| Age | Commit message (Collapse) | Author |
|---|
|
Remove 'fdt_high' and 'initrd_high' environment variables (set to 0xFFFFFFFF)
from default environment which prevents relocation of FDT and initrd.
Rely on 'bootm_size' value instead to safely relocate kernel, device tree and
initrd.
Signed-off-by: Igor Opaniuk <[email protected]>
Reviewed-by: Oleksandr Suvorov <[email protected]>
|
|
Remove 'fdt_high' and 'initrd_high' environment variables (set to 0xFFFFFFFF)
from default environment which prevents relocation of FDT and initrd.
Rely on 'bootm_size' value instead to safely relocate kernel, device tree and
initrd.
Signed-off-by: Igor Opaniuk <[email protected]>
Reviewed-by: Oleksandr Suvorov <[email protected]>
|
|
Remove 'fdt_high' and 'initrd_high' environment variables (set to 0xFFFFFFFF)
from default environment which prevents relocation of FDT and initrd.
Rely on 'bootm_size' value instead to safely relocate kernel, device tree and
initrd.
Signed-off-by: Igor Opaniuk <[email protected]>
Reviewed-by: Oleksandr Suvorov <[email protected]>
|
|
Remove 'fdt_high' and 'initrd_high' environment variables (set to 0xFFFFFFFF)
from default environment which prevents relocation of FDT and initrd.
Rely on 'bootm_size' value instead to safely relocate kernel, device tree and
initrd.
Signed-off-by: Igor Opaniuk <[email protected]>
Reviewed-by: Oleksandr Suvorov <[email protected]>
|
|
Remove 'fdt_high' and 'initrd_high' environment variables (set to 0xFFFFFFFF)
from default environment which prevents relocation of FDT and initrd.
Rely on 'bootm_size' value instead to safely relocate kernel, device tree and
initrd.
Signed-off-by: Igor Opaniuk <[email protected]>
Reviewed-by: Oleksandr Suvorov <[email protected]>
|
|
Add nfsboot wrapper to env to boot Linux kernel from TFTP/NFS.
Signed-off-by: Igor Opaniuk <[email protected]>
Reviewed-by: Oleksandr Suvorov <[email protected]>
|
|
Fixes compilation for WRU4 board.
Signed-off-by: Michael Krummsdorf <[email protected]>
|
|
Add Ethernet support using DM_ETH.
Signed-off-by: Fabio Estevam <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
|
|
CONFIG_FEC_MXC is supported in Kconfig, so it is preferred to
move it to defconfig file.
Signed-off-by: Fabio Estevam <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
|
|
Activate ARCH_SUPPORT_TFABOOT and replace the arch stm32mp
specific config CONFIG_STM32MP1_TRUSTED by the generic CONFIG_TFABOOT
introduced by the commit 535d76a12150 ("armv8: layerscape: Add TFABOOT
support").
This config CONFIG_TFABOOT is activated for the trusted boot chain,
when U-Boot is loaded by TF-A.
Signed-off-by: Patrick Delaunay <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
|
Unify the location of DT selection into board_late_init instead of
split between detection and static configuration paths.
Signed-off-by: Joel Johnson <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Enable distro bootcmd support for additional SATA ports if enabled.
Signed-off-by: Joel Johnson <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Include attempting to boot from SCSI (SATA) devices within generated
board distro bootcmd environment. The reasoning for boot ordering is
that MMC and USB are external and removable, while when a case is in
use, replacing M.2 or mSATA drives requires disassembly. Therefore,
to boot SCSI, [bootable] external media must be removed. If SCSI were
placed before MMC or USB, then removing a bootable SCSI drive to
enable MMC or USB booting would be more difficult.
Signed-off-by: Joel Johnson <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Support for sata devices via the scsi command is available and already
enabled by default for the Clearfog Base and Pro. This change adds scsi
to the list of boot targets used by distro-boot.
Signed-off-by: Josua Mayer <[email protected]>
Cc: Stefan Roese <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Pull in changes that have been pending in our 'next' branch. This
includes:
- A large number of CI improvements including moving to gcc-9.2 for all
platforms.
- amlogic, xilinx, stm32, TI SoC updates
- USB and i2c subsystem updtaes
- Re-sync Kbuild/etc logic with v4.19 of the Linux kernel.
- RSA key handling improvements
|
|
This patch ajust CONFIG_SYS_MEMTEST_END for vcoreiii-based systems to
avoid overwriting the relocated u-boot. The former setting was too
agressive with networking etc. enabled on some platforms.
