| Age | Commit message (Collapse) | Author |
|---|
|
Synchronize Gen2 MSTP teardown tables with datasheet Rev.2.00
Feb 01, 2016. This corrects the following bits:
- added H2 MSTP3[10] SCIF2
- added H2/M2/E2 MSTP7[29] TCON
- removed E2 MSTP5[22] Thermal Sensor
- removed E2 MSTP10[31,24:22] SRC0, SRC7:9
Signed-off-by: Marek Vasut <[email protected]>
Cc: Nobuhiro Iwamatsu <[email protected]>
|
|
The clock driver used a heavy-handed approach where it turned off
all available clocks, while also possibly setting bits which are not
documented in the R-Car datasheet. Update the tables so that only
the bits which are documented are set or cleared when tearing down
the clock driver.
Note that the only clock left running before booting Linux are now
MFIC, INTC-AP, INTC-EX and SCIF2 / SCIF0 on V3x.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Nobuhiro Iwamatsu <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Tom Rini <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-mips
- MIPS: octeon: fix minor bugs of initial merge
- MIPS: octeon: add support for QLM and PCI-E controller
- MIPS: octeon: add support for AHCI and SATA
- MIPS: octeon: add E1000 ethernet support
- MIPS: octeon: add Octeon III NIC23 board
- ata/scsi: add support for Big Endian platforms
|
|
Currently DE2 driver uses functions which are defined in internal
headers. They are not meant to be used outside of uclass framework.
Switch DE2 driver to public ones. This has additional benefit that
device_probe doesn't need to be called manually.
Signed-off-by: Jernej Skrabec <[email protected]>
Reviewed-by: Andre Przywara <[email protected]>
Signed-off-by: Andre Przywara <[email protected]>
|
|
There is no real need to read source_id at probe time. It also doesn't
make sense to store it in driver private data since it's already stored
in class platform data. While this looks like cleanup (and it is), it's
also important for DE2 driver rework because this info will be filled
later (after probe is already executed).
Signed-off-by: Jernej Skrabec <[email protected]>
Reviewed-by: Andre Przywara <[email protected]>
Signed-off-by: Andre Przywara <[email protected]>
|
|
TV driver was never fully implemented. Remove search for it from DE2
driver.
Reviewed-by: Andre Przywara <[email protected]>
Signed-off-by: Jernej Skrabec <[email protected]>
Signed-off-by: Andre Przywara <[email protected]>
|
|
No Allwinner board with DW-HDMI controller use separate I2C bus for
EDID read. Remove that check.
Reviewed-by: Andre Przywara <[email protected]>
Signed-off-by: Jernej Skrabec <[email protected]>
Signed-off-by: Andre Przywara <[email protected]>
|
|
It turns out that there are two ways how hot plug detection can be done.
One is standard way for DW HDMI controller - checking bit 2 in 0x3004
register. Another way is applicable only to Allwinner custom PHY - by
checking bit 19 in register 0x10038. Both methods are equally good as
far as we know.
Use standard method in order to reduce amount of custom code.
Reviewed-by: Andre Przywara <[email protected]>
Signed-off-by: Jernej Skrabec <[email protected]>
Signed-off-by: Andre Przywara <[email protected]>
|
|
Currently driver accepts all resolution which won't work on 4k screens.
Add validation callback which limits acceptable resolutions to 297 MHz.
Reviewed-by: Andre Przywara <[email protected]>
Signed-off-by: Jernej Skrabec <[email protected]>
Signed-off-by: Andre Przywara <[email protected]>
|
|
Otherwise the output will look like this on MIPS Octeon NIC23:
Device 0: (0:0) Vendor: ATA Prod.: aSDnsi klUrt aII Rev: 4X11
Type: Hard Disk
Capacity: 457862.8 MB = 447.1 GB (937703088 x 512)
instead of this version:
Device 0: (0:0) Vendor: TA Prod.: SanDisk Ultra II Rev: X411
Type: Hard Disk
Capacity: 457862.8 MB = 447.1 GB (937703088 x 512)
Signed-off-by: Stefan Roese <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Aaron Williams <[email protected]>
Cc: Chandrakala Chavva <[email protected]>
Cc: Daniel Schwierzeck <[email protected]>
|
|
This patch adds a few missing virt_to_phys() to use the correct physical
address for DMA operations in the common AHCI code. This is done to
support the big-endian MIPS Octeon platform.
