| Age | Commit message (Collapse) | Author |
|---|
|
On reset, the RTC loads the 2000-01-01 date with a wrong day of the
week (Sunday instead of Saturday).
Signed-off-by: Dario Binacchi <[email protected]>
Signed-off-by: Lokesh Vutla <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Update the driver to support the device tree and the driver model.
The read / write helpers in rtc_ops allow access to scratch registers
only. The offset parameter is added to the address of the scratch0
register.
Support for non-DM has been removed as there were no users.
Signed-off-by: Dario Binacchi <[email protected]>
Signed-off-by: Lokesh Vutla <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
The RTC module contains a kicker mechanism to prevent any spurious
writes from changing the register values. To set the time, you must
first unlock the TC registers, update them and then lock.
Signed-off-by: Dario Binacchi <[email protected]>
Signed-off-by: Lokesh Vutla <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
To write correct data to the TC registers, the STATUS register must be
read until the BUSY bit is equal to zero. Once the BUSY flag is zero,
there is a 15 μs access period in which the TC registers can be
programmed.
The rtc_wait_not_busy() has been inspired by the Kernel.
Signed-off-by: Dario Binacchi <[email protected]>
Signed-off-by: Lokesh Vutla <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Use 32-bit access only where it is needed. Most of the RTC registers
contain useful information in the 8 least significant bits, the others
are reserved.
Signed-off-by: Dario Binacchi <[email protected]>
Signed-off-by: Lokesh Vutla <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Fix errors raised by module compilation.
Signed-off-by: Dario Binacchi <[email protected]>
Signed-off-by: Lokesh Vutla <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
The Davinci's onchip RTC is also present on TI OMAP1, AM33XX, AM43XX and
DRA7XX SOCs. So, let's enable compilation for these architectures too.
Signed-off-by: Dario Binacchi <[email protected]>
Signed-off-by: Lokesh Vutla <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
- dwc2 and cdns3 fixes
|
|
Add support for usb1 and usb2 present on i.IMXRT.
Signed-off-by: Giulio Benetti <[email protected]>
|
|
Usb needs IMXRT1050_CLK_USBOH3 clock to be enabled, so let's add it to
clock driver.
Signed-off-by: Giulio Benetti <[email protected]>
|
|
Lcd peripheral needs 2 different gates to be enable to work, so let's
introduce the missing one(LCDIF_PIX) and rename the existing one
(LCDIF_APB).
Signed-off-by: Giulio Benetti <[email protected]>
|
|
Some SoC needs "disp_axi" clock to be enabled, so let's try to retrieve it
and enabling. If it fails it gives only a debug(), but this clock as well
as "axi" clock is not mandatory.
Signed-off-by: Giulio Benetti <[email protected]>
|
|
On some SoC mxsfb needs more than one clock gate(actual "per" clock). So
let's introduce "axi" clock that can be provided but it's not mandatory.
This is inspired from linux mxsfb driver. Also let's rename "per" clock to
"pix" clock for compatibility with already existing .dts lcdif nodes
implementation.
Signed-off-by: Giulio Benetti <[email protected]>
|
|
This timer driver uses GPT Timer (General Purpose Timer) available on
a lot of i.MX SoCs family. This driver deals with both 24Mhz oscillator
as well as peripheral clock.
Signed-off-by: Giulio Benetti <[email protected]>
[Giulio: added the driver's stub and handled peripheral clock prescaler
setting making driver to work correctly]
Signed-off-by: Jesse Taube <[email protected]>
[Jesse: added init, setting prescaler for 24Mhz support and enabling
timer]
|
|
When `usb start` is called on the terminal, the dwc2 driver will try
to start every USB device as host first, even if it is explicitly
configured as peripheral in the device tree (dr_mode = "peripheral").
So to avoid an unwanted 15 seconds delay when initializing the usb
(one second per channel = 1s x 15), this patch adds a check to the
initialization, and will skip host initialization of the device is
explicitly set as peripheral. The checking is already done similarly
in the `drivers/usb/gadget/dwc2_udc_otg.c` driver.
Signed-off-by: João Loureiro <[email protected]>
|
|
CONFIG_SYS_DFU_MAX_FILE_SIZE to Kconfig
Currently the config options CONFIG_SYS_DFU_DATA_BUF_SIZE and
CONFIG_SYS_DFU_MAX_FILE_SIZE are being set in include/configs/<board>.h
files and also in <board_name>_defconfig files without a Kconfig option. It
is easier for users to set these configs in defconfig files than in config
header files as they are a part of the source code.
Add Kconfig symbols, and update the defconfigs by using tools/moveconfig.py
script.
