| Age | Commit message (Collapse) | Author |
|---|
|
Debug message was showing timeout value which was passed to start
function but there is a checking if this value can be setup.
The patch is moving this debug printf function below checking.
Signed-off-by: Michal Simek <[email protected]>
|
|
Send address cycles as per value read from onfi parameter
page for Read and write commands instead of using a
hard coded value. This may vary for different parts and
hence use it from onfi parameter page value.
Signed-off-by: Siva Durga Prasad Paladugu <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
This patch adds support for 16-bit buswidth by determining
the bus width based on mio configuration.
Signed-off-by: Siva Durga Prasad Paladugu <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
There is no need to have arm hardware header in this driver.
Signed-off-by: Michal Simek <[email protected]>
|
|
This driver was tested on Xilinx ZynqMP SoC.
Signed-off-by: Michal Simek <[email protected]>
|
|
In v2018 the patch
"dm: ahci: Correct uclass private data"
(sha1: bfc1c6b4838501d10aa48c0e92eaf70976f4b2dd)
was causing an issue for ceva_sata.
But this issue is not in v2018.05-rc1 but still converting to
UCLASS_AHCI would make more sense.
Signed-off-by: Michal Simek <[email protected]>
|
|
Declaration of indirect PCI bridges is not compatible with DM: Both
define PCI operations, but in different ways. Hence, don't use indirect
bridges if DM is active.
Signed-off-by: Mario Six <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Add a driver for RXAUI control on IHS FPGAs.
Signed-off-by: Mario Six <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Add a driver for the ICS8N3QV01 Quad-Frequency Programmable VCXO.
Signed-off-by: Mario Six <[email protected]>
|
|
|
|
|
|
This patch adds the driver for the Amlogic Meson Successive Approximation
Register (SAR) A/D Converter based on the Linux IIO driver thanks to the
great work of Martin Blumenstingl.
The driver has been adapted to U-Boot and the ADC UClass.
This patch depends on the regmap "regmap: add regmap_update_bits() helper"
patch and has been tested using the newly introducted "adc" CLI command
in the "cmd: add ADC cli commands" patch.
Signed-off-by: Neil Armstrong <[email protected]>
|
|
Add the regmap_update_bits() to simply the read/modify/write of registers
in a single command. The function is taken from Linux regmap
implementation.
Signed-off-by: Neil Armstrong <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Add VREF clock gating, that may be used by STM32 VREFBUF regulator.
Signed-off-by: Fabrice Gasnier <[email protected]>
Signed-off-by: Patrice Chotard <[email protected]>
|
|
Add regulator driver for STM32 voltage reference buffer which can be
used as voltage reference for ADCs, DACs and external components through
dedicated VREF+ pin.
Signed-off-by: Fabrice Gasnier <[email protected]>
Signed-off-by: Patrice Chotard <[email protected]>
|
|
Add regulator bindings to get access to regulator managed
by drivers/power/regulator/stpmu1.c regulator driver.
Signed-off-by: Christophe Kerello <[email protected]>
Signed-off-by: Patrick Delaunay <[email protected]>
Signed-off-by: Patrice Chotard <[email protected]>
|
|
Enable support for the regulator functions of the STPMU1X PMIC. The
driver implements get/set api for the various BUCKS and LDOs supported
by the PMIC device. This driver is controlled by a device tree node
which includes voltage limits.
Signed-off-by: Christophe Kerello <[email protected]>
Signed-off-by: Patrick Delaunay <[email protected]>
Signed-off-by: Patrice Chotard <[email protected]>
|
|
When a pin is muxed to a peripheral or as a GPIO, the only
configuration that can be set is the pullup. It is too restrictive
so this patch allows to give a full configuration.
Signed-off-by: Ludovic Desroches <[email protected]>
|
|
Add PCIe driver for Intel FPGA PCIe IP. This driver operates the PCIe IP in
rootport mode only, the EP mode is not supported. The driver is tested
with the Intel e1000e NIC driver.
Signed-off-by: Ley Foon Tan <[email protected]>
|
|
The pinctrl bindings has changed for Amlogic Meson SoCs since Linux 4.13,
update the pinctrl driver to take this in account.
Signed-off-by: Neil Armstrong <[email protected]>
|
|
On all STM32F4 and F7 SoCs family (except STM32F429), PLLSAI
output P can be used as 48MHz clock source for USB and SDMMC.
