| Age | Commit message (Collapse) | Author |
|---|
|
Michal Simek <[email protected]> says:
I looked as cleaning up some dependencies and I found that qconfig is
reporting some issues. This series is fixing some of them. But there are
still some other pending. That's why please go and fix them if they are
related to your board.
UTF-8: I am using uni2ascii -B < file to do conversion. When you run it in
a loop you will find some other issue with copyright chars or some issues
in files taken from the Linux kernel like DTs. They should be likely fixed
in the kernel first.
Based on discussion I am ignoring names too.
|
|
Convert UTF-8 chars to ASCII in cases where make sense. No Copyright or
names are converted.
Signed-off-by: Michal Simek <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Acked-by: Marek Behún <[email protected]>
|
|
Some of Kconfigs are using utf-8 encoding because of used chars. Convert
all of them to ascii enconging. Based on discussion ASCII should be used in
general with the exception of names.
Signed-off-by: Michal Simek <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
FMC2 IP supports up to 4 chip select. On MP1 SoC, only 2 of them are
available when on MP25 SoC, the 4 chip select are available.
Let's use a platform data structure for parameters that will differ.
Signed-off-by: Christophe Kerello <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-nand-flash
The first patch is by Weizhao Ouyang and avoids sf probe crashes.
The second patch is by Arseniy Krasnov and adds basic support for Amlogic
Meson NAND controller on AXG.
The following four patches are by Alexander Dahl and apply some fixes to
drivers/mtd/nand/raw/ and port some changes applied in Linux.
The following patch is by Bruce Suen and adds support for XTX SPINAND.
Finally, the last patch is again by Arseniy Krasnov and adds access to
OTP region, supporting info, dump, write and lock operations.
|
|
Add support for XTX XT26G0xA and XT26xxxD. The driver is ported from
linux-6.7.1. This driver is tested on Banana BPI-R3 with XT26G01A and
XT26G12D.
Link: https://lore.kernel.org/all/[email protected]
Signed-off-by: Bruce Suen <[email protected]>
Reviewed-by: Frieder Schrempf <[email protected]>
Signed-off-by: Dario Binacchi <[email protected]>
|
|
Introduced with commit 6a8dfd57220d ("nand: atmel: Add DM based NAND
driver") when driver was initially ported from Linux. The context
around this and especially the code itself suggests 'read' is meant
instead of write.
The fix is the same as accepted in Linux already with mainline Linux
kernel commit 1c60e027ffde ("mtd: nand: raw: atmel: Fix comment in
timings preparation").
Link: https://lore.kernel.org/all/[email protected]
Link: https://lore.kernel.org/linux-mtd/[email protected]/T/#t
Signed-off-by: Alexander Dahl <[email protected]>
Reviewed-by: Michael Trimarchi <[email protected]>
Signed-off-by: Dario Binacchi <[email protected]>
|
|
One tab in general. One tab plus two spaces for help text.
Link: https://lore.kernel.org/all/[email protected]
Signed-off-by: Alexander Dahl <[email protected]>
Reviewed-by: Michael Trimarchi <[email protected]>
Signed-off-by: Dario Binacchi <[email protected]>
|
|
Introduced in upstream Linux with commit 7a08dbaedd365 for release v5.0.
When the new atmel nand driver was backported to U-Boot with commit
6a8dfd57220d ("nand: atmel: Add DM based NAND driver") that definition
was added to the driver instead of the header file. Move it over to the
other definitions with the same help text it has in Linux.
Code actually using this has not been ported over to raw nand base yet.
Link: https://lore.kernel.org/all/[email protected]
Signed-off-by: Alexander Dahl <[email protected]>
Reviewed-by: Michael Trimarchi <[email protected]>
Signed-off-by: Dario Binacchi <[email protected]>
|
|
In every other place in this file the macro is used, make it consistent.
