| Age | Commit message (Collapse) | Author |
|---|
|
This function is already defined in spi.h but no implementation of it
currently exists in the tree. The implementation is based on the static
function spi_set_speed_mode(). The function prototype is modified so
that an success or error condition can be returned to the caller.
Signed-off-by: Paul Barker <[email protected]>
Reviewed-by: Heinrich Schuchardt <[email protected]>
|
|
Fix the following sparse and compile time warning triggered with W=1:
drivers/spi/zynqmp_gqspi.c:286:6:
warning: no previous prototype for 'zynqmp_qspi_set_tapdelay'
[-Wmissing-prototypes]
Signed-off-by: Venkatesh Yadav Abbarapu <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michal Simek <[email protected]>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2023.01-rc1 (round 2)
xilinx:
- Add support for new Versal NET SOC
zynqmp:
- Use mdio bus for ethernet phy description
- Wire ethernet phy reset via i2c-gpio
versal:
- Config cleanup
|
|
Add support for Versal NET platform.
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/f374e9a81f2d85de1240029f3ba5f6423cfa0680.1663589964.git.michal.simek@amd.com
|
|
Trivial changes to support cadence ospi driver for Versal NET platform.
Also avoid ospi flash reset for now.
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/0789141f432189aab69bc496fe33e0218d1d7510.1663589964.git.michal.simek@amd.com
|
|
This patch adds support for spi-mem controller found on newer MediaTek SoCs
This controller supports Single/Dual/Quad SPI mode.
Reviewed-by: Simon Glass <[email protected]>
Tested-by: Daniel Golle <[email protected]>
Signed-off-by: SkyLake.Huang <[email protected]>
|
|
Signed-off-by: Tom Rini <[email protected]>
|
|
Globally replace all occurances of WATCHDOG_RESET() with schedule(),
which handles the HW_WATCHDOG functionality and the cyclic
infrastructure.
Signed-off-by: Stefan Roese <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Tested-by: Tom Rini <[email protected]> [am335x_evm, mx6cuboxi, rpi_3,dra7xx_evm, pine64_plus, am65x_evm, j721e_evm]
|
|
Driver can configure the SPI clock frequnecy to the
target value of "spi-max-frequency" property in
the device tree. The frequency is divided from HCLK,
200MHz. Usually, the ASPEED SPI clock frequency range
is between 12.5MHz and 100MHz. On AST2600, the lowest
SPI clock frequency can be about 780kHz.
Signed-off-by: Chin-Ting Kuo <[email protected]>
|
|
If "decoded-ranges" is defined in the device tree, the
driver will apply the decoded address ranges from this
property to the controller during probe stage.
This patch refers to the following OpenBMC u-boot patch.
https://patchwork.ozlabs.org/project/openbmc/list/?series=306969
Signed-off-by: Chin-Ting Kuo <[email protected]>
|
|
There are some known HW problems about decoded
range register configurations on existing AST2500 and
AST2600 platforms. Additional callback function,
adjust_decoded_sz, is added to solve these problems
on each platform. Besides, aspeed_spi_trim_decoded_size
function is added to modify overall decoded address
size for fitting the maximum AHB decoded size.
Signed-off-by: Chin-Ting Kuo <[email protected]>
|
|
From the HW point of view, the performance of
command read mode is greater than user mode slightly.
Thus, dirmap read framework is introduced to achieve
this goal. In dirmap_create, command read mode is
configured. Usually, the decoded address area with flash
size is assigned to each CS. CPU can thus access the
SPI flash as normal memory in dirmap_read function.
Signed-off-by: Chin-Ting Kuo <[email protected]>
|
|
This adds the dirmap API originally introduced in
Linux commit aa167f3fed0c
("spi: spi-mem: Add a new API to support direct mapping").
This also includes several follow-up patches and fixes.
Changes from Linux include:
* Added Kconfig option
* Changed struct device to struct udevice
* Changed struct spi_mem to struct spi_slave
This patch is obtained from the following patch
https://patchwork.ozlabs.org/project/uboot/patch/[email protected]/
The corresponding Linux kernel SHA1 is aa167f3fed0c.
Signed-off-by: Chin-Ting Kuo <[email protected]>
Signed-off-by: Sean Anderson <[email protected]>
Acked-by: Pratyush Yadav <[email protected]>
|
|
Although AST2400 is EOL officially, in order to achieve
sustainability and completeness, AST2400 part is added.
