| Age | Commit message (Collapse) | Author |
|---|
|
There is code that is specifically for RGMII_TXID interface, but this
will never get used because the code checks that the RGMII interface
is RGMII_ID to RGMII_RXID; RGMII_TXID is after this.
To fix this and avoid similar problems in the future, use the
phy_interface_is_rgmii helper function.
Signed-off-by: Phil Edworthy <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Remove the redundant #ifdef CONFIG_DM_ETH/#endif.
Signed-off-by: Wenyou Yang <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Due to introducing the at91 clock driver, add the clock support.
Signed-off-by: Wenyou Yang <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Add CONFIG_MACB option in KConfig to be used to select the Cadence
MACB Ethernet driver.
Signed-off-by: Wenyou Yang <[email protected]>
|
|
This is not supported, so disable it for now.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
Fix a few types that causes warnings on 64-bit machines.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
Some files are missing this declaration. Add it to avoid build errors when
we actually need the declaration.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
We should use unsigned long rather than u32 for addresses. Update this so
that the table-generation code builds correctly on 64-bit machines.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
Add an option for building Platorm Controller Hub drivers in SPL.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
Add a new Kconfig option to allow timer drivers to be used in SPL.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
Add a new Kconfig option to allow RTC drivers to be used in SPL.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
Add a new Kconfig option to allow PCI drivers to be used in SPL.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
Add a new Kconfig option to allow CPU drivers to be used in SPL.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
Signed-off-by: Tom Rini <[email protected]>
Conflicts:
configs/ls1046aqds_defconfig
configs/ls1046aqds_nand_defconfig
configs/ls1046aqds_qspi_defconfig
configs/ls1046aqds_sdcard_ifc_defconfig
configs/ls1046aqds_sdcard_qspi_defconfig
configs/ls1046ardb_emmc_defconfig
configs/ls1046ardb_qspi_defconfig
configs/ls1046ardb_sdcard_defconfig
|
|
Signed-off-by: Robert P. J. Day <[email protected]>
|
|
|
|
This patch adds a function to the TPM library, which allows U-Boot to
flush resources, e.g. keys, from the TPM.
Signed-off-by: Mario Six <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Add support for Marvell 88E1680 Integrated Octal
10/100/1000 Mbps Energy Efficient Ethernet Transceiver.
Signed-off-by: Dirk Eibach <[email protected]>
Signed-off-by: Mario Six <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Armada 38x has four PCI ports, not three.
The optimization in pci_init_board() seems to assume that every port has
three lanes. This is obviously wrong, and breaks support for Armada 38x.
Signed-off-by: Dirk Eibach <[email protected]>
Signed-off-by: Mario Six <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Now that the SD/SDIO/MMC DT properties are updated in the Marvell
A3700 and A7/8k DT files, we need to match the checks for compatible
node in the PHY driver as well.
Signed-off-by: Stefan Roese <[email protected]>
Cc: Kostya Porotchkin <[email protected]>
Cc: Nadav Haklai <[email protected]>
Reviewed-by: Jaehoon Chung <[email protected]>
|
|
Fixup port_mac_address property in MC DPC with values from the u-boot
environment. Since u-boot already reads the environment MAC addresses
when probing the PHYs, use these values.
The u-boot environment MAC addresses take precedence over any eventual
ones defined in the DPC, except for the case where they are randomly
assigned (no u-boot env value declared for port).
The patch assumes the "/board_info/ports/" node is present in the DPC.
Signed-off-by: Bogdan Purcareata <[email protected]>
Reviewed-by: Prabhakar Kushwaha <[email protected]>
[York S: Fix several indentations]
Reviewed-by: York Sun <[email protected]>
|
|
Make the naming scheme consistent; all SDHCI-base drivers prefixed
with CONFIG_MMC_SDHCI_.
While we are here, add "depends on ARCH_AT91".
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Make the naming scheme consistent; all SDHCI-base drivers prefixed
with CONFIG_MMC_SDHCI_.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Make the naming scheme consistent; all SDHCI-base drivers prefixed
with CONFIG_MMC_SDHCI_.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Make the naming scheme consistent; all SDHCI-base drivers prefixed
with CONFIG_MMC_SDHCI_.