Link: https://lore.kernel.org/all/[email protected]
Fixes: 9d1806fadc24 ("mtd: nand: Get rid of mtd variable in function calls")
Signed-off-by: Alexander Dahl <[email protected]>
Reviewed-by: Michael Trimarchi <[email protected]>
Signed-off-by: Dario Binacchi <[email protected]>
|
|
Basic support for Amlogic Meson NAND controller on AXG. This version
works at only first EDO mode.
Based on Linux version 6.7.0-rc4.
Link: https://lore.kernel.org/all/[email protected]
Signed-off-by: Arseniy Krasnov <[email protected]>
Reviewed-by: Michael Trimarchi <[email protected]>
Signed-off-by: Dario Binacchi <[email protected]>
|
|
The below exception observed on QEMU, as it doesn't support
NAND controller.
"Synchronous Abort" handler, esr 0x96000005, far 0x17acfc878
elr: 000000000803ad40 lr : 000000000805f438 (reloc)
elr: 000000007fcb4d40 lr : 000000007fcd9438
x0 : 000000007bbfc880 x1 : 00000000ff100000
x2 : 000000007fcf059c x3 : 000000007bbfc870
x4 : 000000007fd9a388 x5 : 000000017acfc870
x6 : 0000000000000000 x7 : 000000007bbfd0e0
x8 : 0000000000003dd4 x9 : 000000007bbeec0c
x10: 0000000000000001 x11: 0000000000003f8c
x12: 000000007bbeecfc x13: 000000007bbeeeb0
x14: 000000007bbeeeb0 x15: 000000007bbee474
x16: 000000007fcef18c x17: 0000000000000000
x18: 000000007bbf9d70 x19: 000000007bbfc888
x20: 000000007bbfc870 x21: 000000007fd68ddb
x22: 00000000ffffffed x23: 000000007bbfc878
x24: 0000000000000000 x25: 0000000000000000
x26: 0000000000000000 x27: 0000000000000000
x28: 0000000000000000 x29: 000000007bbeed10
Code: 927ff8c1 924000c6 8b010065 f9400887 (f94004a2)
Resetting CPU ...
The crash is caused by the use after free.
Updating the correct return codes rather than hardcoding.
Fixes: 3dd0f8cccd6d ("mtd: nand: Remove hardcoded base address of nand")
Signed-off-by: Venkatesh Yadav Abbarapu <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michal Simek <[email protected]>
|
|
Currently only hw ecc is supported in U-Boot. If any other ecc mode is
given in DT, it simply through an error. So better print
what is being done.
Revert this patch once soft ecc support is fixed in future.
Signed-off-by: Ashok Reddy Soma <[email protected]>
Signed-off-by: Venkatesh Yadav Abbarapu <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michal Simek <[email protected]>
|
|
The datasheet can be found here:
https://www.esmt.com.tw/upload/pdf/ESMT/datasheets/EN25Q80B_Ver.E.pdf
Signed-off-by: Frieder Schrempf <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-at91
First set of u-boot-at91 features for the 2024.04 cycle:
This set includes some DT alignments and solves a compile issue for
custom nand defconfigs.
|
|
This function is a no-op. Remove it.
Signed-off-by: Sean Anderson <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Infineon(Cypress) S28HS02GT is 1.8V, 2Gb (256MB) NOR Flash memory with
Octal interface. It is a dual-die package parts and has same features
with existing S28 series.
Signed-off-by: Takahiro Kuwano <[email protected]>
Reviewed-by: Dhruva Gole <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
Enabling Octal DTR mode in multi-die package parts requires reister setup
for each die. That can be done by simple for-loop. write_enable() takes
effect to all die at once so we can call it before the loop. Besides we
can replace spi_mem_exec_op() calls with spansion_read/write_any_reg().
And finally, we must mask CFR2V[7:4] when changing dummy cycles, as
CFR2V[7] indicates current addressing mode and that should be 1 (4-byte
address mode) for multi-die package parts.