For AST2400,
- Five CSs are supported by FMC controller.
- SPI1 controller only supports single CS and there is
no address segment address register. The CE control
register of SPI1 is located at the offset 0x04 and
the 4-byte address mode control bit is bit 13 of
this register.
Signed-off-by: Chin-Ting Kuo <[email protected]>
|
|
Add ASPEED BMC FMC/SPI memory controller driver with
spi-mem interface for AST2500 and AST2600 platform.
There are three SPI memory controllers embedded in an ASPEED SoC.
- FMC: Named as Firmware Memory Controller. After AC on, MCU ROM
fetches initial device boot image from FMC chip select(CS) 0.
- SPI1: Play the role of a SPI Master controller. Or, there is a
dedicated path for HOST(X86) to access its BIOS flash mounted
under BMC. spi-aspeed-smc.c implements the control sequence when
SPI1 is a SPI master.
- SPI2: It is a pure SPI flash controller. For most scenarios, flashes
mounted under it are for pure storage purpose.
ASPEED SPI controller supports 1-1-1, 1-1-2 and 1-1-4 SPI flash mode.
Three types of command mode are supported, normal mode, command
read/write mode and user mode.
- Normal mode: Default mode. After power on, normal read command 03h or
13h is used to fetch boot image from SPI flash.
- AST2500: Only 03h command can be used after power on
or reset.
- AST2600: If FMC04[6:4] is set, 13h command is used,
otherwise, 03h command.
The address length is decided by FMC04[2:0].
- Command mode: SPI controller can send command and address
automatically when CPU read/write the related remapped
or decoded address area. The command used by this mode
can be configured by FMC10/14/18[23:16]. Also, the
address length is decided by FMC04[2:0]. This mode will
be implemented in the following patch series.
- User mode: It is a traditional and pure SPI operation, where
SPI transmission is controlled by CPU. It is the main
mode in this patch.
Each SPI controller in ASPEED SoC has its own decoded address mapping.
Within each SPI controller decoded address, driver can assign a specific
address region for each CS of a SPI controller. The decoded address
cannot overlap to each other. With normal mode and command mode, the
decoded address accessed by the CPU determines which CS is active.
When user mode is adopted, the CS decoded address is a FIFO, CPU can
send/receive any SPI transmission by accessing the related decoded
address for the target CS.
This patch only implements user mode initially. Command read/write
mode will be implemented in the following patches.
Signed-off-by: Chin-Ting Kuo <[email protected]>
|
|
Few lines are extented to next line though they can fit in 80 character
limit, align them to single line. No functional change.
Signed-off-by: Ashok Reddy Soma <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michal Simek <[email protected]>
|
|
As the flash sizes are increasing day by day, QSPI can have devices of
size > 512MB. In qspi driver we are trying to read all the data at once
using DMA.
The DMA descriptor destination size is only 29bits long.
QSPIDMA_DST_SIZE 0xFF0F0804
BITS: 1:0 Reserved to keep word alignment
BITS: 28:2 Number of 4-byte words the DMA will transfer
BITS: 31:29 Reserved: Returns 0 when read, writes ignored
So we can only transfer data of 0x1FFFFFF0(512MB minus 4bytes) bytes.
Anything above will overflow this register and will ignore higher bits
above 29 bits.
Change the DMA functionality if the requested size is greater than or
equal to 512MB to read 256MB chunks.
Signed-off-by: Ashok Reddy Soma <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michal Simek <[email protected]>
|
|
Add support for io-mode transfers. This is necessary for UBIFS to work
properly with spi-nor devices. The driver will work in IO mode when
"has-io-mode" is passed from device tree instead of DMA.
Signed-off-by: Ashok Reddy Soma <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michal Simek <[email protected]>
|
|
Add tap delays for Versal platform and re-align the tapdelays code.
Signed-off-by: Ashok Reddy Soma <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michal Simek <[email protected]>
|
|
As per driver model we should enumerate plat structure only in
of_to_plat() and should be used only in probe(). Copy required
plat structure info into priv structure in probe() and use priv
structure across the driver. So replace plat with priv structure across
the driver.
Signed-off-by: Ashok Reddy Soma <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michal Simek <[email protected]>
|
|
In cadence_spi_read_id we are using STIG mode to read flash id's.
