| Age | Commit message (Collapse) | Author |
|---|
|
We have changed to use dwc3 generic driver for usb3.0 host, so the
legacy Rockchip's xHCI driver is not needed, and drop it.
Signed-off-by: Frank Wang <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
This patch is used to support the on-chip xHCI controller on
MediaTek SoCs, currently control/bulk/interrupt transfers are
supported.
Signed-off-by: Chunfeng Yun <[email protected]>
Signed-off-by: Frank Wunderlich <[email protected]>
Reviewed-by: Weijie Gao <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
Base driver for Broadcom xHCI controllers
Signed-off-by: Bharat Kumar Reddy Gooty <[email protected]>
Signed-off-by: Rayagonda Kokatanur <[email protected]>
Signed-off-by: Vladimir Olovyannikov <[email protected]>
|
|
This driver is not used anymore.
Signed-off-by: Jean-Jacques Hiblot <[email protected]>
|
|
add new DM based PCI driver ohci-pci for PCI-based
OHCI USB support.
Signed-off-by: Heiko Schocher <[email protected]>
|
|
Now Allwinner platform is all set to use Generic USB
controller drivers, so remove the legacy sunxi drivers.
Signed-off-by: Jagan Teki <[email protected]>
Acked-by: Maxime Ripard <[email protected]>
|
|
The keystone platforms can use the generic DC3 driver. Removing the
keystone-spcecific xchi driver and add the configuration options to enable
the generic DWC3 driver on all K2 platforms.
Signed-off-by: Jean-Jacques Hiblot <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Common USB code is built whenever USB is enabled (in non-SPL builds).
The USB uclass is built whenever (SPL_)DM_USB is enabled. Both need to
be independent from CMD_USB.
Signed-off-by: Sven Schwermer <[email protected]>
|
|
This allows building the SPL without driver model for USB. Since
CONFIG_SPL_DM_USB is enabled if and only if CONFIG_DM_USB was enabled
before, this patch does not change the build behaviour.
Signed-off-by: Sven Schwermer <[email protected]>
|
|
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <[email protected]>
|
|
This is a port of the dwc3-of-simple driver from Linux to enable/deassert
clock and resets of a simple DWC3 Controller HW glue.
Signed-off-by: Neil Armstrong <[email protected]>
|
|
ppc4xx support was removed some time ago. Lets remove the now unused
EHCI driver and all its references for this platform as well.
Signed-off-by: Stefan Roese <[email protected]>
Cc: Heinrich Schuchardt <[email protected]>
Cc: Marek Vasut <[email protected]>
|
|
The isp116x-hcd driver is extremely long unused, so just remove it.
Cc: Marek Vasut <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Add firmware V3, firmware loader and XHCI glue for the Renesas R-Car
Gen3 SoCs XHCI controller. Thus far only the R-Car Gen3 R8A7795 ES2.0+
and R8A7796 are supported.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Nobuhiro Iwamatsu <[email protected]>
Cc: Bin Meng <[email protected]>
|
|
Since we use EHCI generic driver on RCar Gen3 , this driver is useless.
Remove it.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Nobuhiro Iwamatsu <[email protected]>
Acked-by: Nobuhiro Iwamatsu <[email protected]>
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
This patch adds the ST glue logic to manage the DWC3 HC
on STiH407 SoC family. It configures the internal glue
logic and syscfg registers.
Part of this code been extracted from kernel.org driver
(drivers/usb/dwc3/dwc3-st.c)
Signed-off-by: Patrice Chotard <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
There was for long time no activity in the mpx5xxx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in mpc5xxx,
so remove it.
Signed-off-by: Heiko Schocher <[email protected]>
|
|
This is not used anymore. Drop it.
Signed-off-by: Simon Glass <[email protected]>
|
|
Add a USB controller driver for the EHCI block in R8A7795/R8A7796 SoC.
This is a stopgap measure until we have proper DT support, clock and
reset framework in place, at which point we can switch to ehci-generic.
