| Age | Commit message (Collapse) | Author |
|---|
|
This is a port of the read data bus interface from the Linux
brcmnand driver, commit 546e425991205f59281e160a0d0daed47b7ca9b3
"mtd: rawnand: brcmnand: Add BCMBCA read data bus interface"
This is needed for the BCMBCA RAW NAND driver.
Signed-off-by: William Zhang <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
Reviewed-by: William Zhang <[email protected]>
|
|
Backport from upstream Linux
commit 60177390fa061c62d156f4a546e3efd90df3c183
"mtd: rawnand: brcmnand: Fix mtd oobsize"
brcmnand controller can only access the flash spare area up to certain
bytes based on the ECC level. It can be less than the actual flash spare
area size. For example, for many NAND chip supporting ECC BCH-8, it has
226 bytes spare area. But controller can only uses 218 bytes. So brcmand
driver overrides the mtd oobsize with the controller's accessible spare
area size. When the nand base driver utilizes the nand_device object, it
resets the oobsize back to the actual flash spare aprea size from
nand_memory_organization structure and controller may not able to access
all the oob area as mtd advises.
This change fixes the issue by overriding the oobsize in the
nand_memory_organization structure to the controller's accessible spare
area size.
Fixes: a7ab085d7c16 ("mtd: rawnand: Initialize the nand_device object")
Signed-off-by: William Zhang <[email protected]>
Signed-off-by: Miquel Raynal <[email protected]>
Link: https://lore.kernel.org/linux-mtd/[email protected]
Signed-off-by: Linus Walleij <[email protected]>
Reviewed-by: William Zhang <[email protected]>
|
|
Backport of upstream Linux
commit 5d53244186c9ac58cb88d76a0958ca55b83a15cd
"mtd: rawnand: brcmnand: Fix potential out-of-bounds access in oob write"
When the oob buffer length is not in multiple of words, the oob write
function does out-of-bounds read on the oob source buffer at the last
iteration. Fix that by always checking length limit on the oob buffer
read and fill with 0xff when reaching the end of the buffer to the oob
registers.
Signed-off-by: William Zhang <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: Miquel Raynal <[email protected]>
Link: https://lore.kernel.org/linux-mtd/[email protected]
Signed-off-by: Linus Walleij <[email protected]>
Reviewed-by: William Zhang <[email protected]>
|
|
Backport from the Linux kernel:
commit 9cc0a598b944816f2968baf2631757f22721b996
"mtd: rawnand: brcmnand: Fix potential false time out warning"
If system is busy during the command status polling function, the driver
may not get the chance to poll the status register till the end of time
out and return the premature status. Do a final check after time out
happens to ensure reading the correct status.
Signed-off-by: William Zhang <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: Miquel Raynal <[email protected]>
Link: https://lore.kernel.org/linux-mtd/[email protected]
Signed-off-by: Linus Walleij <[email protected]>
Reviewed-by: William Zhang <[email protected]>
|
|
Backport from the Linux kernel
commit 2ec2839a9062db8a592525a3fdabd42dcd9a3a9b
"mtd: rawnand: brcmnand: Fix ECC level field setting for v7.2 controller"
v7.2 controller has different ECC level field size and shift in the acc
control register than its predecessor and successor controller. It needs
to be set specifically.
Signed-off-by: William Zhang <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: Miquel Raynal <[email protected]>
Link: https://lore.kernel.org/linux-mtd/[email protected]
Signed-off-by: Linus Walleij <[email protected]>
Reviewed-by: William Zhang <[email protected]>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx into next
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/22526
- Add DA9063 watchdog support for the imx6q-lxr2 board.
- Add support for DH electronics i.MX8M Plus DHCOM PicoITX
- Add DH i.MX8MP DHCOM SoM on DRC02 carrier board
- Several fsl_esdhc_imx improvements.
- Pas no-mmc-hs400 to mmc2 on imx8mm-cl-iot-gate.
|
|
https://source.denx.de/u-boot/custodians/u-boot-snapdragon into next
* Initial UFS PHY driver
* Support for SM8150 (clock and pinctrl)
* Allow writing configuration to PMIC GPIOs again
* Support for configuring "special" pins (e.g. UFS reset or sdhc pins)
* Support for "clk dump" command to decode various clocks.
|
|
The series "rockchip: Add efuse and otp support to more SoCs" [1],
merged in v2023.04, refactored and extended the Rockchip efuse and otp
driver to support reading eFUSE/OTP for all supported Rockchip SoCs.
Due to use of different licenses the drivers were never combined into a
single driver, however anything non SoC specific should be applied to
both drivers.
The commit fe38b88453d2 ("rockchip: Provided SPL control over efuse
presence") changed Makefile options for only one of the two drivers,
apply same change to keep these two drivers in sync.