Call cadence_qspi_apb_command_read_setup() to setup cmd, addr and data
bus width properly before cadence_qspi_apb_command_read().
Signed-off-by: Ashok Reddy Soma <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michal Simek <[email protected]>
|
|
In cadence_spi_probe, cadence_qspi_versal_flash_reset() is called to reset
the flash device. Looks like there is a mistake in previous series of
patches where it is defined as cadence_spi_versal_flash_reset() but
called as cadence_qspi_versal_flash_reset. Since there is a weak function
defined with the same name this issue was not caught.
Fix the issue by renaming cadence_spi_versal_flash_reset as
cadence_qspi_versal_flash_reset().
Signed-off-by: Ashok Reddy Soma <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michal Simek <[email protected]>
|
|
The compatible values used for device nodes representing Renesas Reduced
Pin Count Interfaces were based on preliminary versions of the Device
Tree Bindings.
Correct them in both DTSi files and drivers, to match the final DT
Bindings.
Note that there are no DT bindings for RPC-IF on RZ/A1 yet, hence the
most logical SoC-specific value is used, without specifying a
family-specific value.
Signed-off-by: Geert Uytterhoeven <[email protected]>
|
|
When programming qspi flash speed we need to check the requested flash
speed not to exceed the spi max frequency. In the current implementation
we are checking qspi ref clk instead. This commit fixes the issue by
checking the requested speed and programs the specified max frequency.
Signed-off-by: Ashok Reddy Soma <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michal Simek <[email protected]>
|
|
Add support_ops function zynq_qspi_mem_exec_op to check controller
supported operations by spi-mem framework. Current default support ops
function does not allow dummy buswidth no more than 1, unless we are
using buswidth is 4 for TX.
Signed-off-by: Ashok Reddy Soma <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michal Simek <[email protected]>
|
|
Fix dummy bytes calculation incase of valid dummy bytes when dummy
buswidth is > 1. Current dummy bytes calculation does not provide
correct dummy values for dummy buswidth > 1.
Signed-off-by: T Karthik Reddy <[email protected]>
Signed-off-by: Ashok Reddy Soma <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michal Simek <[email protected]>
|
|
Add child pre probe function in the driver. Update max_hz of priv from
spi_slave structure.
Signed-off-by: Siva Durga Prasad Paladugu <[email protected]>
Signed-off-by: Ashok Reddy Soma <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michal Simek <[email protected]>
|
|
Add support_ops function to check controller supported operations by
spi-mem framework. Current default support ops function does not allow
dummy buswidth no more than 1, unless we are using buswidth is 4 for TX.
In order to support dummy buswidth > 1 by spi-nor framework we are adding
explicit support_ops to check controller supported operations.
Fix dummy bytes calculation incase of valid dummy bytes when dummy
buswidth is > 1. Current dummy bytes calculation does not provide
correct dummy values for dummy buswidth > 1.
Signed-off-by: T Karthik Reddy <[email protected]>
Signed-off-by: Ashok Reddy Soma <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michal Simek <[email protected]>
|
|
Add support for spi memory operations for xilinx AXI qspi driver.
This provides an high-level interface to execute SPI memory
operations by the controller.
Remove existing spi transfer based implementation and use
spi memory based exec_op() implementation for qspi IO operations.
Simplified existing startup_block implementation.
Signed-off-by: T Karthik Reddy <[email protected]>
Signed-off-by: Ashok Reddy Soma <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michal Simek <[email protected]>
|
|
The SPI controllers in the Allwinner F1Cx00 series of SoCs are
compatible to the H3 IP. The only difference in the integration is
the missing mod clock in the F1C100, instead the SPI clock is directly
derived from the AHB clock.
We *should* be able to model this through the DT, but the addition of
get_rate() requires quite some refactoring, so it's not really worth in
this simple case: We programmed both the PLL_PERIPH to 600 MHz and the
PLL/AHB divider to 3 in the SPL, so we know the SPI base clock is 200
MHz. Since we used a hard coded fixed clock rate of 24 MHz for all the
other SoCs so far, we can as well do the same for the F1C100.
Define the SPI input clock and maximum frequency differently when
compiling for the F1C100 SoC.
Also adjust the power-of-2 divider programming, because that uses a
"minus one" encoding, compared to the other SoCs.
