| Age | Commit message (Collapse) | Author |
|---|
|
This driver is able to reconfigure OTG controller into HOST mode.
Board can add board-specific initialization as board_prepare_usb().
It requires USB_ULPI_VIEWPORT enabled in board configuration.
Signed-off-by: Mateusz Kulikowski <[email protected]>
Acked-by: Marek Vasut <[email protected]>
Tested-by: Simon Glass <[email protected]>
|
|
Now, all this driver does can be covered by the generic EHCI driver
(drivers/usb/host/ehci-generic.c). UniPhier SoCs have switched to
use it. Delete this driver rather than bothering to convert it to
Driver Model.
Signed-off-by: Masahiro Yamada <[email protected]>
Acked-by: Marek Vasut <[email protected]>
|
|
This driver is meant to be used with any OHCI-compatible host
controller in case if there's no need for platform-specific
glue such as setup of controller or PHY's power mode via
GPIOs etc.
Signed-off-by: Alexey Brodkin <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Marek Vasut <[email protected]>
|
|
This driver is meant to be used with any EHCI-compatible host
controller in case if there's no need for platform-specific
glue such as setup of controller or PHY's power mode via
GPIOs etc.
Signed-off-by: Alexey Brodkin <[email protected]>
Cc: Stephen Warren <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Marek Vasut <[email protected]>
|
|
Added USB XHCI driver support for zynqmp.
Signed-off-by: Siva Durga Prasad Paladugu <[email protected]>
|
|
Extend ehci-mx6 usb driver to support imx7d usb
Signed-off-by: Adrian Alonso <[email protected]>
|
|
Incorporate USB driver from legacy LPCLinux NXP BSP.
The files taken from the legacy patch are:
- lpc32xx USB driver
- lpc3250 header file USB registers definition.
The legacy driver was updated and clean-up as part of the integration with the latest u-boot.
Signed-off-by: Sylvain Lemieux <[email protected]>
Acked-by: Marek Vasut <[email protected]>
Tested-by: Vladimir Zapolskiy <[email protected]>
|
|
Add xhci driver support for all FSL socs
Signed-off-by: Ramneek Mehresh <[email protected]>
|
|
Add support for DWC3 XHCI controller driver
Signed-off-by: Ramneek Mehresh <[email protected]>
|
|
This commit adds support for the OHCI companion controller, which makes
usb-1 devices directly plugged into to usb root port work.
Note for now this switches usb-keyboard support for sunxi back from int-queue
support to the old interrupt polling method. Adding int-queue support to the
ohci code and switching back to int-queue support is in the works.
Signed-off-by: Hans de Goede <[email protected]>
Acked-by: Marek Vasut <[email protected]>
Acked-by: Ian Campbell <[email protected]>
|
|
This driver adds support for the USB peripheral on Freescale Vybrid
SoC's.
Signed-off-by: Sanchayan Maity <[email protected]>
|
|
This driver supports using emulation devices to provide a USB bus within
sandbox.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
Add a uclass that can represent a USB controller. For now we do not create
devices for things attached to the controller. This will be added later.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
Support xHCI host driver used on Panasonic UniPhier platform.
Signed-off-by: Masahiro Yamada <[email protected]>
Acked-by: Marek Vasut <[email protected]>
|
|
Add a driver which locates the available XHCI controllers on the PCI bus
and makes them available.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
Support EHCI host driver used on Panasonic UniPhier platform.
Since Device Tree is not supported on UniPhier yet, the base address
of USB cores are passed from board files (platdevice.c).
TODO for me:
Move the base address to device trees.
Signed-off-by: Masahiro Yamada <[email protected]>
Acked-by: Marek Vasut <[email protected]>
|
|
|
|
Add support of usb xhci. xHCI controls all USB speeds of the Host
mode, that is, the SS through the SS PHY, as well as the HS, FS, and
LS through the USB2 PHY. xHCI replaces and supersedes all previous
host HCIs (HS-only EHCI, FS/LS OHCI and UHCI), and is therefore not
backwards compatible with any of them. The USB3SS’s USB Controller is
fully compliant with xHC.
Acked-by: Vitaly Andrianov <[email protected]>
Signed-off-by: WingMan Kwok <[email protected]>
Signed-off-by: Ivan Khoronzhuk <[email protected]>
|
|
This is the USB host controller used on the Altera SoCFPGA and Raspbery Pi.
