| Age | Commit message (Collapse) | Author |
|---|
|
When u-boot enable CONFIG_SYS_BOOT_RAMDISK_HIGH, rootfs image relocated
from FIU address space to memory address before jump to kernel.
Since Arbel reserved memory from 0x00000000 to 0x06200000 for tip image,
and rootfs image may too large that cannot found a suitable location
before 128MB(0x8000000), so increase mapping size from 128MB to 192MB.
Signed-off-by: Jim Liu <[email protected]>
|
|
Add mem and console env information and modify the wrong earlycon env.
Signed-off-by: Jim Liu <[email protected]>
|
|
Remove not needed variables from environment.
- boot_scripts is not needed, the default value is just fine and
already includes boot.scr
- setup variable used to be executed from some bootscript, however
it's not required and there is no point on having this small helper
here
Signed-off-by: Francesco Dolcini <[email protected]>
|
|
In commit 51aaaf5e7975 ("board: toradex: imx: Remove not needed env variables")
the empty definition of fdt_fixup variable was removed, however this was
still referenced from the boot command leading to boot failures:
## Error: \"fdt_fixup\" not defined`
Fix this by removing "run fdt_fixup" from the boot command and instead
enable CONFIG_OF_ENV_SETUP in the defconfig that would achieve the same
but in a more robust way (it works fine even if the variable is not
defined).
Fixes: 51aaaf5e7975 ("board: toradex: imx: Remove not needed env variables")
Signed-off-by: Francesco Dolcini <[email protected]>
|
|
Support for Schneider Electric HMIBSC. Features:
- Qualcomm Snapdragon 410C SoC - APQ8016 (4xCortex A53, Adreno 306)
- 2GiB RAM
- 64GiB eMMC, SD slot
- WiFi and Bluetooth
- 2x Host, 1x Device USB port
- HDMI
- Discrete TPM2 chip over SPI
Features enabled in U-Boot:
- RAUC updates
- Environment protection
- USB based ethernet adaptors
Signed-off-by: Sumit Garg <[email protected]>
Signed-off-by: Caleb Connolly <[email protected]>
|
|
Janne Grunau <[email protected]> says:
This series contains a few misc config changes for Apple silicon
systems:
- switch from the deprecated distro boot scripts to standard boot
- allows EFI console resizing based on the video console size
- enables 16x32 bitmap fonts as Apple devices come with high DPI
displays
- enables 64-bit LBA addressing
|
|
Use standard boot instead of the distro boot scripts. Use
BOOTSTD_FULL instead of BOOTSTD_DEFAULTS for easier interactive use.
Signed-off-by: Janne Grunau <[email protected]>
Reviewed-by: Mark Kettenis <[email protected]>
Reviewed-by: Neal Gompa <[email protected]>
|
|
The display size querying in efi_console relies on this order. The
display should be the primary output device and should be used to
display more than 80x25 chars.
Reviewed-by: Mark Kettenis <[email protected]>
Reviewed-by: Neal Gompa <[email protected]>
Signed-off-by: Janne Grunau <[email protected]>
|
|
Use recently added ability to assign commands to buttons via env.
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
Drop the distro-boot scripts and use standard boot instead.
Inspired by:
'commit 7755dc58af7b ("rockchip: Move to standard boot")'
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-video
CI: https://source.denx.de/u-boot/custodians/u-boot-video/-/pipelines/20466
- simple_panel: support timing parsing from EDID
- dw_hdmi: fix gcc-14 compiler warnings
- dw_hdmi: support vendor PHY for HDMI
- rockchip: add Rockchip INNO HDMI PHY driver
- rockchip: RK3328 HDMI and VOP support
- evb-rk3328: enable vidconsole support
- Tegra DC and DSI improvements and Tegra 114 support
- add LG LG070WX3 MIPI DSI panel driver
- add Samsung LTL106HL02 MIPI DSI panel driver
- add Toshiba TC358768 RGB to DSI bridge support
- add basic support for the Parade DP501 transmitter
- Tegra 3 panel and bridge driver improvements
- simplefb: modernise DT parsing
- fdt_simplefb: Enumerate framebuffer info from video handoff
- preserve framebuffer if SPL is passing video hand-off
- fdt_support: allow reserving FB region without simplefb
|
|
Enable video console for Rockchip RK3328.
Signed-off-by: Jagan Teki <[email protected]>
|
|
Remove not needed variables from environment and include config files.
- setup variable used to be executed from some bootscript, however
it's not required and there is no point on having this small helper
here
- boot_file, kernel_file, ip_dyn variables are not used anywhere
- fdt_fixup variable is just set empty
- defargs, vidargs variables used to be used from some bootscript,
however there is no point on having it here and even old legacy
bootscript can work without them
- removed CONFIG_ENABLE_DDR_TRAINING_DEBUG, this is a leftover from
some copy/paste
On colibri imx6ull/imx7 NAND module, remove consoleblank=0, this is
already the Linux kernel default therefore useless.