[1] https://lore.kernel.org/r/[email protected]/
Fixes: fe38b88453d2 ("rockchip: Provided SPL control over efuse presence")
Signed-off-by: Jonas Karlman <[email protected]>
|
|
Drop in the RCG and GPLL data for debugging these clocks.
Signed-off-by: Caleb Connolly <[email protected]>
|
|
Add "clk dump" support for SM6115.
Signed-off-by: Caleb Connolly <[email protected]>
|
|
Add debug data to dump PLL and RCG clocks.
Signed-off-by: Caleb Connolly <[email protected]>
|
|
Add support for dumping a few of the clocks used on Qualcomm platforms.
Naming the Global PLL's, Root Clock Generators, and gate clocks.
This helps a lot with platform bringup and feature enablement by making
it easy to sanity check that the clocks are programmed correctly.
== Usage ==
Enable CONFIG_CMD_CLK and "#define LOG_DEBUG" at the top of
qcom-<soc>.c.
The "clk dump" command should print the states of all the gates, GPLLs
and RCGs for your SoC.
== Glossary ==
RCG: Root Clock Generator
* Takes in some fairly arbitrary high freq clock (configurable clock
source and options for taking just even pulses and other things)
* Output frequency = input_freq * (m/n) * (1/d) where m/n are arbitrary
8 or 16-bit values (depending on the RCG), and d is a number (with
support for .5 offsets).
GPLL: Global Phase Locked Loop
* Crystal as input
* integer multiplier + exponent part (2^-40)
Gate: Simple on/off clock
* Put between RCGs and the peripherals they power
* Required to allow for correct power sequencing
If you do the maths manually using the equations from "clk dump", the
numbers should roughly line up by they're likely to be out by a handful
of MHz. They output is formatted so that it can be pasted directly into
the python interpreter.
Signed-off-by: Caleb Connolly <[email protected]>
|
|
This reverts commit 19f000b72b2fa7e4540f7cdb91287aff594239bd.
The bug in writing was caused by a long-standing error in the SPMI
driver which has since been fixed - c2de620d64d4 ("spmi: msm: fix
version 5 support"). We can safely enable writing GPIO configuration
now.
Reviewed-by: Neil Armstrong <[email protected]>
Signed-off-by: Caleb Connolly <[email protected]>
|
|
Add the special pins configuration data to allow setup the bias
of the UFS and SDCard pins on the SM8250 SoC.
Signed-off-by: Neil Armstrong <[email protected]>
Reviewed-by: Caleb Connolly <[email protected]>
|
|
Leverage the data introduced in the struct msm_special_pin_data to allow
setting the gpio direction and value if supported by the pin data.
Signed-off-by: Neil Armstrong <[email protected]>
Reviewed-by: Caleb Connolly <[email protected]>
|
|
Add Qualcomm QMP UFS PHY driver which is available on the following
Snapdragon SoCs - SDM845, SM8250, SM8550 and SM8650 SoCs.
Signed-off-by: Bhupesh Sharma <[email protected]>
Signed-off-by: Neil Armstrong <[email protected]>
|
|
Import Qualcomm QMP phy related header files from Linux v6.11-rc7,
limit to headers needed to setup QMP v2 to v6 UFS PHYs.
Signed-off-by: Bhupesh Sharma <[email protected]>
Signed-off-by: Neil Armstrong <[email protected]>
|
|
Add pinctrl and GPIO driver for SM8150. Driver code is based on the
similar U-Boot drivers. All constants are taken from the corresponding
Linux driver. This drivers differs from the similar U-Boot drivers,
because SM8150 SoC have different function IDs for the same functions
on different pins.
Co-authored-by: Volodymyr Babchuk <[email protected]>
Reviewed-by: Caleb Connolly <[email protected]>
Signed-off-by: Julius Lehmann <[email protected]>
Reviewed-by: Neil Armstrong <[email protected]>
|
|
Add clock, reset and power domain driver for SM8150. Driver code is
based on the similar U-Boot drivers. All constants are taken from the
corresponding Linux driver.
This driver supports clock rate setting only debug UART,
RGMII/Ethernet modules and USB controller.
Co-authored-by: Volodymyr Babchuk <[email protected]>
Reviewed-by: Caleb Connolly <[email protected]>
Signed-off-by: Julius Lehmann <[email protected]>
Reviewed-by: Neil Armstrong <[email protected]>
|
|
The DA9063 PMIC is a multi-function device that provides
regulator, watchdog, RTC, and ON key functionalities.
Add support for the DA9063 PMIC watchdog functionality.
Based on the 6.11 kernel drivers/watchdog/da9063_wdt.c driver.
Signed-off-by: Fabio Estevam <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
When supporting partition reset for SoC such as i.MX95 , the Linux
Kernel may have configured the tuning, while after force reset by
wdog or else, uboot CMD0 will never pass unless config RSTT to reset
tuning logic.