This allows to enable SPI flash support for the F1C100 boards.
Signed-off-by: Andre Przywara <[email protected]>
|
|
The current SPI clock divider calculation has two problems:
- We use a normal round-down division, which results in a divider
typically being too small, resulting in a too high frequency on the bus.
- The calculaction for the power-of-two divider is very inaccurate, and
again rounds down, which might lead to wild bus frequencies.
This wasn't a real problem so far, since most chips can handle slightly
higher bus frequencies just fine. Also the actual speed was mostly lost
anyway, due to release_bus() reseting the device. And the power-of-2
calculation was probably never used, because it only applies to
frequencies below 47 KHz.
However this will become a problem for the F1C100s support, due to its
much higher base frequency.
Calculate a safe divider correctly (using round-up), and re-use that
value when calculating the power-of-2 value. We also separate the
maximum frequency and the input clock on the way, since they will be
different for the F1C100s.
Signed-off-by: Andre Przywara <[email protected]>
|
|
As George rightfully pointed out [1], the spi-sunxi driver programs the
speed and mode settings only when the respective functions are called,
but this gets lost over a call to release_bus(). That asserts the
reset line, thus forces each SPI register back to its default value.
Adding to that, trying to program SPI_CCR and SPI_TCR might be pointless
in the first place, when the reset line is still asserted (before
claim_bus()), so those setting won't apply most of the time. In reality
I see two nested claim_bus() calls for the first use, so settings between
the two would work (for instance for the initial "sf probe"). However
later on the speed setting is not programmed into the hardware anymore.
So far we get away with that default frequency, because that is a rather
tame 24 MHz, which most SPI flash chips can handle just fine.
Move the actual register programming into a separate function, and use
.set_speed and .set_mode just to set the variables in our priv structure.
Then we only call this new function in claim_bus(), when we are sure
that register accesses actually work and are preserved.
[1] https://lore.kernel.org/u-boot/[email protected]/
Signed-off-by: Andre Przywara <[email protected]>
Reported-by: George Hilliard <[email protected]>
|
|
The current detection of RX FIFO depth seems to be not reliable, and
XCH will self-clear when a transfer is done.
Check XCH bit when polling for transfer finish.
Signed-off-by: Icenowy Zheng <[email protected]>
Reviewed-by: Andre Przywara <[email protected]>
Signed-off-by: Andre Przywara <[email protected]>
|
|
This patch makes mt7621_spi driver available for MediaTek MT7621 SoC
Signed-off-by: Weijie Gao <[email protected]>
|
|
When the requested flash speed is 0, the baudrate division for the
requested speed causing drop in the performance. So set the ospi flash
to operate at max frequency when requested speed is zero.
Signed-off-by: T Karthik Reddy <[email protected]>
Signed-off-by: Ashok Reddy Soma <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michal Simek <[email protected]>
|
|
On versal platform, enable apb linear mode for apb read and write
execute operations amd disable it when using dma reads. This is done by
xilinx_pm_request() secure calls when CONFIG_ZYNQMP_FIRMWARE is enabled,
else we use direct raw reads and writes in case of mini U-Boot.
Signed-off-by: T Karthik Reddy <[email protected]>
Signed-off-by: Ashok Reddy Soma <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michal Simek <[email protected]>
|
|
When flash operated at non default mode like DDR, flash need to be reset
to operate in SDR mode to read flash ids by spi-nor framework. Reset the
flash to the default state before using the flash. This reset is handled
by a gpio driver, in case of mini U-Boot as gpio driver is disabled, we
do raw read and write access by the registers.
Versal platform utilizes spi calibration for read delay programming, so
incase by default read delay property is set in DT. We make sure not to
use read delay from DT by overwriting read_delay with -1.
Signed-off-by: T Karthik Reddy <[email protected]>
Signed-off-by: Ashok Reddy Soma <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michal Simek <[email protected]>
|
|
Add support for cadence ospi driver for Versal platform. This driver
provides support for DMA read operation which utilizes cadence qspi
driver.
If "cdns,is-dma" DT property is specified use dma for read operation
from cadence_qspi driver. As cadence_qspi_apb_dma_read() is defined in
cadence_ospi_versal driver add a weak function defination in
cadence_qspi driver.