Suggested-by: Pratyush Yadav <[email protected]>
Signed-off-by: Aswath Govindraju <[email protected]>
Acked-by: Oleksandr Suvorov <[email protected]>
Acked-by: Matthias Brugger <[email protected]>
Acked-by: Lukasz Majewski <[email protected]>
|
|
Kernel device tree got updated to use clock name as "ref" instead of
"usb2_refclk". Fix cdns3-ti.c to use the correct name.
Fixes: 70e167495ab2 ("arm: dts: k3-j721e: Sync Linux v5.11-rc6 dts into U-Boot")
Fixes: 6239cc8c4e84 ("arm: dts: k3-j7200: Sync Linux v5.11-rc6 dts into U-Boot")
Signed-off-by: Kishon Vijay Abraham I <[email protected]>
Signed-off-by: Aswath Govindraju <[email protected]>
|
|
Synchronize R-Car Gen2/Gen3 pinctrl tables with Linux 5.12,
commit 9f4ad9e425a1 ("Linux 5.12") . This is a rather large
commit, since the macros in sh-pfc.h also got updated, so
all the PFC tables must be updated in lockstep.
Signed-off-by: Marek Vasut <[email protected]>
|
|
Not correcting anything in case of empty ECC data area
is not an appropriate strategy, because an uncorrected bit-flip
in an empty sector may cause upper layers (namely UBI) fail to work
properly. Therefore the approach chosen in Linux kernel and other
u-boot mtd drivers has been adopted, where a heuristic implemented
by nand_check_erased_ecc_chunk() is used in order to detect and
correct empty sectors.
Tested with sama5d3_xplained and sam9x60-ek.
Signed-off-by: Kai Stuhlemmer (ebee Engineering) <[email protected]>
Tested-by: Tudor Ambarus <[email protected]>
[ta: reorder if conditions, change commit subject, s/uint8_t/u8.]
Signed-off-by: Tudor Ambarus <[email protected]>
|
|
Removed call of ofnode_translate_address() after ofnode_read_resource
in luton_switch.c:luton_probe(); it is unnecessary since
the commit feb7ac457c20 ("dm: core: Add address translation in
fdt_get_resource").
Fixes: feb7ac457c20 ("dm: core: Add address translation in fdt_get_resource")
Reviewed-by: Ramon Fried <[email protected]>
Reported-by: Horatiu Vultur <[email protected]>
Signed-off-by: Patrick Delaunay <[email protected]>
|
|
With commit 41575d8e4c33 ("dm: treewide: Rename auto_alloc_size members
to be shorter") "priv_auto_alloc_size" was renamed to "priv_auto". This
driver was sent to the mailing list before that change, merged after it,
and still has the old form. Apply the rename here as well.
Fixes: 1b9ee2882e6b ("pwm: Add a driver for Chrome OS EC PWM")
Signed-off-by: Alper Nebi Yasak <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
In of_get_address(), there is:
dev_count_cells(dev, &na, &ns);
followed by:
bus->count_cells(dev, &na, &ns);
but no codes in between use na/ns, hence the first call is useless.
By dropping the first call, dev_count_cells() is now useless too.
Signed-off-by: Bin Meng <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
'dma-ranges' frequently exists without parent nodes having 'dma-ranges'.
While this is an error for 'ranges', this is fine because DMA capable
devices always have a translatable DMA address. Also, with no
'dma-ranges' at all, the assumption is that DMA addresses are 1:1 with
no restrictions unless perhaps the device itself has implicit
restrictions.
This keeps in sync with Linux kernel commit:
81db12ee15cb: of/address: Translate 'dma-ranges' for parent nodes missing 'dma-ranges'
Signed-off-by: Bin Meng <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
The `ranges` DT property of the PCIe node is currently ignored by
Aardvark driver - all entries are used as transparent PCIe MEM, despite
some of them being defined for IO in DT.
This is because the driver does not setup PCIe outbound windows and thus
a default configuration is used.
This can cause an external abort on CPU when a device driver tries to
access non-MEM space.
Setup the PCIe windows according to the `ranges` property for all
non-MEM resources (currently only IO) and also non-transparent MEM
resources.
Because Linux expects that bootloader does not setup Aardvark PCIe
windows, disable them before booting Linux.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Change DT compatible string for A3700 PCIe from 'marvell,armada-37xx-pcie'
to 'marvell,armada-3700-pcie' to make U-Boot A3700 PCIe DT node compatible
with Linux' DT node.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Disable Root Bridge I/O space, memory space and bus mastering in Aardvark's
remove method, which is called before booting Linux kernel.
