| Age | Commit message (Collapse) | Author |
|---|
|
dev_read_size() returns -EINVAL (-22) if the property "g-tx-fifo-size"
does not exist. If that's the case, we now keep the default value of 0.
Signed-off-by: Wolfgang Grandegger <[email protected]>
|
|
- sunXi SPI fixups (Andre)
- bcm iproc qspi (Rayagonda)
|
|
The Gigadevice gd25lq128 serial flash exists in different versions,
all which identify themselves using the same JEDEC id.
gd25lq128c:
https://www.gigadevice.com/datasheet/gd25lq128
gd25lq128d:
https://www.gigadevice.com/datasheet/gd25lq128d
However, all versions support quad read, so enable it.
Tested and verified on the Sipeed MAix BiT board.
Fixes: 30b9a28a3f2d ("mtd: spi-nor-ids: Add Gigadevice gd25lq128 ID")
Signed-off-by: Niklas Cassel <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
Ensure the ASPEED related options are grouped together under the RAM
option when enabling support.
This also makes some minor grammar corrections and renames options so
they present cleanly in menuconfig.
There should be no functional change to the configuration or binary.
Signed-off-by: Joel Stanley <[email protected]>
Reviewed-by: Dylan Hung <[email protected]>
|
|
Instead of a special function, send an event after driver model is inited
and adjust the boards which use this function.
Signed-off-by: Simon Glass <[email protected]>
|
|
Generate events when devices are probed or removed, allowing hooks
to be added for these situations.
This is controlled by the DM_EVENT config option.
Signed-off-by: Simon Glass <[email protected]>
|
|
When plat->base is set by driver then skip frame buffer reservation
and allocation.
Signed-off-by: Pali Rohár <[email protected]>
|
|
Fixes the display of the u-boot logo on Apple silicon devices.
Signed-off-by: Janne Grunau <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Ethernet phy like dp83867 is using strapping resistors to setup PHY
address. On Xilinx boards strapping is setup on wires which are connected
to SOC where internal pull ups/downs influnce phy address. That's why there
is a need to setup pins properly (via pinctrl driver for example) and then
perform phy reset. I can be workarounded by reset gpio done for mdio bus
but this is not working properly when multiply phys sitting on the same
bus. That's why it needs to be done via ethernet-phy-id driver where dt
binding has gpio reset per phy.
DT binding is available here:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/ethernet-phy.yaml
The driver is are reading the vendor and device id from valid phy node
using ofnode_read_eth_phy_id() and creating a phy device.
Kconfig PHY_ETHERNET_ID symbol is used because not every platform has gpio
support.
Signed-off-by: Michal Simek <[email protected]>
Signed-off-by: T Karthik Reddy <[email protected]>
Link: https://lore.kernel.org/r/70ab7d71c812b2c972d48c129e416c921af0d7f5.1645627539.git.michal.simek@xilinx.com
|
|
Remove static return type for phy_device_create() to avoid file scope for
this function. Also add required prototype in phy.h.
Signed-off-by: Michal Simek <[email protected]>
Signed-off-by: T Karthik Reddy <[email protected]>
Link: https://lore.kernel.org/r/1517f4053403fbd53e899d500e7485d068a4f0b6.1645627539.git.michal.simek@xilinx.com
|
|
Add new function to get ethernet phy id from compatible property
of the mdio phy node.
Signed-off-by: Michal Simek <[email protected]>
Signed-off-by: T Karthik Reddy <[email protected]>
Link: https://lore.kernel.org/r/16019efb3820a50330935fdaae191cec1f101b5c.1645627539.git.michal.simek@xilinx.com
|
|
During sequential loading of data, hold the bus to prevent controller
from sending stop signal in case no data is available in fifo.
Signed-off-by: Sai Pavan Boddu <[email protected]>
Reviewed-by: Ashok Reddy Soma <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/2407b39d305999cb42438c5423aebc3b514acabb.1646122610.git.michal.simek@xilinx.com
|
|
Start write transfer after loading data to FIFO.
Signed-off-by: Sai Pavan Boddu <[email protected]>
Reviewed-by: Ashok Reddy Soma <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/f0b3e443daa7758e00dfdcc245cf6b2120b0e907.1646122610.git.michal.simek@xilinx.com
|
|
Avoid a race condition where read transaction is started
keeping expected bytes as 0. Which sometimes would result in sending
STOP signal as no data is expected. Observed on QEMU platform.