Additionally the code a cleaned up a bit (remove some empty lines) and
made a bit better readable.
Signed-off-by: Stefan Roese <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Aaron Williams <[email protected]>
Cc: Chandrakala Chavva <[email protected]>
Cc: Daniel Schwierzeck <[email protected]>
|
|
This patch enables the usage of the MVEBU AHCI/SATA driver. The only
changes necessary to support MIPS Octeon via DT based probing are, to
add the compatible DT property and the use of dev_remap_addr() so that
the correct mapped address is used in the Octeon case (phys != virt).
Please note that this driver supports the usage of the "scsi" command
and not the "sata" command, since it does not provide an own "scan"
function, which is needed for the "sata" cmd support.
Signed-off-by: Stefan Roese <[email protected]>
Cc: Aaron Williams <[email protected]>
Cc: Chandrakala Chavva <[email protected]>
Cc: Daniel Schwierzeck <[email protected]>
|
|
This patch adds the PCI bootcmd feature for MIPS Octeon, which will be
used by the upcoming Octeon III NIC23 board support. It enables the use
of the "oct-remote-load" and "oct-remote-bootcmd" on host PC's to
communicate with the PCIe target and load images into the onboard
memory and issue commands.
Signed-off-by: Stefan Roese <[email protected]>
Cc: Aaron Williams <[email protected]>
Cc: Chandrakala Chavva <[email protected]>
Cc: Daniel Schwierzeck <[email protected]>
|
|
This patch adds the PCI remote console feature for MIPS Octeon, which
will be used by the upcoming Octeon III NIC23 board support. It enables
the use of the "oct-remote-console" tool on host PC's to communicate
with the PCIe target.
Signed-off-by: Stefan Roese <[email protected]>
Cc: Aaron Williams <[email protected]>
Cc: Chandrakala Chavva <[email protected]>
Cc: Daniel Schwierzeck <[email protected]>
|
|
This patch adds the PCIe host controller driver for MIPS Octeon II/III.
The driver mainly consist of the PCI config functions, as all of the
complex serdes related port / lane setup, is done in the serdes / pcie
code available in the "arch/mips/mach-octeon" directory.
Signed-off-by: Stefan Roese <[email protected]>
Cc: Aaron Williams <[email protected]>
Cc: Chandrakala Chavva <[email protected]>
Cc: Daniel Schwierzeck <[email protected]>
|
|
With the newly added headers and their restructuring (which macro is
defined where), some changes in the already existing Octeon files are
necessary. This patch makes the necessary changes.
Signed-off-by: Stefan Roese <[email protected]>
|
|
|
|
Trivial typo fix.
Signed-off-by: Michal Simek <[email protected]>
|
|
According to EHCI spec, software needs to do handshake with HC for
safely removing QH from async list. This handshake is implemented by
setting IAAD (Interrupt on Async Advance Doorbell) bit in USB_USBCMD
register and poll the IAA (Interrupt on Async Advance bit) in the
USB_USBSTS to ensure the HC has released all on-chip state that may
potentially reference one of the data structures just removed.
Current codes only check active status of the last QTD, but this can't
ensure the QH is released from HC. We can meet unrecoverable
"EHCI timed out on TD" errors when running UEFI SCT tests on USB disk.
The USB_ASYNCLISTADDR register is changed to a invalid address when the
issue happens. It is fixed after adding the IAA handshake.
Steps to reproduce the issue:
1. Build the UEFI SCT from https://github.com/tianocore/edk2-test
2. Build the EDK2 UEFI Shell from https://github.com/tianocore/edk2
3. Copy SCT files and Shell.efi to USB disk FAT partition
4. Load the Shell.efi from USB FAT, and run bootefi to execute it
5. After booting into Shell, enter the SCT directory and run "sct -a"
to execute all tests.