This ensures that PCIe device which was initialized and used by U-Boot
cannot do new DMA transfers until Linux initializes PCI subsystem and loads
appropriate drivers for the device.
During initialization of PCI subsystem Linux in fact disables this bus
mastering on Root Bridge (and later enables it when driver is loaded and
configured), but there is a possibility of a small window after U-Boot
boots Linux when bus mastering is enabled, which is not correct.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
During our debugging of the Aardvark driver in Linux we have discovered
that the PCIE_CORE_LINK_CTRL_STAT_REG register in fact controls standard
PCIe Link Control Register for PCIe Root Bridge. This led us to discover
that the name of the PCIE_CORE_LINK_TRAINING macro and the corresponding
comment by this macro's usage is misleading; this bit in fact controls
Retrain Link, which, according to PCIe base spec is defined as:
A write of 1b to this bit initiates Link retraining by directing the
Physical Layer LTSSM to the Recovery state. If the LTSSM is already in
Recovery or Configuration, re-entering Recovery is permitted but not
required.
Entering Recovery state is normally done from LTSSM L0, L0s and L1 states.
But since the pci-aardvark.c driver enables Link Training just a few lines
above, the controller is not in L0 ready state yet. So setting aardvark bit
PCIE_CORE_LINK_TRAINING does not actually enter Recovery state at this
place.
Moreover, trying to enter LTSSM Recovery state without other configuration
is causing issues for some cards (e.g. Atheros AR9xxx and QCA9xxx). Since
Recovery state is not entered, these issues are not triggered.
Remove code which tries to enter LTSSM Recovery state completely.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Fix compilation error when Werror is turned on. The warning could
possible break some CI builds.
Signed-off-by: Green Wan <[email protected]>
Reviewed-by: Leo Yu-Chi Liang <[email protected]>
|
|
Add defconfig and board support for HiFive Unmatched.
Signed-off-by: Green Wan <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
Reviewed-by: Rick Chen <[email protected]>
|
|
Add pcie driver for SiFive fu740, the driver depends on
fu740 gpio, clk and reset driver to do init. Force running at Gen1
for better capatible enumeration.
Several devices are tested:
a) M.2 NVMe SSD
b) USB-to-PCI adapter
c) Ethernet adapter (E1000 compatible)
Signed-off-by: Green Wan <[email protected]>
Reviewed-by: Neil Armstrong <[email protected]>
|
|
Rename fu540_ddr.c to sifive_ddr.c and add fu740 support
Signed-off-by: Green Wan <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
Add fu740 support. One abstract layer is added for supporting
multiple chips such as fu540 and fu740.
Signed-off-by: Green Wan <[email protected]>
|
|
BITS_PER_LONG is used to represent register's size which is 32.
But when compiled on arch64, BITS_PER_LONG is then equal to 64.
Fix bank and offset computation to make it work on arch32 and
arch64 and ensure that register's size is always equal to 32.
Signed-off-by: Patrice Chotard <[email protected]>
Signed-off-by: Pankaj Dev <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
|
|
Fix the result of DFU_OP_WRITE operation in mtd_block_op function
when mtd_lock is not supported (-EOPNOTSUPP) to avoid DFU stack
error on the DFU manifestation of the MTD device, when
dfu_flush_medium_mtd is called.
Without this patch, dfu-util failed on dfuERROR state at the end
of the write operation on the alternate even if MTD write
opeartion is correctly performed.
$> dfu-util -a 3 -D test.bin
....
DFU mode device DFU version 0110
Device returned transfer size 4096
Copying data from PC to DFU device
....
Download [=========================] 100% 225469 bytes
Download done.
state(10) = dfuERROR, status(14) = Something went wrong,
but the device does not know what it was Done!
Fixes: 65f3fc18fc1e ("dfu_mtd: Add provision to unlock mtd device")
Signed-off-by: Patrick Delaunay <[email protected]>
Acked-by: Sughosh Ganu <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-ti
- Fix reset for AM64 platforms
- Enable networking PHY driver for AM64
- Fix default R5F cluster setting in J7
|
|
The ti_sci_msg_req_reboot message payload has been extended to include a
domain field, but for the purposes of u-boot this should be zero to
reset the entire SoC as it did before. Include domain for completeness
and set to zero to ensure proper operation.
Signed-off-by: Dave Gerlach <[email protected]>
Signed-off-by: Suman Anna <[email protected]>
Signed-off-by: Lokesh Vutla <[email protected]>
|
|
If reg property of pinctrl-single node requires address translation then
probe fails with following message:
single-pinctrl pinctrl@4301c000: failed to get base register size
This is because driver uses dev_read_addr_size() to get size which also
tries to fetch untranslated addr and fails.