Signed-off-by: Patrice Chotard <[email protected]>
Tested By: Bruno Herrera <[email protected]>
|
|
To avoid board specificy LED activation code, automatically
activate gpio-leds with "default-state" property during bind().
Signed-off-by: Patrick Bruenn <[email protected]>
|
|
Add support for the device tree property "default-state". This feature
might be useful for LEDs indicating "power on" or similar states.
Note: Even with this commit gpio-leds remain in reset state. That's
because the led_gpio is not probed until DM_FLAG_ACTIVATED is set.
Signed-off-by: Patrick Bruenn <[email protected]>
|
|
Use live tree compatible api for pwm regulator.
Signed-off-by: Andy Yan <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
On a socfpga_cyclone5 based board the SD card, was never powered up. For
other dw_mmc based SoCs dwmci_probe() is called in the platform specific
probe(). It seems this call is missing for socfpga_dw_mmc.
With this change DWMCI_PWREN is set by dmwci_init().
Signed-off-by: Patrick Bruenn <[email protected]>
Reviewed-by: Jaehoon Chung <[email protected]>
|
|
Add the MMC_TRACE config in Kconfig.
Signed-off-by: Jaehoon Chung <[email protected]>
|
|
Add the debug message for checking the mmc clock status.
It's helpful to debug the controlling clock.
Signed-off-by: Jaehoon Chung <[email protected]>
|
|
mmc_set_clock() function has the disable argument as bool type.
When mmc_set_clock is called, it might be passed to "true" or "false".
But it's too confusion whether clock is enabled or disabled with only
"true" and "false".
To prevent the confusion, replace to MMC_CLK_ENABLE/DISABLE macro from
true/false.
Signed-off-by: Jaehoon Chung <[email protected]>
|
|
max77686 pmic is supporting with max77686.c under pmic/ and regulator/
direnctroy. Remove pmic_max77686.c what didn't use anywhere.
Instead, enable CONFIG_DM_REGULATOR_MAX77686 and
CONFIG_DM_PMIC_MAX77686.
Signed-off-by: Jaehoon Chung <[email protected]>
|
|
These are necessary to optimize the drive-strength of the pins.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
This allows our DT to specify drive-strength property.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Currently, the UniPhier pinctrl drivers expose only the pin-group
interface to device tree.
Provide .get_pins_count, .get_pin_name, .pinconf_set hooks to support
pin configuration via 'pins' DT property.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
The #include <linux/bug.h> is here to use BUILD_BUG_ON_ZERO().
By replacing it with <linux/build_bug.h>, we can reduce the number of
headers pulled in.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
dev_err() is more suitable for printing error messages.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Since commit f73cfb4d0dee ("pinctrl: uniphier: simplify input enable
and delete pin arrays"), these data are no longer used in any useful
way. Remove.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Currently CPU_V7 kconfig symbol supports only ARMv7A architectures under
armv7 folder. This led to a misconception of creating separate folders
for armv7m and armv7r. There is no reason to create separate folder for
other armv7 based architectures when it can co-exist with few Kconfig
symbols.
As a first step towards a common folder, rename CPU_V7 as CPUV7A. Later
separate Kconfig symbols can be added for CPU_V7R and CPU_V7M and
can co exist in the same folder.
Reviewed-by: Tom Rini <[email protected]>
Tested-by: Michal Simek <[email protected]>
Suggested-by: Alexander Graf <[email protected]>
Signed-off-by: Lokesh Vutla <[email protected]>
|
|
The syscon implementation in U-Boot is different from that in Linux.
Thus, DT files imported from Linux do not work for U-Boot.
In U-Boot driver model, each node is bound to a dedicated driver
that is the most compatible to it. This design gets along with the
concept of DT, and the syscon in Linux originally worked like that.
However, Linux commit bdb0066df96e ("mfd: syscon: Decouple syscon
interface from platform devices") changed the behavior because it is
useful to let a device bind to another driver, but still work as a
syscon provider.
That change had happened before U-Boot initially supported the syscon
driver by commit 6f98b7504f70 ("dm: Add support for generic system
controllers (syscon)"). So, the U-Boot's syscon works differently
from the beginning. I'd say this is mis-implementation given that
DT is not oriented to a particular project, but Linux is the canon
of DT in practice.
The problem typically arises in the combination of "syscon" and
"simple-mfd" compatibles.