Signed-off-by: Sai Pavan Boddu <[email protected]>
Reviewed-by: Ashok Reddy Soma <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/487c8026791bfd60719403a2df2c54bb0ae99232.1646122610.git.michal.simek@xilinx.com
|
|
Display Port (DP) has own dma driver that's why add this skeleton driver
only for handling power domain setting and send configuration object to
PMUFW to enable it.
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/fe8bc313bcd430b04e9fa6fb770d5799ef28b350.1645627920.git.michal.simek@xilinx.com
|
|
The reason for this driver is to use call power management driver to enable
it in PMUFW. There is missing functionality now but should be added in
near future.
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/598cb9515bbabc803f72e287464e3d107cd106a3.1645627920.git.michal.simek@xilinx.com
|
|
Add support for dynamic configuration which will takes care of
configuring the SD secure space configuration registers using firmware
APIs, performing SD reset assert and deassert.
High level sequence:
- Check for the PM dynamic configuration support, if no error proceed
with SD dynamic configurations(next steps) otherwise skip the dynamic
configuration.
- Put the SD Controller in reset.
- Configure SD Fixed configurations.
- Configure the SD Slot Type.
- Configure the BASE_CLOCK.
- Configure the 8-bit support.
- Bring the SD Controller out of reset.
In the above steps, apart from the Fixed configurations, remaining all
configurations are dynamic and they will be read from devicetree.
And also remove hardcoded secure register writes, as dynamic sd config
support is added.
Signed-off-by: Ashok Reddy Soma <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/030a3ec041ff3efebd574b4d2b477ad85f12cbce.1645626962.git.michal.simek@xilinx.com
|
|
Add firmware API's to set SD configuration and to check if a purticular
function is supported.
Signed-off-by: Ashok Reddy Soma <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/f64fa2f73e4775e9ad2f4d91339d6c74b43116a3.1645626962.git.michal.simek@xilinx.com
|
|
- serial uclass fix, mailmap/gitignore updates
|
|
The stdout-path property in the device tree does not necessarily
point at a serial device. On machines such as the Apple M1 laptops
where the serial port isn't easy to access and users expect to see
console output on the integrated display stdout-path may point at
the device tree node for the framebuffer for example.
If stdout-path does not point at a node for a serial device, the
serial_check_stdout() will not find a bound device and will drop
down into code that attempts to use lists_bind_fdt() to bind a
device anyway. However, that fallback code does not check that
the uclass of the device is UCLASS_SERIAL. So if stdout-path points
at the framebuffer instead of the serial device it will return a
UCLASS_VIDEO device. Since the code that calls this function
expects the returned device to be a UCLASS_SERIAL device, U-Boot
will crash as soon as it attempts to send output to the console.
Add a check here to verify that the uclass of the bound device
really is UCLASS_SERIAL. If it isn't, serial_check_stdout() will
return an error and serial_find_console_or_panic() will use the
serial device with sequence number 0 as the console and all is fine.
Signed-off-by: Mark Kettenis <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
When running against RC_OSC_32k, the watchdog may suffer from running
faster than expected, expiring earlier. The Linux kernel adds a 10%
margin to the timeout calculation by slowing down the read clock rate
accordingly. Do the same here, also to have comparable preset values
for both drivers.
Along this, fix the name of the local var holding to frequency - in Hz,
not kHz.
Signed-off-by: Jan Kiszka <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
If Armada 37xx watchdog is started before U-Boot then CNTR_CTRL_ACTIVE bit
is set, U-Boot armada-37xx-wdt.c driver fails to initialize and so U-Boot
is unable to use or kick this watchdog.
Do not check for CNTR_CTRL_ACTIVE bit and always initialize watchdog. Same
behavior is implemented in Linux kernel driver.
This change allows to activate watchdog in firmware which loads U-Boot.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Since commit 492ee6b8d0e7 ("watchdog: wdt-uclass.c: handle all DM
watchdogs in watchdog_reset()"), all the watchdog are started when
the config WATCHDOG_AUTOSTART.
To avoid a binary choice none/all, a property u-boot,noautostart
may be added in the watchdog node of the u-boot device tree to not
autostart this watchdog.