Fix this by using dev_read_addr_size_index() which takes care of address
translation and also makes following dev_read_addr() call redundant.
This fixes Ethernet failures on TI's AM654 based EVMs due to lack of
pinmux configuration.
Fixes: 9fd8a430f3 ("pinctrl: single: get register area size by device API")
Signed-off-by: Vignesh Raghavendra <[email protected]>
|
|
With the last user of this driver removed, remove the driver.
Reviewed-by: Daniel Schwierzeck <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
When building highbank_defconfig with LTO, the compiler complains about
type mismatch of function ahci_link_up().
The third parameter of this function is of type u8 in
drivers/ata/ahci.c, but of type int in board/highbank/ahci.c.
There is no reason in using u8, and the code using this function
actually passes an int variable into the function (so it is implicitly
converted to u8).
Change the type of this parameter to int in drivers/ata/ahci.c.
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
When apf27_defconfig is built with LTO, linking complains about
undefined reference to `nand_boot`. This is because it is referenced
from inline assembly. Make it visible.
Signed-off-by: Marek Behún <[email protected]>
|
|
This commit does the same thing as Linux commit 33def8498fdd.
Use a more generic form for __section that requires quotes to avoid
complications with clang and gcc differences.
Remove the quote operator # from compiler_attributes.h __section macro.
Convert all unquoted __section(foo) uses to quoted __section("foo").
Also convert __attribute__((section("foo"))) uses to __section("foo")
even if the __attribute__ has multiple list entry forms.
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
There is a serious bug in regmap_read() and regmap_write() functions
where an uint pointer is cast to (void *) which is then cast to (u8 *),
(u16 *), (u32 *) or (u64 *), depending on register width of the map.
For example given a regmap with 16-bit register width the code
int val = 0x12340000;
regmap_read(map, 0, &val);
only changes the lower 16 bits of val on little-endian machines.
The upper 16 bits will remain 0x1234.
Nobody noticed this probably because this bug can be triggered with
regmap_write() only on big-endian architectures (which are not used by
many people anymore), and on little endian this bug has consequences
only if register width is 8 or 16 bits and also the memory place to
which regmap_read() should store it's result has non-zero upper bits,
which it seems doesn't happen anywhere in U-Boot normally. CI managed to
trigger this bug in unit test of dm_test_devm_regmap_field when compiled
for sandbox_defconfig using LTO.
Fix this by utilizing an union { u8; u16; u32; u64; } and reading data
into this union / writing data from this union.
Signed-off-by: Marek Behún <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Heiko Schocher <[email protected]>
Cc: Bin Meng <[email protected]>
Cc: Pratyush Yadav <[email protected]>
|
|
- Various clk/pinctrl updates to re-sync with Linux and other fixes
|
|
The V3U SoC has several unlock registers, one per register group. They
reside at offset zero in each 0x200 bytes-sized block.
To avoid adding yet another table to the PFC implementation, this
patch adds the option to specify an address mask instead of the fixed
address in sh_pfc_soc_info::unlock_reg.
This is a direct port of Linux 5.12 commit e127ef2ed0a6
("pinctrl: renesas: Implement unlock register masks") by
Ulrich Hecht <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
|
|
The help text for Gen2 entries had a copy paste error, still containing
the Gen3 string, while the description was correctly listing Gen2. Fix
the help text.
Signed-off-by: Marek Vasut <[email protected]>
|
|
The help text in the Kconfig file was always a copy of the same thing.
Move single copy into the common PFC driver entry instead. Also fix a
copy-paste error in the PFC help text, which identified PFC as clock.
Signed-off-by: Marek Vasut <[email protected]>
|
|
Pass struct udevice to rcar_gpio_set_direction() in preparation of
quirk handling in rcar_gpio_set_direction(). No functional change.
Signed-off-by: Marek Vasut <[email protected]>
|
|
Most of the PLLx, MAIN, FIXED clock handlers are calling very similar
code, which determines parent rate and then applies multiplication and
division. The only difference is whether multiplication is fixed factor
or coming from CRx register. Deduplicate the code into a single function.
Signed-off-by: Marek Vasut <[email protected]>
|
|
Base on Linux v5.10-rc2, commit 8b652aa8a1fb by Yoshihiro Shimoda
To support other register layouts in the future, add register pointers
of {control,status,reset,reset_clear}_regs into struct cpg_mssr_info
Signed-off-by: Hai Pham <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
|
|
From Linux v5.10-rc2, commit ffbf9cf3f946 by Yoshihiro Shimoda
Introduce enum clk_reg_layout to support multiple register layout variants
Signed-off-by: Hai Pham <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
|