In Linux, they are orthogonal, i.e., the order between "syscon" and
"simple-mfd" does not matter at all.
Assume the following compatible.
compatible = "foo,bar-syscon", "syscon", "simple-mfd";
In U-Boot, this device node is bound to the syscon driver
(driver/core/syscon-uclass.c) since the "syscon" is found to be the
most compatible. Then, syscon_get_regmap() succeeds.
However,
compatible = "foo,bar-syscon", "simple-mfd", "syscon";
does not work because this node is bound to the simple-bus driver
(drivers/core/simple-bus.c) in favor of "simple-mfd" compatible.
The compatible string "syscon" is just dismissed.
Moreover,
compatible = "foo,bar-syscon", "syscon";
works like the first case because the syscon driver populates the
child devices. This is wrong because populating children is the job
of "simple-mfd" (or "simple-bus").
This commit ports syscon_node_to_regmap() from Linux. This API
does not require the given node to be bound to a driver in any way.
Reported-by: Kunihiko Hayashi <[email protected]>
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Currently, regmap_init_mem() takes a udevice. This requires the node
has already been associated with a device. It prevents syscon/regmap
from behaving like those in Linux.
Change the first argumenet to take a device node.
Signed-off-by: Masahiro Yamada <[email protected]>
Acked-by: Neil Armstrong <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
device_is_compatible() takes udevice, but there is no such a helper
that takes ofnode.
Signed-off-by: Masahiro Yamada <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Putting zero length array at the end of struct is a common technique
to embed arbitrary length of members. There is no good reason to let
regmap_alloc_count() branch by "if (count <= 1)".
As far as I understood the code, regmap->base is an alias of
regmap->ranges[0].start, but it is not helpful but make the code
just ugly.
Rename regmap_alloc_count() to regmap_alloc() because the _count
suffix seems pointless.
Signed-off-by: Masahiro Yamada <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
[trini: fixup cpu_info-rcar.c]
Signed-off-by: Tom Rini <[email protected]>
|
|
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have multiple licenses (in
these cases, dual license) declared in the SPDX-License-Identifier tag.
In this case we change from listing "LICENSE-A LICENSE-B" or "LICENSE-A
or LICENSE-B" or "(LICENSE-A OR LICENSE-B)" to "LICENSE-A OR LICENSE-B"
as per the Linux Kernel style document. Note that parenthesis are
allowed so when they were used before we continue to use them.
Reviewed-by: Fabio Estevam <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <[email protected]>
|
|
|
|
|
|
The R8A7792 does not have the USB extal, so drop it.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Nobuhiro Iwamatsu <[email protected]>
|
|
As ret is not set when calling max77693_get_vcell() there is no
need to check ret again.
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
The 'SDHCI_QUIRK_NO_HISPD_BIT' is used wrong here. The purpose of this
quirk is to tell the sdhci-driver that the IP-core doesn't have a "high-
speed-enable" bit in its registers.
With this commit we change this to the correct quirk:
SDHCI_QUIRK_BROKEN_HISPD_MODE
Signed-off-by: Hannes Schmelzer <[email protected]>
|
|
Some IP-core implementations of the SDHCI have different troubles on the
silicon where they are placed.
On ZYNQ platform for example Xilinx doesn't accept the hold timing of an
eMMC chip which operates in High-Speed mode and must be forced to
operate in non high-speed mode. To get rid of this
"SDHCI_QUIRK_BROKEN_HISPD_MODE" is introduced.
For more details about this refer to the Xilinx answer-recor #59999
https://www.xilinx.com/support/answers/59999.html
This commit:
- doesn't set HISPD bit on the host-conroller
- reflects this fact within the host-controller capabilities
Upon this the layer above (mmc-driver) can setup the card correctly.
Otherwise the MMC card will be switched into high-speed mode and causes
possible timing violation on the host-controller side.
Signed-off-by: Hannes Schmelzer <[email protected]>
Signed-off-by: Hannes Schmelzer <[email protected]>
|
|
sd_read_ssr returns 0, means no error.
Fixes: 5b2e72f32721484("mmc: read ssr only if MMC write support is enabled")
Signed-off-by: Peng Fan <[email protected]>
Cc: Jaehoon Chung <[email protected]>
Cc: Jean-Jacques Hiblot <[email protected]>
|
|
An unsigned int is always >= 0.
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