Signed-off-by: Philippe Reynes <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
The Aspeed GPIO driver supports the GPIO controllers found in the
AST2400, AST2500 and AST2600 BMC SoCs. The implementation is a cut-down
copy of the upstream Linux kernel driver, adapted for u-boot.
Signed-off-by: Andrew Jeffery <[email protected]>
|
|
In the Linux kernel (v5.16) for this SoC there are two separate drivers
- namely sdhci-omap.c and omap_hsmmc.c which have separate set of
compatibles.
The U-Boot's drivers/mmc/omap_hsmmc.c driver supports both eMMC and
SD devices - hence the compatible for SDHCI can be added.
After this change the am335x DTS description can be easier ported
from Linux kernel.
Signed-off-by: Lukasz Majewski <[email protected]>
Reviewed-by: Jaehoon Chung <[email protected]>
|
|
Add the support of the LED IP for bcm6357. This
LED IP supports blinking, fading and pulsating,
but for the moment, only blinking is supported.
Signed-off-by: Philippe Reynes <[email protected]>
|
|
This IP is also used on some arm SoC, so we allow to
use it on arm bcm6753 too.
Signed-off-by: Philippe Reynes <[email protected]>
|
|
This adds the nand support for chipset bcm6753.
Signed-off-by: Philippe Reynes <[email protected]>
|
|
This IP is also used on some arm SoC, so we allow to
use it on arm bcm6753 too.
Signed-off-by: Philippe Reynes <[email protected]>
|
|
Remove private xpm_configobject[] and use zynqmp_pmufw_node() which
provides the same functionality.
Also add debug messages for easier debugging.
Fixes: e0283cbdfd49 ("power: zynqmp: Add power domain driver for ZynqMP")
Signed-off-by: Michal Simek <[email protected]>
Reviewed-by: Jaehoon Chung <[email protected]>
Link: https://lore.kernel.org/r/bddf11459b9b9e849fac9a50db2f1a5fdfae4119.1646122254.git.michal.simek@xilinx.com
|
|
slg7xl45106 is i2c based 8-bit gpo expander, gpo pins are set and get by
writing and reading corresponding gpo bit value into its data register.
Signed-off-by: T Karthik Reddy <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
Reviewed-by: Heiko Schocher <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Link: https://lore.kernel.org/r/839f475cc75c97ffb3496a4caa93de2faabdbca2.1645629688.git.michal.simek@xilinx.com
|
|
Card detect state stable issue is observed on few ZynqMP boards(SOM),
so enable the workaround 'commit b6f44082d5cd ("mmc: zynq_sdhci: Wait
till sd card detect state is stable")' for ZynqMP platforms also.
Signed-off-by: Ashok Reddy Soma <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/0bf6154c79f24227d786efc5e2c1f506185b2bce.1645625609.git.michal.simek@xilinx.com
|
|
The timeout used in 'commit b6f44082d5cd ("mmc: zynq_sdhci: Wait
till sd card detect state is stable")' workaround is 1000ms at a
granularity of 1msec. Change it to 1usec, to not waste time incase the
cd is stable.
Signed-off-by: Ashok Reddy Soma <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/f008d2bcf864702a01564789f14f9cdecb8acd45.1645625609.git.michal.simek@xilinx.com
|
|
In the workaround added with 'commit b6f44082d5cd ("mmc: zynq_sdhci: Wait
till sd card detect state is stable")' the timeout variable has post
decrement. Whenever timeout happens, this post decrement is making
timeout=0xffffffff, so timeout error print and return statement are
never reached. Fix it by decrementing it inside the while loop.
Signed-off-by: Ashok Reddy Soma <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/61fc1160ada0dd622cd29e381a74af7bf3d9a200.1645625609.git.michal.simek@xilinx.com
|
|
New binding changed node name from flash@e1000000 to nand-controller@0,0
which should be reflected in the driver. Both names are supported for
backward compatibility.
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/61f6edd965e0c0b179184823d5283c6c61a1eb35.1645625433.git.michal.simek@xilinx.com
|
|
Commit 5534fb4f4833 ("arm64: a37xx: pinctrl: Correct PWM pins
definitions") introduced bogus definitions os PWM pins: all 4 pins have
index 11, instead of having indexes 11, 12, 13, 14.
Fix this.
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Pali Rohár <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Replace null pointer by pointer to device registers when calling
armada38x_rtc_write.