Various Linux Kernel command line options removed are not-existing
left-over that applied to some old NXP i.MX downstream branch
Signed-off-by: Francesco Dolcini <[email protected]>
|
|
is selected
Remove amlogic/ path prefix in CFG_EXTRA_ENV_SETTINGS fdtfile when
using CONFIG_OF_UPSTREAM, otherwise amlogic/ is added twice.
Tested-by: Mattijs Korpershoek <[email protected]> # khadas-vim3_android
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Neil Armstrong <[email protected]>
|
|
Fix JetHub board sequence to read correct gpio for rescue button
Signed-off-by: Viacheslav Bocharov <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Neil Armstrong <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2024.07 cycle:
- This feature set includes a new board named sama7g54 Curiosity.
|
|
https://source.denx.de/u-boot/custodians/u-boot-socfpga into next
- A new driver in the misc to register setting from device tree. This
also provides user a clean interface and all register settings are
centralized in one place, device tree.
- Enable Agilex5 platform for Intel product. Changes, modification and
new files are created for board, dts, configs and makefile to create
the base for Agilex5.
Build-tested on SoC64 boards, boot tested on some of them.
|
|
This patch is to enable Agilex5 platform for Intel
product. Changes, modification and new files are
created for board, dts, configs and makefile to
create the base for Agilex5.
Signed-off-by: Jit Loon Lim <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
Move the environment into the board directory and convert it from a C
header to a text file. Sort the variables alphabetically.
No functional changes.
Signed-off-by: Leonard Anderweit <[email protected]>
Reviewed-by: Teresa Remmet <[email protected]>
Tested-by: Teresa Remmet <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-rockchip into next
Please pull the updates for rockchip platform:
- Add board: rk3588 Generic, Cool Pi CM5, Theobroma-Systems RK3588 Jaguar SBC,
Toybrick TB-RK3588X;
rk3588s Cool Pi 4B;
rk3566 Pine64 PineTab2;
- Add saradc v2 support;
- Add PMIC RK806 support;
- rk3588 disable force_jtag by default;
- Migrate to use IO-domain driver for all boards;
- Use common bss and stack addresses for rk33xx and rk35xx boards;
- Other updates for driver, config and dts;
|
|
Move ROCK Pi 4 specific board code from the shared evb_rk3399 target
into its own board target and update related defconfigs to use the new
TARGET_ROCKPI4_RK3399 option.
Signed-off-by: Jonas Karlman <[email protected]>
Reviewed-by: Christopher Obbard <[email protected]>
Reviewed-by: Peter Robinson <[email protected]>
|
|
TB-RK3588X board is a Rockchip Toybrick RK3588 based development board.
Specification:
Rockchip Rk3588 SoC
4x ARM Cortex-A76, 4x ARM Cortex-A55
8/16GB Memory LPDDR4x
Mali G610MC4 GPU
2× MIPI-CSI0 Connector
1x 2Lanes PCIe3.0 Connector
1x SATA3.0 Connector
32GB eMMC Module
2x USB 2.0, 2x USB 3.0
1x HDMI Output, 1x HDMI Input
2x Ethernet Port
Functions work normally:
[1] USB2.0 Host
[2] Ethernet0 with PHY RTL8211F
More information can be obtained from the following websites:
[1] https://t.rock-chips.com/en/wiki/EN/tb-rk3588x_en/index.html
[2] http://t.rock-chips.com/
Kernel commits:
8ffe365f8dc7 ("arm64: dts: rockchip: Add devicetree support for TB-RK3588X board")
7140387ff49d ("dt-bindings: arm: rockchip: Add Toybrick TB-RK3588X")
Reviewed-by: Weizhao Ouyang <[email protected]>
Signed-off-by: Elon Zhang <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
This architecture and related board are unmaintained currently and have
been for a long time. Remove them.
Signed-off-by: Tom Rini <[email protected]>
|
|
Introduce the initial configs needed to support the am62px SoC family
Signed-off-by: Bryan Brattlof <[email protected]>
|
|
Add default configuration for nand-flash to boot the linux kernel.
Add default configuration for qspi-flash to boot the linux kernel.
Add default configuration for sd-card to boot the linux kernel.
Configs are synced with savedefconfig.
Signed-off-by: Mihai Sain <[email protected]>
|
|
JAGUAR is a Single-Board Computer (SBC) based around the rk3588 SoC and
is targeting Autonomous Mobile Robots (AMR).
