| Age | Commit message (Collapse) | Author |
|---|
|
Put all slave CPUs (CPU1-3) into WFI mode. Master CPU (CPU0) writes
the magic word into system manager's scratch register to indicate
the system has performed L2 reset and request reset manager to
perform hardware handshake and then trigger L2 reset. CPU0 put
itself into WFI mode. L2 reset will reboot all HPS CPU cores after
which all HPS cores are in WFI mode. L2 reset is followed by warm
reset request by SPL via RMR_EL3 system register.
Signed-off-by: Alif Zakuan Yuslaimi <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
The DDR data rate must be set correctly in the DDRIOCTRL
register according to the Actual Clock Frequency (ACF) value.
By enabling the reading of ACF value from bit 18 of the boot
scratch register during initialization, the DDR data rate is
able to be configured accurately.
Signed-off-by: Alif Zakuan Yuslaimi <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
Remove redundant code for MPFE CSR firewall disabled as this was
already set in DTreg dts.
Signed-off-by: Tien Fong Chee <[email protected]>
Signed-off-by: Alif Zakuan Yuslaimi <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
Setting up firewall regions based on SDRAM memory banks configuration
(up to CONFIG_NR_DRAM_BANKS banks) instead of using whole address space.
First 1 MiB (0 to 0xfffff) of SDRAM is configured as secure region,
other address spaces are non-secure regions. The ARM Trusted Firmware (ATF)
image is located in this first 1 MiB memory region. So, this can prevent
software executing at non-secure state EL0-EL2 and non-secure masters
access to secure region.
Add common function for firewall setup and reuse for all SoC64 devices.
Signed-off-by: Alif Zakuan Yuslaimi <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
Replace cm_wait_for_fsm() function with wait_for_bit_le32() function
which supports accurate timeout.
Signed-off-by: Alif Zakuan Yuslaimi <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
Enable watchdog as early as possible after clock initialization
which is set at 10 seconds.
Signed-off-by: Alif Zakuan Yuslaimi <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
Update the ARMv8 generic timer frequency register (cntfrq_el0)
with the actual hardware timer frequency (COUNTER_FREQUENCY_REAL).
The generic timer frequency was set to 0x200000000 during boot clk
which needs to be set to 0x400000000 when transition from boot clk
to PLL clk.
This will ensure that subsequent timer operations are based on the
correct frequency, ensuring accurate timekeeping.
Signed-off-by: Alif Zakuan Yuslaimi <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
In dwxgmac_of_get_mac_mode there is a test for mac_mode which will
return if false. After this point mac_mode is guaranteed to be true so
there is no need to test for this. Remove that test.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
In xgmac_probe there is a direct return after the point where unwind
gotos start to be used to undo actions performed by earlier code. Use
the appropriate unwind goto instead.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
Various fixes for smatch warnings, the i2c one might be also coming in
via Heiko / I2C tree, let me know if there is conflict.
There is also W77Q51NW SPI NOR ID support, with the DT portion omitted
for now.
|
|
In rswitch_probe the error detection after the call to devm_clk_get is
very wrong. It checks the value of ret which is uninitialised at that
point. Instead it should be using the macros for including errors into
pointers.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
Add IDs for Winbond W77Q51NW, 512M-bit Secure Serial Flash Memory
with Post-Quantum Cryptography, Dual/Quad SPI, QPI and DTR . The
flash part is similar to W25Q512NWM .
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Tudor Ambarus <[email protected]>
|
|
In rcar_iic_xfer if nmsgs == 0 the ret will not be assigned to. As ret
will always be 0 if the for loop is entered, may as well just return 0.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <[email protected]>
Reviewed-by: Heiko Schocher <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
In rcar_clk_set_rate64_div_table the unsigned variable 'value' is used
to receive the return value from rcar_clk_get_table_val which returns an
int and then attempts to test for being less than 0, which can never be
true. Instead declare value as an int so the code can behave as
expected. Also remove initial values from 'value' and 'div' as they are
not needed.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
Add i3c command file to support select, get i3c device
target list, read and write operation.
Signed-off-by: Dinesh Maniyam <[email protected]>
|
|
Fix the I3C device with spike filter unable to detect issue by setting
tHIGH_INIT to 200ns for first broadcast address.
This is according to MIPI SPEC 1.1.1 for first broadcast address
which is already part of linux upstreamed patch.
Signed-off-by: Dinesh Maniyam <[email protected]>
|
|
Picked linux i3c driver upstraming patch to fix the issue to
probe for i3c controller without slave device attached.
With this fix, the ret check will be on command error and will success
without slave device attached.
Signed-off-by: Dinesh Maniyam <[email protected]>
|
|
Add s simple test for the I3C uclass in sandbox.
Signed-off-by: Dinesh Maniyam <[email protected]>
|
|
Enable the Kconfig and Makefile for the MIPI DWI3C driver.
hs: fixed typo on drivers/i3c/master/Kconfig
Signed-off-by: Dinesh Maniyam <[email protected]>
|
|
Add new i3c driver to U-Boot drivers.