Since RSTA and RSTT are independent, so need both to be reseted in the
controller.
Acked-by: Haibo Chen <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
|
|
The memory of priv and plat are leaked if max_bus_width is wrong.
Signed-off-by: Ye Li <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
|
|
The plat->cfg is wrongly memset to 0, so the host_caps value configured
in fsl_esdhc_initialize is reset. Remove the unnecessary memset since
plat is allocated via calloc.
Reviewed-by: Peng Fan <[email protected]>
Signed-off-by: Ye Li <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
|
|
According to SD and MMC spec, 74 clocks must be sent to device after
power stable. This is need in reinit ops for DM MMC or init ops for
non-DM MMC after power cycle.
So set the INTIA to send 80 clocks in esdhc_init_common and move
its calling from probe to reinit.
However, on 8MQ EVK and 8QXP MEK with some brands of SD cards, sending
80 clocks may not work well.
The root cause is related with power up time. According to spec, after
power stable, host shall supply at least 74 SD clocks to the SD card with
the maximum of 1ms. However, the power ram up time is related with the
characteristic of SD card. At the moment of sending 74 SD clocks, the
power probably not ram up to the operating level on the problematic
cards. Then cause the cards not ready.
This patch changes to send SD clock with 1ms duration to replace 80
SD clocks (0.2ms at 400Khz clock).
This way meets the spec requirement as well, and adds the margin for
power ram up time to be compatible with the problematic SD cards.
This is also aligned with implementation which has FORCE clock
always on.
Reviewed-and-tested-by: Haibo Chen <[email protected]>
Signed-off-by: Ye Li <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
|
|
With partition reset supported for i.MX8QM/QXP/95 and etc, when linux
mmc runtime suspended, the mmc clks are gated off. While at same time
system controller reset Cortex-A cores because of various reasons(
WDOG timeout and etc), with SPL run again, only enable PER clk is not
enough, also need to enable AHB/IPG clk, here use clk bulk API to enable
all the clocks.
Signed-off-by: Peng Fan <[email protected]>
|
|
So we can disable to build ADP5585 in SPL to save size
Signed-off-by: Ye Li <[email protected]>
Signed-off-by: Alice Guo <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-dfu into next
u-boot-dfu-next-20241003
CI: https://source.denx.de/u-boot/custodians/u-boot-dfu/-/pipelines/22516
DFU:
- Reinitialize only if dfu_alt_info changed
USB Gadget:
- New usb gadget driver for Renesas USBHS
- Simplify kconfig deps for CMD_USB_MASS_STORAGE
Android:
- Provide bootloader version to android via kernel commandline
|
|
Simon Glass <[email protected]> says:
This includes various patches towards implementing the VBE abrec
bootmeth in U-Boot.
|
|
This driver should not generally be present in SPL, even if misc devices
are enabled. Update the Makefile rule accordingly.
Signed-off-by: Simon Glass <[email protected]>
|
|
Add a missing colon and newline in rk3399_emmc_get_phy().
Signed-off-by: Simon Glass <[email protected]>
|
|
Allow MMC init when clock support is not enabled in a particular phase.
Refactor the setting of priv->emmc_clk so it is a bit clearer.
Signed-off-by: Simon Glass <[email protected]>
|
|
Add a little logging to some places in this driver, to aid debugging
when something goes wrong.
Signed-off-by: Simon Glass <[email protected]>
|
|
Add an error-return log to the call in mmc_init_device()
Signed-off-by: Simon Glass <[email protected]>
|
|
Some boards want to use DM_MMC in TPL so add an option for that.
Signed-off-by: Simon Glass <[email protected]>
|
|
Some boards want to use the debug UART in TPL so add an option for that.
Signed-off-by: Simon Glass <[email protected]>
|
|
Some boards want to use RAM in VPL so add an option for that.
Signed-off-by: Simon Glass <[email protected]>
|
|
Add an option so that this feature can be enabled in TPL for boards
which need it.
Signed-off-by: Simon Glass <[email protected]>
|
|
This commit adds support to manage an external regulator to enable the main
power supply VDD.
Signed-off-by: Arturo Buzarra <[email protected]>
|
|
A write to the TX buffer is performed before entering the loop to "avoid
clock starvation". This sometimes results in subsequent writes in
davinci_spi_xfer_data() to occur while the TXFULL bit is asserted,
leading to write failures.
Remove the preload of the TX buffer.