Signed-off-by: Takahiro Kuwano <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
and S28
s28hx_t_post_bfpt_fixup() fixes erase opcode, erase size, and page size.
s25_post_bfpt_fixup() is doing same thing including multi-die support.
We can consolidate s28hx_t_post_bfpt_fixup() and s25_post_bfpt_fixup()
into one named s25_s28_post_bfpt_fixup().
In s25_s28_post_bfpt_fixup(), set_4byte() is called to force the device to
be 4-byte addressing mode. In S28HS02GT datasheet, the B7 opcode is missing
but it works actually (confirmed).
Signed-off-by: Takahiro Kuwano <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
s28hx_t_setup() only checks sector layout setting. To support multi-die
package parts like S28HS02GT, it needs to check device size and assign
ready() hook for multi-die package parts. These are covered in s25_setup()
so we can consolidate s28hx_t_setup() and s25_setup() into one named
s25_s28_setup().
spi_nor_wait_till_ready() at the beginning of s28hx_t_setup() can be
removed since there is no op that makes device busy state before setup.
Signed-off-by: Takahiro Kuwano <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
s25_mdp_ready() handles status polling for multi-die package parts that
requires to read and check status register for each die. To support
S28HS02GT(dual-die package with Octal DTR support), rename function and
use nor->rdsr_dummy in octal DTR mode.
Signed-off-by: Takahiro Kuwano <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
Infineon(Cypress) S28Hx-T family does not support legacy CLSR(0x30) opcode.
Instead, it supports CLPEF(0x82) which has the same functionality as CLSR.
spansion_sr_ready() is for multi-die package parts including S28HS02GT, so
we need to use CLPEF instead of CLSR.
This change does not affect to S25x02GT which uses spansion_sr_ready() as
S25Hx-T family also supports CLPEF(0x82) as well as CLSR(0x30).
Signed-off-by: Takahiro Kuwano <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
In Infineon multi-die package parts, we need to use Read Any Register op
to read status register in 2nd or further die. Infineon S28HS02GT is
dual-die package and supports Octal DTR interface. To support this,
spansion_read_any_reg() needs to be reworked. Implementation is similar
to existing read_sr() that already supports Octal DTR mode.
Signed-off-by: Takahiro Kuwano <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
s25_erase_non_uniform() and s28hx_t_erase_uniform() support hybrid sector
layout (32 x 4KB sectors overlaid at bottom address) and doing same thing.
Consolidate them into single helper named s25_s28_erase_non_uniform().
Signed-off-by: Takahiro Kuwano <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
Some macro definitions used in Infineon(Cypress) S25 and S28 series are
redundant and some have inconsistent prefix. This patch removes
redundant ones and renames some to have same prefix as others.
Signed-off-by: Takahiro Kuwano <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
- XM25QH128C
- XM25QH256C
- XM25QU256C
- XM25QH512C
- XM25QU512C
Signed-off-by: Kankan Sun <[email protected]>
[jagan: update the commit message]
Signed-off-by: Jagan Teki <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
Added support for the ISSI OSPI flash part IS25LX512M.
Initial testing was performed on the Tenzing-se1 board using
SDR mode, covering basic erase, write, and readback operations.
Signed-off-by: Tejas Bhumkar <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
The help for CONFIG_MTD explains that it needs to be enabled for various
things like NAND, etc to be available. It however then doesn't enforce
this dependency and so if you have none of these systems present you
still need to disable a number of options. Fix this by making places
that select/imply one type of flash, but did not do the same, also do
this for "MTD". Make boards which hadn't been enabling MTD already but
need it now, do so. In a few places, disable CONFIG_CMD_MTDPARTS as it
wasn't previously enabled but was now being implied.
Signed-off-by: Tom Rini <[email protected]>
|
|
These removed definitions were specific to some sam9 SoCs, but not
generic over all at91 SoCs. The correct SoC specific definitions for
ATMEL_BASE_PMECC are spread over different header files in
arch/arm/mach-at91/include/mach directory.