This code has three checkpatch warnings, but to make sure it stays at least
readable and clear, these are not fixed. These bugs are in the USB request
handling combinatorial logic, so any abstracting of those is out of question.
Tested on DENX MCV (Altera SoCFPGA 5CSFXC6C6U23C8N) and RPi B+ (BCM2835).
Signed-off-by: Oleksandr Tymoshenko <[email protected]>
Signed-off-by: Stephen Warren <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
Cc: Chin Liang See <[email protected]>
Cc: Dinh Nguyen <[email protected]>
Acked-by: Pavel Machek <[email protected]>
Cc: Vince Bridgers <[email protected]>
Tested-by: Dinh Nguyen <[email protected]>
|
|
The Allwinner aka sunxi SoCs have one or more USB host controllers.
This adds a driver for their EHCI.
Signed-off-by: Roman Byshko <[email protected]>
Acked-by: Marek Vasut <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
|
|
This patch returns back support for old ep93xx processors family
Signed-off-by: Sergey Kostanbaev <[email protected]>
Cc: [email protected]
|
|
Added USB host driver for zynq.
Signed-off-by: Siva Durga Prasad Paladugu <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
The rmobile SoC has usb host controller.
This supports USB controllers listed in the R8A7790, R8A7791 and R8A7740.
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
The driver is no longer used, remove it.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Albert Aribaud <[email protected]>
Cc: Michael Schwingen <[email protected]>
Cc: Tom Rini <[email protected]>
|
|
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Add the OMAP file for the xHCI Host controller
This code will initilialize the proper components within the
OMAP5 to enable the xHCI host controller.
Signed-off-by: Dan Murphy <[email protected]>
|
|
This adds driver layer for xHCI controller in Samsung's
exynos5 soc. This interacts with xHCI host controller stack.
Signed-off-by: Vikas C Sajjan <[email protected]>
Signed-off-by: Vivek Gautam <[email protected]>
Cc: Julius Werner <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Minkyu Kang <[email protected]>
Cc: Dan Murphy <[email protected]>
Cc: Marek Vasut <[email protected]>
|
|
This adds stack layer for eXtensible Host Controller Interface
which facilitates use of USB 3.0 in host mode.
Adapting xHCI host controller driver in linux-kernel
by Sarah Sharp to needs in u-boot.
Initial porting from Linux kernel version 3.4, with following
top commit history of drivers/usb/host/xhci* :
cf84055 xHCI: Cleanup isoc transfer ring when TD length mismatch found
This adds the basic xHCI host controller driver with bare minimum
features:
- Control/Bulk transfer support has been added with required
infrastructure for necessary xHC data structures.
- Stream protocol hasn't been supported yet.
- No support for quirky devices has been added.
Signed-off-by: Vikas C Sajjan <[email protected]>
Signed-off-by: Julius Werner <[email protected]>
Signed-off-by: Vivek Gautam <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Minkyu Kang <[email protected]>
Cc: Dan Murphy <[email protected]>
Cc: Marek Vasut <[email protected]>
|
|
Signed-off-by: Wolfgang Denk <[email protected]>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <[email protected]>
|
|
This patch adds support to both Faraday FUSBH200 and FOTG210,
the differences between Faraday EHCI and standard EHCI are
listed bellow:
1. The PORTSC starts at 0x30 instead of 0x44.
2. The CONFIGFLAG(0x40) is not only un-implemented, and
also has its address space removed.
3. Faraday EHCI is a TDI design, but it doesn't
compatible with the general TDI implementation
found at both U-Boot and Linux.
4. The ISOC descriptors differ from standard EHCI in
several ways. But since U-boot doesn't support ISOC,
we don't have to worry about that.
Signed-off-by: Kuo-Jung Su <[email protected]>
CC: Marek Vasut <[email protected]>
|
|
Following the removal of the smdk6400 board, the s3c64xx SoC becomes unused, so
remove associated code. It will still be possible to restore it later from the
Git history if necessary.