It features:
* LPDDR4X (up to 16GB)
* 1Gbps Ethernet on RJ45 connector (KSZ9031 or KSZ9131)
* PCIe 3.0 4-lane on M.2 M-key connector
* PCIe 2.1 1-lane on M.2 E-key
* USB 2.0 on M.2 E-key
* 2x USB3 OTG type-c ports with DP Alt-Mode
* USB2 host port
* HDMI output
* 2x camera connectors, each exposing:
* 2-lane MIPI-CSI
* 1v2, 1v8, 2v8 power rails
* I2C bus
* GPIOs
* PPS input
* CAN
* RS485 UART
* FAN connector
* SD card slot
* eMMC (up to 256GB)
* RTC backup battery
* Companion microcontroller
* ISL1208 RTC emulation
* AMC6821 PWM emulation
* On/off buzzer control
* Secure Element
* 80-pin Mezzanine connector for daughterboards:
* GPIOs
* 1Gbps Ethernet
* PCIe 2.1 1-lane
* 2x 2-lane MIPI-CSI
* ADC channel
* I2C bus
* PWM
* UART
* SPI
* SDIO
* CAN
* I2S
* 1v8, 3v3, 5v0, dc-in (12-24V) power rails
The Device Tree comes from next-20240110 Linux kernel.
Cc: Quentin Schulz <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
Signed-off-by: Quentin Schulz <[email protected]>
|
|
hardware.h is only defining macros which are "wrappers" around writel().
writel() is however not available in hardware.h, <asm/io.h> needs to be
included. This means in order to use the wrappers in hardware.h, one
also needs to include the <asm/io.h> header.
However, this cannot be done currently because hardware.h is included in
include/configs files, which are implicitly included by every code file
by default, which makes the compilation of arch/arm/cpu/armv8/u-boot.lds
fail because ALIGN (the ARM assembly directive) got redefined by some
of the include files coming from <asm.io.h>.
Because nothing in the include/configs file actually use hardware.h,
let's remove the inclusion of hardware.h from the include/configs files
and explicitly add it wherever it is required.
This prepares for the next commit where <asm/io.h> will be included in
hardware.h.
Cc: Quentin Schulz <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
Signed-off-by: Quentin Schulz <[email protected]>
|
|
Distro boot scripts are deprecated. Use standard boot instead.
Signed-off-by: Nam Cao <[email protected]>
Reviewed-by: Leo Yu-Chi Liang <[email protected]>
|
|
Prepare v2024.04-rc4
|
|
Add support for PHYTEC phyCORE-AM64x SoM.
Supported features:
- 2GB DDR4 RAM
- eMMC Flash
- external uSD
- OSPI NOR Flash
- debug UART
Product page SoM: https://www.phytec.com/product/phycore-am64x
Device trees were taken from Linux v6.8-rc2.
Signed-off-by: Wadim Egorov <[email protected]>
Reviewed-by: Dhruva Gole <[email protected]>
|
|
Add board files for J784S4 EVM.
SYS_DISABLE_DCACHE_OPS is selected in the Kconfig because
J784S4/AM69 are a coherent architecture at A72 level by
MSMC support.
Signed-off-by: Hari Nagalla <[email protected]>
Signed-off-by: Dasnavis Sabiya <[email protected]>
Signed-off-by: Apurva Nandan <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Tested-by: Marcel Ziswiler <[email protected]> # AM69-SK
|
|
Rename rmobile.h to renesas.h because all the chips are made
by Renesas, while only a subset of them is from the R-Mobile
line.
Use the following command to perform the rename:
"
$ git grep -l 'include.*rmobile.h' | \
xargs -I {} sed -i '/include.*rmobile.h/ [email protected]@renesas.h@g' {}
"
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Paul Barker <[email protected]>
|
|
The FWU Multi Bank Update feature allows the platform to boot the
firmware images from one of the partitions(banks).
On the Developerbox, SCP-firmware running on the SCB(Cortex-M3)
passes the value of the boot index on the NOR flash.
Add a function to read the boot index value from the NOR flash.
Signed-off-by: Masahisa Kojima <[email protected]>
|
|
Historically, Qualcomm boards have relied on heavy hardcoding in U-Boot,
in many cases to the specific SoC but also to the board itself (e.g.
memory map). This has been largely resolved by modernising the Qualcomm
drivers in U-Boot, however the board code still largely follows this
model.
This patch removes the board specific memory maps and duplicated board
init code, replacing it with generic init code.
The memory map is now built at runtime based on data read from DT, this
allows for the memory map to be provided without having to recompile
U-Boot. Support is also added for booting with appended DTBs, so that
the first-stage bootloader can populate the memory map for us.
The sdm845 specific init code is dropped entirely, it set an environment
variable depending on if a button was pressed, but this variable wasn't
used in U-Boot, and could be written to use the button command instead.