Signed-off-by: Bastien Curutchet <[email protected]>
|
|
When SPL_FS_LOADER is set to y and FS_LOADER is not enabled, the SPL build
fails with the following errors:
AR spl/boot/built-in.o
LD spl/u-boot-spl
arm-none-linux-gnueabihf-ld.bfd: drivers/misc/fs_loader.o: in function
`fw_get_filesystem_firmware':
/u-boot/drivers/misc/fs_loader.c:162: undefined reference to
`fs_set_blk_dev'
arm-none-linux-gnueabihf-ld.bfd: /home/frh/tdx/src/u-boot/drivers/misc/
fs_loader.c:185: undefined reference to `fs_read'
arm-none-linux-gnueabihf-ld.bfd: drivers/misc/fs_loader.o: in function
`select_fs_dev':
/u-boot/drivers/misc/fs_loader.c:89: undefined reference to
`fs_set_blk_dev_with_part'
make[1]: *** [scripts/Makefile.spl:527: spl/u-boot-spl] Error 1
make: *** [Makefile:2055: spl/u-boot-spl] Error 2
Fix it by replacing the FS_LOADER with SPL_FS_LOADER in the Makefile, so
the fs.c with the necessary function definitions are compiled.
Fixes: b071a07743d4 ("drivers: misc: Makefile: Enable fs_loader compilation at SPL Level")
Suggested-by: Francesco Dolcini <[email protected]>
Signed-off-by: Hiago De Franco <[email protected]>
Signed-off-by: Francesco Dolcini <[email protected]>
|
|
Add UDC driver for Renesas USBHS controller found in R-Car Gen3 SoCs.
This is mostly ported from the Linux kernel, with additional porting
glue. The code has been synchronized with 1b4861e32e46 ("Linux 6.9.3")
and cleaned up and ported to DM since the original implementation by
Vitaliy.
Signed-off-by: Vitaliy Vasylskyy <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Mattijs Korpershoek <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mattijs Korpershoek <[email protected]>
|
|
I'm trying to use dfu-util for bootstrapping an stm32mp board. It
mostly works fine, but something goes horribly wrong as soon as I make
use of the ability to run arbitrary u-boot shell commands. The shell
commands themselves work fine, but the heuristic "dfu_alt_info may
have changed, we have to reinit" seems to cause the board and/or my
host machine to go into some bad state, and further dfu-util commands
fail.
U-Boot already has a mechanism whereby C code can be told about
changes to specific environment variables. So instead of always doing
re-init, add a hook to the dfu_alt_info variable so that we only do
set dfu_reinit_needed if the commands actually did modify that
variable.
Signed-off-by: Rasmus Villemoes <[email protected]>
Reviewed-by: Mattijs Korpershoek <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mattijs Korpershoek <[email protected]>
|
|
Both regulators_enable_boot_on/off() are unused and superseded by
regulator uclass regulator_post_probe(). Remove both functions.
Signed-off-by: Marek Vasut <[email protected]>
|
|
This function is never called, drop it.
Signed-off-by: Marek Vasut <[email protected]>
|
|
regulator_post_probe
Turn regulators_enable_boot_on() and regulators_enable_boot_off() into
empty functions. Implement matching functionality in regulator_post_probe()
instead. The regulator_post_probe() is called for all regulators after they
probe, and regulators that have regulator-always-on or regulator-boot-on DT
properties now always probe due to DM_FLAG_PROBE_AFTER_BIND being set on
such regulators in regulator_post_bind().
Finally, fold regulator_unset() functionality into regulator_autoset().
Signed-off-by: Marek Vasut <[email protected]>
|
|
In case a regulator DT node contains regulator-always-on or regulator-boot-on
property, make sure the regulator gets correctly configured by U-Boot on start
up. Unconditionally probe such regulator drivers. This is a preparatory patch
for introduction of .regulator_post_probe() which would trigger the regulator
configuration.
Parsing of regulator-always-on and regulator-boot-on DT property has been
moved to regulator_post_bind() as the information is required early, the
rest of the DT parsing has been kept in regulator_pre_probe() to avoid
slowing down the boot process.
Signed-off-by: Marek Vasut <[email protected]>
|
|
Prepare v2024.10-rc6
|
|
https://source.denx.de/u-boot/custodians/u-boot-dfu
u-boot-dfu-20240930
- Fix Kconfig dependencies for DFU_OVER_USB
|
|
Transfer initiation and completion for the non-zero Endpoints are
handled by cdns3_ep_run_transfer() and cdns3_transfer_completed()
respectively.
Failing to flush the cache associated with the TRB Pool within
cdns3_ep_run_transfer() results in the transfers never being initiated.
Similarly, failing to invalidate the cache associated with the TRB pool
within cdns3_transfer_completed() results in the transfers never being
completed.
Fix this.
Fixes: 7e91f6ccdc84 ("usb: Add Cadence USB3 host and gadget driver")
Signed-off-by: Siddharth Vadapalli <[email protected]>
Reviewed-by: Roger Quadros <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
The buck variable is zero based, i.e. buck=0 match BUCK1 in datasheet.
Remove any buck + 1 calculation to be more consistent in usage of the
buck variable across the different RK8xx variants in the driver.
Signed-off-by: Jonas Karlman <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