Signed-off-by: Benoît Thébaudeau <[email protected]>
|
|
Add EHCI support for spear boards
Signed-off-by: Armando Visconti <[email protected]>
Signed-off-by: Vipin Kumar <[email protected]>
|
|
Signed-off-by: Marek Vasut <[email protected]>
Cc: David Müller <[email protected]>
Cc: Minkyu Kang <[email protected]>
Cc: Wolfgang Denk <[email protected]>
Cc: Albert Aribaud <[email protected]>
Cc: U-Boot DM <[email protected]>
|
|
Also enable the ohci port on hawkboard. These additions result in an
increased u-boot size -- adjust the same accordingly in the board's
config.
Move the usb header for da8xx platforms under arch-davinci.
Signed-off-by: Sughosh Ganu <[email protected]>
|
|
This patch incorates the review comments given by Minkyu Kang for
EHCI support on EXYNOS
Signed-off-by: Rajeshwari Shinde <[email protected]>
|
|
Some Atmel SoC support USB EHCI, add the EHCI driver to support it.
To enable the USB EHCI, add the following configuration options into
board relative configuration file and remove USB OHCI options.
#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_ATMEL
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 2
Signed-off-by: Bo Shen <[email protected]>
Acked-by: Marek Vasut <[email protected]>
Signed-off-by: Andreas Bießmann <[email protected]>
|
|
This patch adds ehci driver support for s5p.
Signed-off-by: Vivek Gautam <[email protected]>
Signed-off-by: Rajeshwari Shinde <[email protected]>
|
|
This adds basic support for the Tegra2 USB controller. Board files should
call board_usb_init() to set things up.
Configuration is performed through the FDT, with aliases used to set the
order of the ports, like this fragment:
aliases {
/* This defines the order of our USB ports */
usb0 = "/usb@0xc5008000";
usb1 = "/usb@0xc5000000";
};
drivers/usb/host files ONLY: Acked-by: Remy Bohmer <[email protected]>
Signed-off-by: Simon Glass <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
Currently, only USB Host 1 is supported.
Cc: Remy Bohmer <[email protected]>
Signed-off-by: Wolfgang Grandegger <[email protected]>
|
|
This patch adds support for USB EHCI driver for Armada100 SOCs.
Signed-off-by: Ajay Bhargav <[email protected]>
|
|
Taken from Beagle code. Tested on mcx board (AM3517-based).
Signed-off-by: Ilya Yanok <[email protected]>
Tested-by: Stefano Babic <[email protected]>
|
|
Signed-off-by: Albert ARIBAUD <[email protected]>
Signed-off-by: Prafulla Wadaskar <[email protected]>
|
|
It's derived from ehci-mxc and uses the header files of the
ehci-fsl interface. The callback board_ehci_hcd_init() has
been introduced to allow for board-specific setup when USB
is started.
Signed-off-by: Wolfgang Grandegger <[email protected]>
CC: Stefano Babic <[email protected]>
CC: Remy Bohmer <[email protected]>
|
|
This driver supports both EHCI ports on the i.MX28 CPU.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Wolfgang Denk <[email protected]>
Cc: Detlev Zundel <[email protected]>
Cc: Remy Bohmer <[email protected]>
|
|
Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils. As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".
This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.
The name of each former library archive is preserved except for
extensions which change from ".a" to ".o". This commit updates
references accordingly where needed, in particular in some linker
scripts.
This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols. Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.
Signed-off-by: Sebastien Carlier <[email protected]>
|
|
Signed-off-by: Francesco Rendine <[email protected]>
Signed-off-by: Damien Dusha <[email protected]>
Signed-off-by: Anatolij Gustschin <[email protected]>
Coding style cleanup; slight file restructuring.
Signed-off-by: Wolfgang Denk <[email protected]>
Acked-by: Remy Bohmer <[email protected]>
|
|
The patch adds the EHCI controller for the i.MX31 Soc.
Signed-off-by: Stefano Babic <[email protected]>
|
|
Currently ppc440epx uses OHCI for USB full-speed support. This change adds
support for EHCI.
Signed-off-by: Chris Zhang <[email protected]>
|
|
This driver is tested on Sheevaplug platform
Signed-off-by: Prafulla Wadaskar <[email protected]>
Signed-off-by: Remy Bohmer <[email protected]>
|
|
move to linux usb driver organisation
as following
drivers/usb/gadget
drivers/usb/host
drivers/usb/musb
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
Signed-off-by: Remy Bohmer <[email protected]>
|