Reviewed-by: Alexandre Belloni <[email protected]>
Reviewed-by: Horatiu Vultur <[email protected]>
Signed-off-by: Lars Povlsen <[email protected]>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2020.07
common:
- Align ENV_FAT_INTERFACE
- Fix MAC address source print log
- Improve based autodetection code
xilinx:
- Enable netconsole
Microblaze:
- Setup default ENV_OFFSET/ENV_SECT_SIZE
Zynq:
- Multiple DT updates/fixes
- Use DEVICE_TREE environment variable for DTB selection
- Switch to single zynq configuration
- Enable NOR flash via DM
- Minor SPL print removal
- Enable i2c mux driver
ZynqMP:
- Print multiboot register
- Enable cache commands in mini mtest
- Multiple DT updates/fixes
- Fix firmware probing when driver is not enabled
- Specify 3rd backup RAM boot mode in SPL
- Add SPL support for zcu102 v1.1 and zcu111 revA
- Redesign debug uart enabling and psu_init delay
- Enable full u-boot run from EL3
- Enable u-boot.itb generation without ATF with U-Boot in EL3
Versal:
- Enable distro default
- Enable others SPI flashes
- Enable systems without DDR
Drivers:
- Gem:
- Flush memory after freeing
- Handle mdio bus separately
- Watchdog:
- Get rid of unused global data pointer
- Enable window watchdog timer
- Serial:
- Change reinitialization logic in zynq serial driver
Signed-off-by: Tom Rini <[email protected]>
|
|
Overlapped with fdt_addr*, thus corrupted the latter when using both.
Signed-off-by: Jan Kiszka <[email protected]>
|
|
With multi defconfig NOR flash information about NOR should be taken from
DT that's why there is no reason to specify address and sizes via fixed
config.
Signed-off-by: Michal Simek <[email protected]>
|
|
With multi defconfig targeting several board configurations bug report like
below is so verbose.
Flash: ## Unknown flash on Bank 1 - Size = 0x00000000 = 0 MB
0 Bytes
Do not report that message and simply say "Flash: 0 Bytes" because most of
Zynq boards are using different type of flashes than NOR.
Signed-off-by: Michal Simek <[email protected]>
|
|
- Add support for Jetson Nano, plus miscellaneous other fixes found
during Nano bringup.
- Add Igor's update_uboot wrapper patches.
|
|
The Jetson Nano Developer Kit is a Tegra X1-based development board. It
is similar to Jetson TX1 but it is not pin compatible. It features 4GB
of LPDDR4, a SPI NOR flash for early boot firmware and an SD card slot
used for storage.
HDMI 2.0 or DP 1.2 are available for display, four USB ports (3 USB 2.0
and 1 USB 3.0) can be used to attach a variety of peripherals and a PCI
Ethernet controller provides onboard network connectivity. NVMe support
has also been added. Env save is at the end of QSPI (4MB-8K).
A 40-pin header on the board can be used to extend the capabilities and
exposed interfaces of the Jetson Nano.
Signed-off-by: Thierry Reding <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
Tested-by: Peter Robinson <[email protected]>
|
|
The L4T kernel is 32MB+, and can overwrite the ramdisk/fdt loaded
from extlinux.conf. Adjust the load addresses to fix this for now.
Using the calculated_env addresses table from T186 U-Boot is a
better fix, but it isn't working correctly on T210 U-Boot right now,
so this will do until I can fix it.
Signed-off-by: Tom Warren <[email protected]>
|
|
Add universal update_uboot wrapper that helps to update
U-Boot image on internal storage.
Create an proper tegra image:
$ cbootimage -s tegra30 colibri_t30.img.cfg colibri_t30.img
Flash in U-boot shell:
> tftpboot ${loadaddr} ${board_name}/${board_name}.img
> run update_uboot
Signed-off-by: Igor Opaniuk <[email protected]>
Reviewed-by: Oleksandr Suvorov <[email protected]>
|
|
Add universal update_uboot wrapper that helps to update
U-Boot image on internal storage(NAND).
Create an proper tegra image:
$ cbootimage -s tegra20 colibri_t20-512-v12-nand.img.cfg colibri_t20.img
Flash in U-boot shell:
> tftpboot ${loadaddr} ${board_name}/${board_name}.img
> run update_uboot
Signed-off-by: Igor Opaniuk <[email protected]>
Reviewed-by: Oleksandr Suvorov <[email protected]>
|
|
Add universal update_uboot wrapper that helps to update
U-Boot image on internal storage.
Create an proper tegra image:
$ cbootimage -s tegra30 apalis_t30.img.cfg apalis_t30.img
Flash in U-boot shell:
> tftpboot ${loadaddr} ${board_name}/${board_name}.img
> run update_uboot
Signed-off-by: Igor Opaniuk <[email protected]>
Reviewed-by: Oleksandr Suvorov <[email protected]>
|
|
Add universal update_uboot wrapper that helps to update
U-Boot image on internal storage.