The KASLR detection is also dropped as with appended dtb, the kaslr seed
can be read directly from the DTB passed to U-Boot.
A new qcom_defconfig is added, with the aim of providing a generic
U-Boot configuration that will work on as many Qualcomm boards as
possible. It replaces the defconfig files for the Dragonboard 845c,
Galaxy S9, and QCS404 EVB. For now the db410c and 820c are excluded as
they still have some board code left.
Similarly, the config headers for db845c, starqltechn, and qcs404-evb
are replaced by a single qcom header.
The previously db410c-specific board_usb_init() function is made to be
generic and is added to mach-snapdragon. While we lack proper modelling
for USB configuration, using a well-known named pinctrl state is a
reasonably generic middleground, and works using upstream DT. This
function will do nothing unless the USB node has a pinctrl state named
"device", in which case it will be set when entering USB peripheral
mode.
Reviewed-by: Neil Armstrong <[email protected]>
Reviewed-by: Sumit Garg <[email protected]>
Tested-by: Sumit Garg <[email protected]> #qcs404
Signed-off-by: Caleb Connolly <[email protected]>
|
|
Now that we support having CONFIG_SYS_CONFIG_NAME be unset to indicate a
lack of board.h file, unset this on the hc2910-2aghd05 platform and remove
the otherwise empty file.
Signed-off-by: Tom Rini <[email protected]>
|
|
Now that we support having CONFIG_SYS_CONFIG_NAME be unset to indicate a
lack of board.h file, unset this on the slimbootloader platform and remove
the otherwise empty file.
Signed-off-by: Tom Rini <[email protected]>
|
|
Now that we support having CONFIG_SYS_CONFIG_NAME be unset to indicate a
lack of board.h file, unset this on the qemu-x86* platforms and remove
the otherwise empty file.
Signed-off-by: Tom Rini <[email protected]>
|
|
Now that we support having CONFIG_SYS_CONFIG_NAME be unset to indicate a
lack of board.h file, unset this on the minnowmax platform and remove
the otherwise empty file.
Signed-off-by: Tom Rini <[email protected]>
|
|
Now that we support having CONFIG_SYS_CONFIG_NAME be unset to indicate a
lack of board.h file, unset this on the galileo platform and remove
the otherwise empty file.
Signed-off-by: Tom Rini <[email protected]>
|
|
Now that we support having CONFIG_SYS_CONFIG_NAME be unset to indicate a
lack of board.h file, unset this on the efi-x86_payload* platforms and remove
the otherwise empty file.
Signed-off-by: Tom Rini <[email protected]>
|
|
Now that we support having CONFIG_SYS_CONFIG_NAME be unset to indicate a
lack of board.h file, unset this on the efi-x86_app* platforms and remove
the otherwise empty file.
Signed-off-by: Tom Rini <[email protected]>
|
|
Now that we support having CONFIG_SYS_CONFIG_NAME be unset to indicate a
lack of board.h file, unset this on the edison platform and remove
the otherwise empty file.
Acked-by: Andy Shevchenko <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Now that we support having CONFIG_SYS_CONFIG_NAME be unset to indicate a
lack of board.h file, unset this on the crownbay platform and remove
the otherwise empty file.
Signed-off-by: Tom Rini <[email protected]>
|
|
Now that we support having CONFIG_SYS_CONFIG_NAME be unset to indicate a
lack of board.h file, unset this on the cougarcanyon2 platform and remove
the otherwise empty file.
Signed-off-by: Tom Rini <[email protected]>
|
|
Now that we support having CONFIG_SYS_CONFIG_NAME be unset to indicate a
lack of board.h file, unset this on the cherryhill platform and remove
the otherwise empty file.
Signed-off-by: Tom Rini <[email protected]>
|
|
Now that we support having CONFIG_SYS_CONFIG_NAME be unset to indicate a
lack of board.h file, unset this on the bayleybay platform and remove
the otherwise empty file.
Signed-off-by: Tom Rini <[email protected]>
|
|
Now that we support having CONFIG_SYS_CONFIG_NAME be unset to indicate a
lack of board.h file, unset this on the coreboot platform and remove
the otherwise empty file.
Signed-off-by: Tom Rini <[email protected]>
|
|
Now that we support having CONFIG_SYS_CONFIG_NAME be unset to indicate a
lack of board.h file, unset this on the xilinx_mbv platforms and remove
the otherwise empty file.
Acked-by: Michal Simek <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Add support for booting the imxrt1050-evk from spi.
Add imximage config and the ability for SPL to boot from NOR.
Enable binman in Kconfig and device tree for imxrt* as it is used to
prepend fspi_header.bin to SPL and u-boot.img.
Signed-off-by: Jesse Taube <[email protected]>
|
|
|