Signed-off-by: Hiroyuki Yokoyama <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
Cc: Hiroyuki Yokoyama <[email protected]>
Cc: Nobuhiro Iwamatsu <[email protected]>
Reviewed-by: Nobuhiro Iwamatsu <[email protected]>
|
|
In order to be able to migrate the various SoC EHCI CONFIG options we
first need to finish the switch from CONFIG_USB_EHCI to
CONFIG_USB_EHCI_HCD.
Cc: Marek Vasut <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
This patch adds DM based support for the xHCI USB 3.0 controller
integrated in the Armada 3700 SoC. It may be extended to be used
by other MVEBU SoCs as well.
Signed-off-by: Stefan Roese <[email protected]>
Cc: Nadav Haklai <[email protected]>
Cc: Kostya Porotchkin <[email protected]>
Cc: Wilson Ding <[email protected]>
Cc: Victor Gu <[email protected]>
Cc: Hua Jing <[email protected]>
Cc: Terry Zhou <[email protected]>
Cc: Hanna Hawa <[email protected]>
Cc: Haim Boot <[email protected]>
Acked-by: Marek Vasut <[email protected]>
|
|
This patch add support for rockchip dwc3 controller, which corresponding
to the two type-C port on rk3399 evb.
Only support usb2.0 currently for we have not enable the usb3.0 phy
driver and PD(fusb302) driver.
Signed-off-by: MengDongyang <[email protected]>
Signed-off-by: Kever Yang <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
This driver has not been converted to Driver Model, and it is an
obstacle to migrate other block device drivers. Remove it for now.
The UniPhier SoCs already use a DM-based EHCI driver, so now
ARCH_UNIPHIER can select DM_USB.
These two changes must be done atomically because removing the
legacy driver causes a build error.
Signed-off-by: Masahiro Yamada <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
Move CONFIG_USB_XHCI to defconfig files for all boards, renaming it
into CONFIG_USB_XHCI_HCD.
As commented in the help of "config USB_XHCI" entry, this has been
a TODO for a long time; now CONFIG_USB_XHCI_HCD and CONFIG_USB_XHCI
have been unified in favor of the former.
Note:
Some boards define CONFIG_USB_XHCI in their headers without
CONFIG_USB, which does not meet the "depends on" in Kconfig.
I added CONFIG_USB=y for those boards when converting.
Otherwise, they would fail to build.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
This driver is able to reconfigure OTG controller into HOST mode.
Board can add board-specific initialization as board_prepare_usb().
It requires USB_ULPI_VIEWPORT enabled in board configuration.
Signed-off-by: Mateusz Kulikowski <[email protected]>
Acked-by: Marek Vasut <[email protected]>
Tested-by: Simon Glass <[email protected]>
|
|
Now, all this driver does can be covered by the generic EHCI driver
(drivers/usb/host/ehci-generic.c). UniPhier SoCs have switched to
use it. Delete this driver rather than bothering to convert it to
Driver Model.
Signed-off-by: Masahiro Yamada <[email protected]>
Acked-by: Marek Vasut <[email protected]>
|
|
This driver is meant to be used with any OHCI-compatible host
controller in case if there's no need for platform-specific
glue such as setup of controller or PHY's power mode via
GPIOs etc.
Signed-off-by: Alexey Brodkin <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Marek Vasut <[email protected]>
|
|
This driver is meant to be used with any EHCI-compatible host
controller in case if there's no need for platform-specific
glue such as setup of controller or PHY's power mode via
GPIOs etc.
Signed-off-by: Alexey Brodkin <[email protected]>
Cc: Stephen Warren <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Marek Vasut <[email protected]>
|
|
Added USB XHCI driver support for zynqmp.
Signed-off-by: Siva Durga Prasad Paladugu <[email protected]>
|
|
Extend ehci-mx6 usb driver to support imx7d usb
Signed-off-by: Adrian Alonso <[email protected]>
|
|
Incorporate USB driver from legacy LPCLinux NXP BSP.
The files taken from the legacy patch are:
- lpc32xx USB driver
- lpc3250 header file USB registers definition.
The legacy driver was updated and clean-up as part of the integration with the latest u-boot.