Create an proper tegra image:
$ cbootimage -s tegra124 apalis-tk1.img.cfg apalis-tk1.img
Flash in U-boot shell:
> tftpboot ${loadaddr} ${board_name}/${board_name}.img
> run update_uboot
Signed-off-by: Igor Opaniuk <[email protected]>
Reviewed-by: Oleksandr Suvorov <[email protected]>
|
|
Enable config options and console setting to respective
rk3399 board for HDMI output.
Boards supported and tested on this patch are:
- NanoPc T4
- NanoPi M4
- NanoPi Neo4
- ROC-RK3399-PC
- Rock960
Cc: Manivannan Sadhasivam <[email protected]>
Signed-off-by: Jagan Teki <[email protected]>
Tested-by: Peter Robinson <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-04-rc5
This series fixes:
* UEFI Python tests CONFIG_OF_CONTROL=y.
* int to pointer cast warning for cmd/efidebug.c
* memory reservation even if fdt node is disabled
Now that the Python test is fixed reintroduce the reverted patch for
vexpress_ca9x4 to enable EFI_LOADER and define the dtb file name.
|
|
Change to use SOCFPGA_PHYS_OCRAM_SIZE macro for onchip RAM size.
Signed-off-by: Ley Foon Tan <[email protected]>
|
|
MC_INIT and BOOT command currently access spi-nor flash memory directly.
As per spi-mem framework, flash memory access via absolute addresses is
no more possible. Use flash APIs to access memory instead of directly
using it.
Signed-off-by: Kuldeep Singh <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
Adjust environment kernel_addr_r from 0x96000000 to 0x92000000
to fix a bug that failed to boot kernel for ls1012afrwy with 512MiB RAM,
=> tftpboot $kernel_addr_r Image (Image size is 36 MiB)
TFTP error: trying to overwrite reserved memory...
Signed-off-by: Biwen Li <[email protected]>
Signed-off-by: Priyanka Jain <[email protected]>
|
|
This patch appends othbootargs to bootargs for LS1021ATWR board.
Signed-off-by: Alison Wang <[email protected]>
Signed-off-by: Priyanka Jain <[email protected]>
|
|
This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1046A
Signed-off-by: Biwen Li <[email protected]>
Signed-off-by: Priyanka Jain <[email protected]>
|
|
This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1043A
Signed-off-by: Biwen Li <[email protected]>
Signed-off-by: Priyanka Jain <[email protected]>
|
|
Fix wrong environment variable of board for ls1012afrwy
Signed-off-by: Biwen Li <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
Move the environment variables from command head file to
ls1028ardb specific head file so that they will not mess
up with ls1028aqds board.
Also updated some variable slightly.
There is no function change by this patch.
Signed-off-by: Yuantian Tang <[email protected]>
Signed-off-by: Priyanka Jain <[email protected]>
|
|
Add sd and emmc bootcmd environments to facilitate
the boot process.
Signed-off-by: Yuantian Tang <[email protected]>
Signed-off-by: Priyanka Jain <[email protected]>
|
|
Add support of distro boot for ls2080aqds
Signed-off-by: Biwen Li <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
Add support of distro boot for ls1088aqds
Signed-off-by: Biwen Li <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
The old load address of itb will overwrite uboots reserved memory
on ls1012afrwy with 512 MiB ram
Signed-off-by: Biwen Li <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
Add dhcp in supported boot_targets for lx2160.
Signed-off-by: Meenakshi Aggarwal <[email protected]>
Signed-off-by: Priyanka Jain <[email protected]>
|
|
Add DHCP boot target device to enable command bootcmd_dhcp.
Signed-off-by: Yuantian Tang <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
Set VID to 800 mV for Rev1 and set VID as per switch settings
for Rev2.
Signed-off-by: Meenakshi Aggarwal <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
Update the secure boot headers offsets of Kernel and other
firmware images for SD and XSPI boot sources used by
esbc_validate command.
Signed-off-by: Priyanka Singh <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
Add emmc in supported boot_targets and
Add bootcmd environment variable for emmc boot.
Signed-off-by: Meenakshi Aggarwal <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
Setting fdt_high and initrd_high to 0xffffffffffffffff leads to
various difficulty to resolve bugs.
Remove them and use bootm_size instead to safely contain a kernel,
device tree and initrd for relocation.
Signed-off-by: Yuantian Tang <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
Setting fdt_high and initrd_high to 0xffffffffffffffff leads to
various difficulty to resolve bugs.
Remove them and use bootm_size instead to safely contain a kernel,
device tree and initrd for relocation.
Signed-off-by: Yuantian Tang <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
This patch sets CONFIG_SYS_BOOTMAPSZ to the amount of memory available
to safely contain a kernel, device tree and initrd for relocation. The
way to set fdt_high as 0xffffffff to disable device tree relocation is
removed.
Signed-off-by: Alison Wang <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