Fixes a build error on a custon board based on SAMA5D2:
Building current source for 73 boards (16 threads, 1 job per thread)
arm: + vera2
+drivers/mtd/nand/raw/atmel/pmecc.c:819: warning: "ATMEL_BASE_PMECC" redefined
+ 819 | #define ATMEL_BASE_PMECC 0xffffe000
+ |
+In file included from include/configs/vera2.h:11,
+ from include/config.h:3,
+ from include/linux/mtd/rawnand.h:16,
+ from drivers/mtd/nand/raw/atmel/pmecc.c:44:
+include/asm/arch/sama5d2.h:171: note: this is the location of the previous definition
+ 171 | #define ATMEL_BASE_PMECC (ATMEL_BASE_HSMC + 0x70)
+drivers/mtd/nand/raw/atmel/pmecc.c:820: warning: "ATMEL_BASE_PMERRLOC" redefined
+ 820 | #define ATMEL_BASE_PMERRLOC 0xffffe600
+include/asm/arch/sama5d2.h:172: note: this is the location of the previous definition
+ 172 | #define ATMEL_BASE_PMERRLOC (ATMEL_BASE_HSMC + 0x500)
Fixes: a490e1b7c017 ("nand: atmel: Add pmecc driver")
Signed-off-by: Alexander Dahl <[email protected]>
|
|
Set NAND chip ofnode and device so OF based partition parsing
can work.
Signed-off-by: Roger Quadros <[email protected]>
Link: https://www.mail-archive.com/[email protected]/msg499178.html
Signed-off-by: Dario Binacchi <[email protected]>
|
|
For DM case we can get the NAND chip's IO address from DT
so we don't need to rely on CFG_SYS_NAND_BASE.
Signed-off-by: Roger Quadros <[email protected]>
Reviewed-by: Dario Binacchi <[email protected]>
Link: https://www.mail-archive.com/[email protected]/msg499177.html
Signed-off-by: Dario Binacchi <[email protected]>
|
|
The macro ELM_BASE is defined in mach/hardware.h and is
not visible at the omap_elm.h header file. Avoid using it
in omap_elm.h.
Reported-by: Hong Guan <[email protected]>
Fixes: 7363cf0581a3 ("mtd: rawnand: omap_elm: u-boot driver model support")
Signed-off-by: Roger Quadros <[email protected]>
Link: https://lore.kernel.org/all/[email protected]
Signed-off-by: Dario Binacchi <[email protected]>
|
|
AM335x uses a special driver "am335x_spl_bch.c" as SPL
NAND loader. This driver expects 1 sector at a time ECC
and doesn't work well with multi-sector ECC that was implemented in
commit 04fcd2587321 ("mtd: rawnand: omap_gpmc: Fix BCH6/16 HW based correction")
Additionally, the omap_elm driver does not support multi sector ECC and will
need more work and tests to get multi sector working correctly on all
platforms.
Switch back to 1 sector at a time read/ECC.
Fixes: 04fcd2587321 ("mtd: rawnand: omap_gpmc: Fix BCH6/16 HW based correction")
Signed-off-by: Roger Quadros <[email protected]>
Tested-by: Enrico Leto <[email protected]>
Tested-by: Heiko Schocher <[email protected]>
Link: https://lore.kernel.org/all/[email protected]/
Signed-off-by: Dario Binacchi <[email protected]>
|
|
If the "mtd" parameter is NULL, the search will definitely yield a
negative result. In that case, it's better to exit immediately.
Signed-off-by: Dario Binacchi <[email protected]>
Reviewed-by: Michael Trimarchi <[email protected]>
Link: https://lore.kernel.org/all/[email protected]
|
|
The patch checks that the "mtd" parameter is accessible before
proceeding.
Signed-off-by: Dario Binacchi <[email protected]>
Reviewed-by: Michael Trimarchi <[email protected]>
Link: https://lore.kernel.org/all/[email protected]
|
|
into next
- spi_nor_read_sfdp_dma_unsafe (Vaishnav)
- w25q01/02 (Jim)
|
|
Prepare v2024.01-rc5
|
|
Add support for XTX XT55Q02G(1.8V,2Gbit).