Signed-off-by: Dinesh Maniyam <[email protected]>
|
|
Enable i3c general uclass driver. This uclass driver will have
genaral read and write api to call the specific i3c driver.
Signed-off-by: Dinesh Maniyam <[email protected]>
|
|
Enable driver for Synopsis MIPI DWI3C for the family
device agilex5. This driver is migrated from linux version 6.6.37 LTS
Signed-off-by: Dinesh Maniyam <[email protected]>
|
|
In rcar_iic_xfer if nmsgs == 0 the ret will not be assigned to. As ret
will always be 0 if the for loop is entered, may as well just return 0.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <[email protected]>
Reviewed-by: Heiko Schocher <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-nand-flash
CI: https://source.denx.de/u-boot/custodians/u-boot-nand-flash/-/pipelines/27258
This series address issues found by Andrew Goodbody and mostly drop
driver that are not used by any board
|
|
- Pegatron Chagall, Samsung Galaxy R (GT-I9103) and Captivate Glide
(SGH-i927) support
|
|
As no platforms use this driver anymore let's go ahead and remove it.
Signed-off-by: Tom Rini <[email protected]>
|
|
As no platforms use this driver anymore let's go ahead and remove it.
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Michael Trimarchi <[email protected]>
|
|
As no platforms use this driver anymore let's go ahead and remove it.
Signed-off-by: Tom Rini <[email protected]>
|
|
In mxs_nand_init_ctrl there are a couple of error paths that do not set
err which could lead to the errors being silently ignored despite the
function not completing. Rather than just using if to detect these
errors use err to collect the error return value from the called
functions.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <[email protected]>
Reviewed-by: Michael Trimarchi <[email protected]>
|
|
In denali_wait_for_irq the code will either return from inside the while
loop or exit with time_left being 0. The following test for time_left
being 0 is guranteed to be true so remove the test and the following
unreachable code.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <[email protected]>
Reviewed-by: Michael Trimarchi <[email protected]>
|
|
In init_nand_dma there was code to detect failure to allocate memory but
it had two problems. Firstly the 2nd clause when info->tx_desc was NULL
attempted to free info->tx_desc when it should be freeing info->rx_desc.
Secondly there was no detection of both allocations failing, arguably
the more likely scenario. Refactor the code to simplify it and just fail
as soon as either allocation fails.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <[email protected]>
Reviewed-by: Michael Trimarchi <[email protected]>
|
|
Add kfree calls on error paths for memory that was allocated. This will
prevent memory leaks.
This issue found by Smatch.
Signed-off-by: Andrew Goodbody <[email protected]>
Reviewed-By: Michael Trimarchi <[email protected]>
|
|
In stm32_fmc2_nfc_probe there are 3 error returns that do not set the
error code before returning which could lead to the error being silently
ignored. Just return -EINVAL in each case.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
|
In pxa3xx_nand_probe_dt if the function detects an error after
allocating memory that memory is not freed before exit. Add the
appropriate free.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <[email protected]>
Reviewed-by: MIchael Trimarchi <[email protected]>
|
|
The Auto Negotiation procedure between two Ethernet PHYs consists of
determining the best commonly supported parameters among Speed,
Duplex Mode and Flow Control.
The time taken for this procedure is not only dependent on the local
PHY used, but also on the link-partner PHY.
While a timeout can be specified in the form of a "CONFIG" on the basis
of the local PHY present on the device, since the timeout also depends
on the link-partner PHY, it might be necessary to modify the timeout.
To avoid rebuilding the bootloader for a given device, just because it
may be connected to various link-partner PHYs, each with a different
timeout, introduce an environment variable named "phy_aneg_timeout" and
override "CONFIG_PHY_ANEG_TIMEOUT" with "phy_aneg_timeout".
Signed-off-by: Siddharth Vadapalli <[email protected]>
Acked-by: Jerome Forissier <[email protected]>
[jf: add missing #include <env.h>]
Signed-off-by: Jerome Forissier <[email protected]>
|
|
Every virtqueue_add must eventually be followed by virtqueue_kick for to
properly notify the peer that new buffers have been put into the queue.
This is currently missing for virtio-net and may result in non-working
network when the host has depleted the rx buffers and waits for new
buffers. Depending on the host it may busy poll on the virtio queue or
wait for the kick. Qemu does the latter and may break.
Signed-off-by: Christian Speich <[email protected]>
|
|
As no platforms enable the ethernet driver, remove it.
Signed-off-by: Tom Rini <[email protected]>
|
|
A large number of network drivers cannot build without access to some
platform specific header files. Express those requirements in Kconfig as
well. This covers the QUICC engine drivers as that is networking
driver infrastructure.
Signed-off-by: Tom Rini <[email protected]>
|
|
The common portable header for CPU related functions such as cache
flushing and invalidation is <cpu_func.h> so add that to these drivers.
Signed-off-by: Tom Rini <[email protected]>
|
|
In the debug print in ftgmac100_send we want to say where the packet is
in memory and what the length is, so use %p to print that.
Signed-off-by: Tom Rini <[email protected]>
|
|
Add support for PWM backlight found in Samsung CMC623 image converter.