Signed-off-by: T Karthik Reddy <[email protected]>
Signed-off-by: Ashok Reddy Soma <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michal Simek <[email protected]>
|
|
Move all the cadence macros from cadence_qspi_apb.c to cadence_qspi.h
file.
Signed-off-by: T Karthik Reddy <[email protected]>
Signed-off-by: Ashok Reddy Soma <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michal Simek <[email protected]>
|
|
The GXP supports 3 separate SPI interfaces to accommodate the system
flash, core flash, and other functions. The SPI engine supports variable
clock frequency, selectable 3-byte or 4-byte addressing and a
configurable x1, x2, and x4 command/address/data modes. The memory
buffer for reading and writing ranges between 256 bytes and 8KB. This
driver supports access to the core flash.
Signed-off-by: Nick Hawkins <[email protected]>
|
|
Merge in v2022.07-rc5.
|
|
Replace reference to the correct name STMicroelectronics
Signed-off-by: Patrick Delaunay <[email protected]>
Reviewed-by: Heiko Schocher <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
|
The nxp_fspi_default_setup() is only ever called from nxp_fspi_probe(),
where the IP clock are initially disabled. Drop the second disabling of
clock to prevent clock enable/disable imbalance reported by clock core:
"
clk qspi_root_clk already disabled
"
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
|
|
There is a TX-FIFO and Shift Register empty(TFES) status
bit in spi controller. This commit checks the TFES bit
to wait the TX transfer completes.
Signed-off-by: Masahisa Kojima <[email protected]>
Signed-off-by: Satoru Okamoto <[email protected]>
Acked-by: Jassi Brar <[email protected]>
|
|
DMSTART bit must not be set while there is active transfer.
This commit sets the DMSTART bit only when the transfer begins.
Signed-off-by: Masahisa Kojima <[email protected]>
Signed-off-by: Satoru Okamoto <[email protected]>
Acked-by: Jassi Brar <[email protected]>
|
|
synquacer_cs_set() function does not wait the chip select
is deasserted when the driver sets the DMSTOP to deselect
the slave.
This commit checks the Slave Select Released(SRS) bit to wait
until the slave is deselected.
Signed-off-by: Masahisa Kojima <[email protected]>
Signed-off-by: Satoru Okamoto <[email protected]>
Acked-by: Jassi Brar <[email protected]>
|
|
"busy" variable is ORed without being initialized,
must be zeroed before use.
Signed-off-by: Masahisa Kojima <[email protected]>
Signed-off-by: Satoru Okamoto <[email protected]>
Acked-by: Jassi Brar <[email protected]>
|
|
Move legacy spi_get_bus_and_cs() code to _spi_get_bus_and_cs().
Add new spi_get_bus_and_cs() implementation which rely on DT
for speed and mode and don't need any drv_name nor dev_name
parameters. This will prepare the ground for next patch.
Update all callers to use _spi_get_bus_and_cs() to keep the
same behavior.
Signed-off-by: Patrice Chotard <[email protected]>
Cc: Marek Behun <[email protected]>
Cc: Jagan Teki <[email protected]>
Cc: Vignesh R <[email protected]>
Cc: Joe Hershberger <[email protected]>
Cc: Ramon Fried <[email protected]>
Cc: Lukasz Majewski <[email protected]>
Cc: Marek Vasut <[email protected]>
Cc: Wolfgang Denk <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Stefan Roese <[email protected]>
Cc: "Pali Rohár" <[email protected]>
Cc: Konstantin Porotchkin <[email protected]>
Cc: Igal Liberman <[email protected]>
Cc: Bin Meng <[email protected]>
Cc: Pratyush Yadav <[email protected]>
Cc: Sean Anderson <[email protected]>
Cc: Anji J <[email protected]>
Cc: Biwen Li <[email protected]>
Cc: Priyanka Jain <[email protected]>
Cc: Chaitanya Sakinam <[email protected]>
|
|
Waiting for SR_BUSY bit when receiving a new command is not needed.
SR_BUSY bit is already managed in the previous command treatment.
Signed-off-by: Patrice Chotard <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
|
|
Currently, SR_TCF flag is checked in case there is data, this criteria
is not correct.
SR_TCF flags is set when programmed number of bytes have been transferred
to the memory device ("bytes" comprised command and data send to the
SPI device).
So even if there is no data, we must check SR_TCF flag.
Signed-off-by: Patrice Chotard <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
|