6. Tests run about 1 hour and stop with many EHCI timeout errors like
EHCI timed out on TD - token=0x801f8c80
Signed-off-by: Ye Li <[email protected]>
|
|
Until now, the Octeontx MMC driver did only support the ARM Octeon
TX/Tx2 platforms. This patch adds support for the MIPS Octeon platform
to this driver. Here a short summary of the changes:
- Enable driver compilation for MIPS Octeon, including the MMC related
header file
- Reorder header inclusion
- Switch to using the clk framework to get the input clock
- Remove some functions for MIPS Octeon, as some registers don't
exist here
Signed-off-by: Stefan Roese <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Aaron Williams <[email protected]>
Cc: Chandrakala Chavva <[email protected]>
Cc: Daniel Schwierzeck <[email protected]>
|
|
Sometimes no traffic was getting out on the ports, the root cause was
a wrong configuration of the Serdes6G, which is used on jr2 pcb111.
This patch fixes this issue by applying the correct configuration.
Fixes: 5e1d417bec92ac ("net: Add MSCC Jaguar2 network driver.")
Signed-off-by: Horatiu Vultur <[email protected]>
Reviewed-by: Ramon Fried <[email protected]>
|
|
Make sure to reset the switch core at probe time.
Signed-off-by: Horatiu Vultur <[email protected]>
Reviewed-by: Ramon Fried <[email protected]>
|
|
Add additional param for reset cmd, which provides type of reset.
Signed-off-by: Igor Opaniuk <[email protected]>
|
|
Use psci driver exported functions for reset/poweroff, instead of
invoking directly invoke_psci_fn.
Signed-off-by: Igor Opaniuk <[email protected]>
|
|
Adds support for:
* PSCI_FEATURES, which was introduced in PSCI 1.0. This provides API
that allows discovering whether a specific PSCI function is implemented
and its features.
* SYSTEM_RESET2, which was introduced in PSCI 1.1, which extends existing
SYSTEM_RESET. It provides support for vendor-specific resets, providing
reset_type as an additional param.
For additional details visit [1].
Implementations of some functions were borrowed from Linux PSCI driver
code [2].
[1] https://developer.arm.com/documentation/den0022/latest/
[2] drivers/firmware/psci/psci.c
Signed-off-by: Igor Opaniuk <[email protected]>
|
|
To squash that nasty warning message and make better use of the newly
gained OF_CONTROL feature, let's convert the calxedagmac driver to the
"new" driver model.
The conversion is pretty straight forward, mostly just adjusting the
use of the involved data structures.
The only actual change is the required split of the receive routine into
a receive and free_pkt part.
Also this allows us to get rid of the hardcoded platform information and
explicit init calls.
This also uses the opportunity to wrap the code decoding the MMIO
register base address, to make it safe for using PHYS_64BIT later.
Signed-off-by: Andre Przywara <[email protected]>
Reviewed-by: Ramon Fried <[email protected]>
|
|
Anatop is an integrated regulator inside i.MX6 SoC.
There are 3 digital regulators which controls PU, CORE (ARM), and SOC.
And 3 analog regulators which controls 1P1, 2P5, 3P0 (USB).
This patch adds the Anatop regulator driver.
Signed-off-by: Ying-Chun Liu (PaulLiu) <[email protected]>
Reviewed-by: Sean Anderson <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Jaehoon Chung <[email protected]>
Cc: Peng Fan <[email protected]>
Reviewed-by: Jaehoon Chung <[email protected]>
|
|
The fdt node offset is apparently not set properly when probed
causing no MDIO busses to be found. Fix this by obtaining the
offset.
Signed-off-by: Tim Harvey <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
After check for maximum between max id and available ports, also check
if available port count is less than max id and update.
In the case of the CN8030 OcteonTX SoC max_id needs to be reduced to
the number of ports found otherwise the following occurs on a scan:
GW6404-B> scsi scan
scanning bus for devices...