Signed-off-by: Ion Agorria <[email protected]>
Reviewed-by: Svyatoslav Ryhel <[email protected]>
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
Add support for a Samsung CMC623 image converter chip found in several
Samsung devices such as Samsung Galaxy R (I9103) and Samsung Galaxy
Tab 10.1 (GT-P75xx).
Signed-off-by: Ion Agorria <[email protected]>
Reviewed-by: Svyatoslav Ryhel <[email protected]>
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
Samsung S6E63M0 controller is found in some OLED panels like one used in
the Samsung Captivate Glide. Currently only DBI C panel is implemented.
Signed-off-by: Ion Agorria <[email protected]>
Reviewed-by: Svyatoslav Ryhel <[email protected]>
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
Sony L4F00430T01 LCD module is found in Samsung Galaxy R. The panel has a
WVGA resolution (480x800) and is setup over SPI, video data comes from RGB.
Signed-off-by: Ion Agorria <[email protected]>
Reviewed-by: Svyatoslav Ryhel <[email protected]>
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
Configure pixel clock and data enable polarity according to panel flags.
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
This driver allows using Tegra AES engines within BSEV and BSEA blocks to
encrypt and decrypt data using different AES algorithms.
One use case is allowing u-boot to self update by using the already loaded
AES key in the engine's SBK slot by the bootrom.
Particular care must be taken as chainloaded u-boot's may not have the SBK
slot loaded as the vendor bootloader erases it before leaving it.
Signed-off-by: Ion Agorria <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-stm
CI: https://source.denx.de/u-boot/custodians/u-boot-stm/-/pipelines/27236
- Add support for STM32 TIMERS and STM32 PWM on STM32MP25
- Add STM32MP13xx SPL and OpTee-OS start support
- Fix header misuse in stm32 reset drivers
- Fix STMicroelectronics spelling
- Fix clk-stm32h7 wrong macros used in register read
- Fix PRE_CON_BUF_ADDR on STM32MP13
- Fix clock identifier passed to struct scmi_clk_parent_set_in
- Fix stm32 reset for STM32F4/F7 and H7
- Enable OF_UPSTREAM_BUILD_VENDOR for stm32mp13_defconfig
- Add STM32MP23 SoC and stm32mp235f-dk board support
|
|
https://source.denx.de/u-boot/custodians/u-boot-socfpga
This pull request includes updates for the SoCFPGA platform intended for the 2025.10 release
cycle. The highlights focus on enabling the Power Manager for Agilex5, NAND boot support
enhancements, and various bug fixes and cleanups across SoCFPGA components.
CI:
* https://source.denx.de/u-boot/custodians/u-boot-socfpga/-/pipelines/27221
Summary of changes:
Agilex5 Power Manager:
* Initial driver support and DT bindings are added for the Agilex5 Power Manager, enabling
better power domain control.
NAND Boot Support for Agilex5:
* SPL support for NAND boot is enabled.
* UBI/UBIFS support is configured in defconfigs.
* Memory layout updates (malloc and BSS relocation) ensure proper boot behavior.
Code Quality Improvements:
* Coverity and runtime bug fixes (e.g., jtag_usercode check, sub-device conditionals).
* Several cleanup patches addressing formatting, logic, and initialization issues.
General Maintenance:
* SPDX license tags and header include fixes.
* Device tree updates to limit SPI clock frequency and other minor adjustments.
These contributions come from Alif Zakuan Yuslaimi, Andrew Goodbody, Dinesh Maniyam, Naresh
Kumar Ravulapalli, and Tingting Meng.
This patch set has been tested on Agilex 5 devkit.
|
|
family"
Lukasz Czechowski <[email protected]> says:
This patch series extends the usb_onboard_hub driver to allow for
support of more types of onboard hub devices, and adds the Cypress HX3
hub family.
First patch in the series updates the bind function, so that it no
longer uses hardcoded compatible strings.
Next patch simplifies the code, by removing unnecessary dm_gpio function
call.
Third patch updates the remove function, which allows the prevent issues
with usb devices reenumeration, in case of calling "usb reset". Although
the issue could still occur in case of invalid initial state of reset
gpio, it is minimized with no impact on main usb_hub driver.
Fourth patch extends the driver with support for multiple power
supplies, the same way it is done in kernel driver. Finally, last patch
provides hub data and of_match table entries for Cypress HX3
Link: https://lore.kernel.org/r/20250722-usb_onboard_hub_cypress_hx3-v4-0-91c3ee958c0e@thaumatec.com
|
|
The reset GPIO is obtained during driver probing by the function
devm_gpiod_get_optional, which means the GPIO will be automatically
freed when the device is removed. Because of this, explicit call
to free the reset GPIO in hub remove function is not needed.
To support the Managed device resources, the DEVRES config must
be enabled, otherwise the devres functions fall back to non-managed
variants. Set the necessary dependency to DEVRES in Kconfig.
Reviewed-by: Quentin Schulz <[email protected]>
Signed-off-by: Lukasz Czechowski <[email protected]>
|