While we are here, add "depends on ARCH_ROCKCHIP".
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Make the naming scheme consistent; all SDHCI-base drivers prefixed
with CONFIG_MMC_SDHCI_.
While we are here, add "depends on ARCH_ZYNQ || ARCH_ZYNQMP".
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
[1] Rename CONFIG_SANDBOX_MMC to CONFIG_MMC_SANDBOX for consistency
I want all MMC driver options prefixed with CONFIG_MMC_.
[2] Fix dependency
Add necessary depends on to avoid compile error.
Instead "depends on MMC" is unneeded because this config entry
resides inside of "if MMC".
[3] Currently, this config symbol is not referenced at all.
Use it to enable/disable the driver in Makefile.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Now, CONFIG_GENERIC_MMC seems equivalent to CONFIG_MMC.
Let's create an entry for "config GENERIC_MMC" with "default MMC",
then convert all macro defines in headers to Kconfig. Almost all
of the defines will go away.
I see only two exceptions:
configs/blanche_defconfig
configs/sandbox_noblk_defconfig
They define CONFIG_GENERIC_MMC, but not CONFIG_MMC. Something
might be wrong with these two boards, so should be checked later.
Anyway, this is the output of the moveconfig tool.
This commit was created as follows:
[1] create a config entry in drivers/mmc/Kconfig
[2] tools/moveconfig.py -r HEAD GENERIC_MMC
[3] manual clean-up of garbage comments in doc/README.* and
include/configs/*.h
Signed-off-by: Masahiro Yamada <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
The readl_poll_timeout() is a useful helper to poll registers
and error out if the condition is not met.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
This include is unnecessary for low-level drivers.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
I missed to update them when DT files were resynced with Linux.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
This patch adds support for the QSPI IP found in stm32f7 devices.
Signed-off-by: Michael Kurz <[email protected]>
|
|
This patch adds support for SMSC LAN8742 in phylib
Signed-off-by: Michael Kurz <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
This patch adds glue code required for enabling the designware
mac on stm32f7 devices.
Signed-off-by: Michael Kurz <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
Clock Driver
This driver is ast2500-specific and is not compatible with earlier
versions of this chip. The differences are not that big, but they are
in somewhat random places, so making it compatible with ast2400 is not
worth the effort at the moment.
SDRAM MC driver
The driver is very ast2500-specific and is completely incompatible
with previous versions of the chip.
The memory controller is very poorly documented by Aspeed in the
datasheet, with any mention of the whole range of registers missing. The
initialization procedure has been basically taken from Aspeed SDK, where
it is implemented in assembly. Here it is rewritten in C, with very limited
understanding of what exactly it is doing.
Reviewed-by: Simon Glass <[email protected]>
|
|
Add support for Watchdog Timer, which is compatible with AST2400 and
AST2500 watchdogs. There is no uclass for Watchdog yet, so the driver
does not follow the driver model. It also uses fixed clock, so no clock
driver is needed.
Add support for timer for Aspeed ast2400/ast2500 devices.
The driver actually controls several devices, but because all devices
share the same Control Register, it is somewhat difficult to completely
decouple them. Since only one timer is needed at the moment, this should
be OK. The timer uses fixed clock, so does not rely on a clock driver.
Add sysreset driver, which uses watchdog timer to do resets and particular
watchdog device to use is hardcoded (0)
Reviewed-by: Simon Glass <[email protected]>
|
|
|
|
|
|
This is not used in U-Boot. Drop this option and associated dead code.
Signed-off-by: Simon Glass <[email protected]>
|
|
This driver implementes platform specific code for the Xenon SDHCI
controller which is integrated in the Marvell MVEBU Armada 37xx and
Armada 7k / 8K SoCs.
History:
This driver is ported from the Marvell U-Boot version 2015.01 which is
written by Victor Gu <[email protected]> with minor changes ported from
the Linux driver which is written by Ziji Hu <[email protected]>.
Signed-off-by: Stefan Roese <[email protected]>
Cc: Jaehoon Chung <[email protected]>
Cc: Masahiro Yamada <[email protected]>
Reviewed-by: Jaehoon Chung <[email protected]>
|
|
Some SDHCI drivers might need to do some special controller configuration
after the common clock set_ios() function has been called (speed / width
configuration). This patch adds a call to the newly created function
set_ios_port() when its configured in the host driver.