Signed-off-by: Bruce Suen <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
Adaptation of Linux commit d74c36480a67
This patch adds support for ESMT F50L1G41LB and F50D1G41LB.
It seems that ESMT likes to use random JEDEC ID from other vendors.
Their 1G chips uses 0xc8 from GigaDevice and 2G/4G chips uses 0x2c from
Micron. For this reason, the ESMT entry is named esmt_c8 with explicit
JEDEC ID in variable name.
Datasheets:
https://www.esmt.com.tw/upload/pdf/ESMT/datasheets/F50L1G41LB(2M).pdf
https://www.esmt.com.tw/upload/pdf/ESMT/datasheets/F50D1G41LB(2M).pdf
Signed-off-by: Igor Prusov <[email protected]>
Signed-off-by: Chuanhong Guo <[email protected]>
Signed-off-by: Martin Kurbanov <[email protected]>
Signed-off-by: Dmitry Rokosov <[email protected]>
Tested-by: Martin Kurbanov <[email protected]>
Reviewed-by: Frieder Schrempf <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
During SFDP header parse and BFPT parse, structures in stack are used
to perform spi_nor_read_sfdp() which expects a dma-safe buffer.
This commit introduces spi_nor_read_sfdp_dma_unsafe() to wrap
spi_nor_read_sfdp() using a kmalloc'ed bounce buffer which is
the same implementation in Linux (drivers/mtd/spi-nor/sfdp.c).
Signed-off-by: Vaishnav Achath <[email protected]>
Reviewed-by: Pratyush Yadav <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
add flash w25q01jv, w25q01jvfim and w25q02jv support
Signed-off-by: Jim Liu <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
Add Micron MT25QU128AB flash.
Signed-off-by: Godfrey Mwangi <[email protected]>
[jagan: fix the commit head]
Signed-off-by: Jagan Teki <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
MT25QU01 OPN with 4B OPCODE support is currently not supported in
source code and the driver reuses the definition for "n25q00a"
which has the same silicon ID but is a slower part.
Adding mt25u01g definition to the source code to support a faster
read response for MT25QU01 QSPI NOR Flash device.
Signed-off-by: Jit Loon Lim <[email protected]>
[jagan: fix the id position and commit head]
Signed-off-by: Jagan Teki <[email protected]>
|
|
Add Support for GigaDevice GD55LB02GEBIR SPI NOR flash as QSPI
configuration flash
Signed-off-by: Teik Heng Chong <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
Add support for the zBIT ZB25VQ128 (128M-bit) SPI NOR flash memory chip,
as used on the Xunlong Orange Pi Zero 3 board.
Signed-off-by: Andre Przywara <[email protected]>
Reviewed-by: Dragan Simic <[email protected]>
|
|
Add support for Silicon Kaiser sk25lp128 SPI NOR flash found in Pine64
PinePhone Pro and PineTab2.
Signed-off-by: Jonas Karlman <[email protected]>
|
|
To quote the author:
This series imports generic versions of ioread_rep/iowrite_rep and
reads/writes from Linux. Some cleanup is done to make sure that all
platforms have proper defines for implemented functions and there are no
redefinitions.
|
|
Currently {read,write}s{b,w,lq}() functions are available only on some
architectures, and there are no io{read,write}{8,16,32,64}_rep()
functions in u-boot. This patch adds generic versions that may be used
without arch-specific implementation.
Since some of added functions were already added locally in some files,
remove them to avoid redeclaration errors.
Signed-off-by: Igor Prusov <[email protected]>
|
|
Prepare v2024.01-rc3
|
|
- squashfs improvements, remove common.h in some places, assorted code
fixes, fix a few CONFIG symbol names in Kconfig files, bring in
linux's <linux/time.h> conversion functions, poplar updates, bcb
improvements.
|