Target spinup took 0 ms.
AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
flags: 64bit ncq ilck stag pm led clo only pmp fbss pio slum part ccc
apst
Device 0: (0:0) Vendor: ATA Prod.: SanDisk SD8SFAT0 Rev: Z233
Type: Hard Disk
Capacity: 61057.3 MB = 59.6 GB (125045424 x 512)
"Synchronous Abort" handler, esr 0x96000006
elr: 000000000052f824 lr : 000000000052fa10 (reloc)
elr: 000000007fee9824 lr : 000000007fee9a10
x0 : 0000000000000001 x1 : 0000000000000001
x2 : 000000007bea3528 x3 : 000000007bea3580
x4 : 0000000000000200 x5 : 0000000000000000
x6 : 0000000000000002 x7 : 000000007bea3540
x8 : 00000000fffffff8 x9 : 0000000000000008
x10: 00000000000186a0 x11: 000000000000000d
x12: 0000000000000006 x13: 000000000001869f
x14: 0000000000000007 x15: 00000000ffffffff
x16: 000000007ff439a5 x17: 000000007ff5730c
x18: 000000007bea9de0 x19: 000000007ff7a580
x20: 000000007bec79f8 x21: 0000000000000000
x22: 000000007bea3580 x23: 0000000000000000
x24: 0000000000000000 x25: 000000007bec7a00
x26: 00000000ffffffc0 x27: 000000007bec79d0
x28: 000000007beb51c0 x29: 000000007bea3480
Code: 91246800 940130c2 12800000 1400004f (b9402ae0)
Resetting CPU ...
Signed-off-by: Suneel Garapati <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Revert a change that occured between the Marvell SDK-10.1.1.0
and SDK-10.3.1.1 which broke QSMII phy support.
Signed-off-by: Tim Harvey <[email protected]>
|
|
Fixes IDE issues found on the Malta board under Qemu:
1) DMA implied commands were sent to the controller in stead of the PIO
variants. The rest of the code is DMA free and written for PIO operation.
2) direct pointer access was used to read and write the registers instead
of the inb/inw/outb/outw functions/macros. Registers don't have to be
memory mapped and ATA_CURR_BASE() does not have to return an offset from
address zero.
3) Endian isues in ide_ident() and reading/writing data in general. Names
were corrupted and sizes misreported.
Tested malta_defconfig and maltael_defconfig to work again in Qemu.
Signed-off-by: Reinoud Zandijk <[email protected]>
Tested-by: Heinrich Schuchardt <[email protected]>
|
|
UCLASS_IRQ driver is not Intel specific. Make CONFIG_IRQ
selectable for all platforms.
Signed-off-by: Wasim Khan <[email protected]>
Tested-by: Vladimir Oltean <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Add the PCIe part of the G12A USB3 PCIe Combo PHY driver.
Signed-off-by: Neil Armstrong <[email protected]>
|
|
Add missing gates used for PCIe.
Signed-off-by: Neil Armstrong <[email protected]>
|
|
Add support for sama7g5 pinctrl variant, with 5 banks with a degraded
8 line only 5th bank.
Based on Linux Kernel implementation.
Signed-off-by: Eugen Hristev <[email protected]>
|
|
This is a patchset which makes away with the .bind() controller indexing
workaround which was broken since before v2021.04, and then adds PHY
support and MX8M support on top of that. Better add it into the release
early to get as much testing as possible done, because this really does
a lot of changes to the ehci-mx6 driver.
|
|
https://source.denx.de/u-boot/custodians/u-boot-ti
- Support for pinmux status command on beaglebone
- Updates for MMC speed modes for J721e-evm
- Fix MMC booting on omap35_logic_somlv board
|
|
The iMX8M uses nop PHY, select PHY and NOP_PHY automatically.