Signed-off-by: Sylvain Lemieux <[email protected]>
Acked-by: Marek Vasut <[email protected]>
Tested-by: Vladimir Zapolskiy <[email protected]>
|
|
Add xhci driver support for all FSL socs
Signed-off-by: Ramneek Mehresh <[email protected]>
|
|
Add support for DWC3 XHCI controller driver
Signed-off-by: Ramneek Mehresh <[email protected]>
|
|
This commit adds support for the OHCI companion controller, which makes
usb-1 devices directly plugged into to usb root port work.
Note for now this switches usb-keyboard support for sunxi back from int-queue
support to the old interrupt polling method. Adding int-queue support to the
ohci code and switching back to int-queue support is in the works.
Signed-off-by: Hans de Goede <[email protected]>
Acked-by: Marek Vasut <[email protected]>
Acked-by: Ian Campbell <[email protected]>
|
|
This driver adds support for the USB peripheral on Freescale Vybrid
SoC's.
Signed-off-by: Sanchayan Maity <[email protected]>
|
|
This driver supports using emulation devices to provide a USB bus within
sandbox.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
Add a uclass that can represent a USB controller. For now we do not create
devices for things attached to the controller. This will be added later.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
Support xHCI host driver used on Panasonic UniPhier platform.
Signed-off-by: Masahiro Yamada <[email protected]>
Acked-by: Marek Vasut <[email protected]>
|
|
Add a driver which locates the available XHCI controllers on the PCI bus
and makes them available.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
Support EHCI host driver used on Panasonic UniPhier platform.
Since Device Tree is not supported on UniPhier yet, the base address
of USB cores are passed from board files (platdevice.c).
TODO for me:
Move the base address to device trees.
Signed-off-by: Masahiro Yamada <[email protected]>
Acked-by: Marek Vasut <[email protected]>
|
|
|
|
Add support of usb xhci. xHCI controls all USB speeds of the Host
mode, that is, the SS through the SS PHY, as well as the HS, FS, and
LS through the USB2 PHY. xHCI replaces and supersedes all previous
host HCIs (HS-only EHCI, FS/LS OHCI and UHCI), and is therefore not
backwards compatible with any of them. The USB3SS’s USB Controller is
fully compliant with xHC.
Acked-by: Vitaly Andrianov <[email protected]>
Signed-off-by: WingMan Kwok <[email protected]>
Signed-off-by: Ivan Khoronzhuk <[email protected]>
|
|
This is the USB host controller used on the Altera SoCFPGA and Raspbery Pi.
This code has three checkpatch warnings, but to make sure it stays at least
readable and clear, these are not fixed. These bugs are in the USB request
handling combinatorial logic, so any abstracting of those is out of question.
Tested on DENX MCV (Altera SoCFPGA 5CSFXC6C6U23C8N) and RPi B+ (BCM2835).
Signed-off-by: Oleksandr Tymoshenko <[email protected]>
Signed-off-by: Stephen Warren <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
Cc: Chin Liang See <[email protected]>
Cc: Dinh Nguyen <[email protected]>
Acked-by: Pavel Machek <[email protected]>
Cc: Vince Bridgers <[email protected]>
Tested-by: Dinh Nguyen <[email protected]>
|
|
The Allwinner aka sunxi SoCs have one or more USB host controllers.
This adds a driver for their EHCI.
Signed-off-by: Roman Byshko <[email protected]>
Acked-by: Marek Vasut <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
|
|
This patch returns back support for old ep93xx processors family
Signed-off-by: Sergey Kostanbaev <[email protected]>
Cc: [email protected]
|
|
Added USB host driver for zynq.
Signed-off-by: Siva Durga Prasad Paladugu <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
The rmobile SoC has usb host controller.
This supports USB controllers listed in the R8A7790, R8A7791 and R8A7740.
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
The driver is no longer used, remove it.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Albert Aribaud <[email protected]>
Cc: Michael Schwingen <[email protected]>
Cc: Tom Rini <[email protected]>
|
|
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Add the OMAP file for the xHCI Host controller
This code will initilialize the proper components within the
OMAP5 to enable the xHCI host controller.
Signed-off-by: Dan Murphy <[email protected]>
|