Signed-off-by: Francois Berder <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Use "MVPCIE_" prefix instead of generic "PCIE_" prefix for pci_mvebu.c
specific macros. Define offset macros for Root Port registers and use
standard register macros from pci.h when accessing Root Port registers.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Macro SELECT() is unused and struct mvebu_pcie field lane_mask is unused
too. Remove them.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_CHIP_SELECTS_PER_CTRL
Cc: Alison Wang <[email protected]>
Cc: Pramod Kumar <[email protected]>
Cc: Priyanka Jain <[email protected]>
Cc: Rajesh Bhagat <[email protected]>
Cc: Vladimir Oltean <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
Signed-off-by: Tom Rini <[email protected]>
|
|
Remove some code, primarily CPM2 related, that is now unused since the
removal of MPC8540/60ADS.
Fixes 3913191c8a6b ("powerpc: mpc8540ads: mpc8560ads: Drop support for MPC8540/60ADS")
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Update and fixes for sl28, lx2, pblimage generation for some powerpc
products
|
|
Implements SCMI APIs to retrieve the number exposed SCMI clocks using
SCMI_PROTOCOL_ATTRIBUTES messages and the names of the clocks using
SCMI_CLOCK_ATTRIBUTES messages.
This change updates sandbox SCMI clock test driver to manage these
2 new message IDs.
Cc: Lukasz Majewski <[email protected]>
Cc: Sean Anderson <[email protected]>
Cc: Clement Leger <[email protected]>
Cc: Patrick Delaunay <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
Signed-off-by: Gabriel Fernandez <[email protected]>
Signed-off-by: Etienne Carriere <[email protected]>
|
|
Updates sandbox SCMI clock driver and tests since enabling CCF will
mandate clock discovery that is all exposed SCMI clocks shall be
discovered at initialization. For this reason, sandbox SCMI clock
driver must emulate all clocks exposed by SCMI server, not only those
effectively consumed by some other U-Boot devices.
Therefore the sandbox SCMI test driver exposes 3 clocks (IDs 0, 1 and 2)
and sandbox SCMI clock consumer driver gets 2 of them.
Cc: Simon Glass <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
Signed-off-by: Etienne Carriere <[email protected]>
|
|
Changes devm_scmi_process_msg() first argument from target parent device
to current SCMI device and lookup the SCMI agent device among SCMI device
parents for find the SCMI agent operator needed for communication with
the firmware.
This change is needed in order to support CCF in clk_scmi driver unless
what CCF will fail to find the right udevice related to exposed SCMI
clocks.
This patch allows to simplify the caller sequence, using SCMI device
reference as parameter instead of knowing SCMI uclass topology. This
change also adds some protection in case devm_scmi_process_msg() API
function is called for an invalid device type.
Cc: Lukasz Majewski <[email protected]>
Cc: Sean Anderson <[email protected]>
Cc: Jaehoon Chung <[email protected]>
Cc: Patrick Delaunay <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
Signed-off-by: Etienne Carriere <[email protected]>
|
|
As per DT bindings since Linux kernel v5.14, the device tree can define
only 1 SCMI agent node that is named scmi [1]. As a consequence, change
implementation of the SCMI driver test through sandbox architecture to
reflect that.
This change updates sandbox test DT and sandbox SCMI driver accordingly
since all these are impacted.
Cc: Simon Glass <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
Signed-off-by: Etienne Carriere <[email protected]>
|
|
Ensure there is a valid reset-gpio defined before using it.
Fixes: f9852acdce02 ("phy: nop-phy: Fix enabling reset")
Cc: Adam Ford <[email protected]>
Signed-off-by: Tim Harvey <[email protected]>
|
|
The gpio block is part of the sl28cpld sl28cpld management controller.
There are three different flavors: the usual input and output where the
direction is configurable, but also input only and output only variants.
Signed-off-by: Michael Walle <[email protected]>
[Rebased]
Signed-off-by: Priyanka Jain <[email protected]>
|
|
The watchdog timer is part of the sl28cpld management controller. The
watchdog timer usually supervises the bootloader boot-up and if it bites
the failsafe bootloader will be activated. Apart from that it supports
the usual board level reset and one SMARC speciality: driving the
WDT_TIMEOUT# signal.
Signed-off-by: Michael Walle <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