Otherwise, the DM capable driver is now perfectly compatible.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Ye Li <[email protected]>
Cc: uboot-imx <[email protected]>
|
|
Fix cast from pointer to integer of different size by casting the
pointer to uintptr_t instead of uint32_t, the former has correct
size on both 32bit and 64bit architectures.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Ye Li <[email protected]>
Cc: uboot-imx <[email protected]>
|
|
Add new compatible string, used by some more up-to-date DTs.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Ye Li <[email protected]>
Cc: uboot-imx <[email protected]>
|
|
There is now multiple copies of CONFIG_MXC_USB_PORTSC in configs set to
PORT_PTS_UTMI | PORT_PTS_PTW, which is in fact the default register value
for MX6, MX7 and MX7ULP. Define the default value of CONFIG_MXC_USB_PORTSC
in the driver and use it in case CONFIG_MXC_USB_PORTSC is not defined in
config, to reduce the duplication.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Ye Li <[email protected]>
Cc: uboot-imx <[email protected]>
|
|
In case PHY support is enabled, use the generic EHCI PHY support
to start and stop the PHY.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Ye Li <[email protected]>
Cc: uboot-imx <[email protected]>
|
|
In case the platform uses DM, determine port number, which is
used as offset in USBMISC registers, from PHY node DT aliases,
just like Linux does.
Fixes: 4de51cc25b5 ("usb: ehci-mx6: Drop assignment of sequence number")
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Ye Li <[email protected]>
Cc: uboot-imx <[email protected]>
|
|
Instead of passing ad-hoc sequence number to usb_oc_config(), pass in
the USB MISC address itself. The USB MISC address comes from DT in DM
case, and from the old method using controller index in non-DM case.
Fixes: 4de51cc25b5 ("usb: ehci-mx6: Drop assignment of sequence number")
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Ye Li <[email protected]>
Cc: uboot-imx <[email protected]>
|
|
Split usb_power_config() per SoC and pass in USB PHY, USBNC and ANATOP
addresses instead of ad-hoc sequence numbers. This is only applicable
on legacy systems which do not implement proper PHY support. Once PHY
support is available, parts of this can be removed altogether and moved
to the PHY driver, similar to Linux phy-mxs-usb.c .
Fixes: 4de51cc25b5 ("usb: ehci-mx6: Drop assignment of sequence number")
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Ye Li <[email protected]>
Cc: uboot-imx <[email protected]>
|
|
Instead of passing ad-hoc index to USB PHY handling functions and then
try and figure out the PHY address, pass in the PHY address itself. For
DM case, this address comes easily from DT. For non-DM case, the previous
method is still present, however the non-DM case will soon be removed.
Fixes: 4de51cc25b5 ("usb: ehci-mx6: Drop assignment of sequence number")
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Ye Li <[email protected]>
Cc: uboot-imx <[email protected]>
|
|
In order to pass component addresses around easily instead of passing
ad-hoc sequence numbers, it is necessary to split ehci_mx6_common_init().
Make it so and call the separate functions instead.
Since board_ehci_hcd_init() makes no sense in DM case, do not call it
in DM case.
Fixes: 4de51cc25b5 ("usb: ehci-mx6: Drop assignment of sequence number")
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Ye Li <[email protected]>
Cc: uboot-imx <[email protected]>
|
|
In case DM and OF controler is enabled, but PHY support is disabled,
parse USB PHY and MISC component addresses from DT manually. Those
component addresses will be used in subsequent patches to access the
ANATOP, PHY and MISC registers matching the controller and thus get
rid of the ad-hoc controller sequence number mapping.
Fixes: 4de51cc25b5 ("usb: ehci-mx6: Drop assignment of sequence number")
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Ye Li <[email protected]>
Cc: uboot-imx <[email protected]>
|
|
Merge USBNC register layout structure into a single one, instead of
having three separate structures and a lot of ifdeffery. No functional
change.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Ye Li <[email protected]>
Cc: uboot-imx <[email protected]>
|
|
Add support for using DM clock framework to enable and disable all the
necessary clock for the USB controller.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Ye Li <[email protected]>
Cc: uboot-imx <[email protected]>
|