This will be used by the Xenon SDHCI controller driver used on the
Marvell Armada 3700 and 7k/8k ARM64 SoCs.
Signed-off-by: Stefan Roese <[email protected]>
Cc: Jaehoon Chung <[email protected]>
Cc: Simon Glass <[email protected]>
Reviewed-by: Jaehoon Chung <[email protected]>
|
|
This patch completely clears the SDHCI_CLOCK_CONTROL register before the
new value is configured instead of just clearing the 2 bits
SDHCI_CLOCK_CARD_EN and SDHCI_CLOCK_INT_EN. Without this change, some
clock configurations will lead to the "Internal clock never stabilised."
error message on the Xenon SDHCI controller used on the Marvell Armada
3700 and 7k/8k ARM64 SoCs.
The Linux SDHCI core driver also writes 0 to this register before
the new value is configured. So this patch simplifies the driver a bit
and brings the U-Boot driver more in-line with the Linux one.
Signed-off-by: Stefan Roese <[email protected]>
Cc: Jaehoon Chung <[email protected]>
Cc: Siva Durga Prasad Paladugu <[email protected]>
Cc: Michal Simek <[email protected]>
Reviewed-by: Jaehoon Chung <[email protected]>
|
|
The read-only-write-enable bit is set by default and must be cleared
to prevent overwriting read-only registers. This should be done
immediately after resetting the PCI Express controller.
Reviewed-by: Hamish Martin <[email protected]>
Signed-off-by: Tony O'Brien <[email protected]>
[York S: Move SYS_FSL_ERRATUM_A007815 to Kconfig]
Reviewed-by: York Sun <[email protected]>
|
|
Print the error code for non-zero (failure case) instead
of making debug statement without any condition, this
usually gives proper clue in failure condition.
Log:
|
|
The sdhci controller assumes that the base clock frequency is fully supported by
the peripheral and doesn't support hardware limitations. The Linux kernel
distinguishes between base clock (max_clk) of the host controller and maximum
frequency (f_max) of the card interface. Use the same differentiation and allow
the platform to constrain the peripheral interface.
Signed-off-by: Stefan Herbrechtsmeier <[email protected]>
|
|
Add pin configuration and pinmux support for UniPhier PXs3 SoC.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Move all of the status LED feature to drivers/led/Kconfig.
The LED status definitions were moved from the board configuration
files to the defconfig files.
TBD: Move all of the definitions in the include/status_led.h to the
relevant board's defconfig files.
Tested boards: CL-SOM-AM57x, CM-T335
Signed-off-by: Uri Mashiach <[email protected]>
|
|
Move all of the status LED feature to drivers/led/Kconfig.
doc/README.LED updated to reflect the Kconfig implementation.
Tested boards: CL-SOM-AM57x, CM-T335
Signed-off-by: Uri Mashiach <[email protected]>
|
|
commit: 65f83802b7a5b "serial: 16550: Add getfcr accessor"
breaks u-boot commandline working with long commands
sending to the board.
Since the above patch, you have to setup the fcr register.
For board/archs which enable OF_PLATDATA, the new field
fcr in struct ns16550_platdata is not filled with a
default value ...
This leads in not setting up the uarts fifo, which ends
in problems, when you send long commands to u-boots
commandline.
Detected this issue with automated tbot tests on am335x
based shc board.
The error does not popup, if you type commands. You need
to copy&paste a long command to u-boots commandshell
(or send a long command with tbot)
Possible boards/plattforms with problems:
./arch/arm/cpu/arm926ejs/lpc32xx/devices.c
./arch/arm/mach-tegra/board.c
./board/overo/overo.c
./board/quipos/cairo/cairo.c
./board/logicpd/omap3som/omap3logic.c
./board/logicpd/zoom1/zoom1.c
./board/timll/devkit8000/devkit8000.c
./board/lg/sniper/sniper.c
./board/ti/beagle/beagle.c
./drivers/serial/serial_rockchip.c
Signed-off-by: Heiko Schocher <[email protected]>
Signed-off-by: Ladislav Michl <[email protected]>
Tested-by: Adam Ford <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
|
