI NOR chapter for use with mtd commands.
This is more convenient as we do not have to remember any
offsets in the SPI.
Signed-off-by: Wadim Egorov <[email protected]>
Reviewed-by: Daniel Schultz <[email protected]>
|
|
Provide boot switch config for USB DFU boot.
Signed-off-by: Wadim Egorov <[email protected]>
Reviewed-by: Daniel Schultz <[email protected]>
|
|
The Carrier-Board for the pyhCORE-AM64x is called phyBOARD-Electra.
Signed-off-by: Daniel Schultz <[email protected]>
|
|
We moved our documentation to another hoster and therefore the URL
changed. Point to the latest documentation instead of release versions
to not link out-dated documentation.
Signed-off-by: Daniel Schultz <[email protected]>
|
|
We moved our documentation to another hoster and therefore the URL
changed. Point to the latest documentation instead of release versions
to not link out-dated documentation.
Signed-off-by: Daniel Schultz <[email protected]>
Reviewed-by: Wadim Egorov <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-socfpga into next
- A new driver in the misc to register setting from device tree. This
also provides user a clean interface and all register settings are
centralized in one place, device tree.
- Enable Agilex5 platform for Intel product. Changes, modification and
new files are created for board, dts, configs and makefile to create
the base for Agilex5.
Build-tested on SoC64 boards, boot tested on some of them.
|
|
Use proper binary artifact names for HSFS devices.
Do not use the *_unsigned binaries.
Signed-off-by: Wadim Egorov <[email protected]>
Reviewed-by: Dhruva Gole <[email protected]>
|
|
Prepare v2024.04-rc4
|
|
Add documentation for PHYTEC phyCORE-AM64x SoM.
Signed-off-by: Wadim Egorov <[email protected]>
Reviewed-by: Dhruva Gole <[email protected]>
|
|
Use the latest, mx93a1-ahab-container.img that is compatible with the
i.MX93 A1 revision.
Using mx93a1-ahab-container.img on an A0 chip and conversely causes a boot
failure without any traces on the UART.
Signed-off-by: Mathieu Othacehe <[email protected]>
|
|
Add initial support for the PHYTEC phyBOARD-Segin-i.MX93 board based on
the PHYTEC phyCORE-i.MX93 SoM.
Supported features:
- 1GB LPDDR4 RAM
- eMMC
- external SD
- FEC Ethernet
- debug UART
- watchdog
Signed-off-by: Mathieu Othacehe <[email protected]>
Tested-by: Primoz Fiser <[email protected]>
Reviewed-by: Yannic Moog <[email protected]>
|
|
Add documentation for PHYTEC phyCORE-AM62x SoM.
Signed-off-by: Wadim Egorov <[email protected]>
Reviewed-by: Dhruva Gole <[email protected]>
|
|
Add brief documentation on how to build a bootable U-Boot image for the
phyGATE-Tauri-L.
Signed-off-by: Yannic Moog <[email protected]>
Reviewed-by: Teresa Remmet <[email protected]>
|
|
Add documentation on how to build a bootable U-Boot image for the PHYTEC
phyCORE-i.MX 8M Plus.
Signed-off-by: Yannic Moog <[email protected]>
|
|
Add documentation on how to build a bootable U-Boot image for the PHYTEC
phyCORE-i.MX 8M Mini.
Signed-off-by: Yannic Moog <[email protected]>
|
