summaryrefslogtreecommitdiff
path: root/include/configs
AgeCommit message (Collapse)Author
2012-09-01ARM: add Raspberry Pi model B board, using BCM2835 SoCStephen Warren
The Raspberry Pi model B uses the BCM2835 SoC, has 256MB of RAM, contains an SMSC 9512 USB LAN/Hub chip, and various IO connectors. For more details, see http://www.raspberrypi.org/. Various portions (cache enable, MACH_TYPE setup, RAM size limit, stack relocation to top of RAM) extracted from work by: Oleksandr Tymoshenko <[email protected]>. GPIO driver enablement by Vikram Narayanan <[email protected]>. Signed-off-by: Stephen Warren <[email protected]> Acked-by: Tom Rini <[email protected]>
2012-09-01u8500: Separating mmc config parameters from driverJohn Rigby
Configuration in vexpress and u8500.v1 is different from what is needed in u8500.v2. As such, card configuration specifics need to reside in the board file rather than the driver. Signed-off-by: John Rigby <[email protected]> Signed-off-by: Mathieu Poirier <[email protected]> Signed-off-by: Tom Rini <[email protected]>
2012-09-01snowball: applying power to LAN and GBF controllersMathieu J. Poirier
LAN and GBF need to be powered explicitely, doing so with interface to AB8500 companion chip. Signed-off-by: Mathieu Poirier <[email protected]> Signed-off-by: John Rigby <[email protected]>
2012-09-01snowball: Adding architecture dependent initialisationMathieu J. Poirier
Enabling timers and clocks in PRCMU and cleaning up mailbox. Signed-off-by: Mathieu Poirier <[email protected]> Signed-off-by: John Rigby <[email protected]>
2012-09-01snowball: Add support for ux500 based snowball boardMathieu J. Poirier
Signed-off-by: Mathieu Poirier <[email protected]> Signed-off-by: John Rigby <[email protected]> Acked-by: Tom Rini <[email protected]> Acked-by: Linus Walleij <[email protected]> Conflicts: drivers/gpio/Makefile
2012-09-01da8xx/hawkboard: Add support for ohci host controllerSughosh Ganu
Also enable the ohci port on hawkboard. These additions result in an increased u-boot size -- adjust the same accordingly in the board's config. Move the usb header for da8xx platforms under arch-davinci. Signed-off-by: Sughosh Ganu <[email protected]>
2012-09-01omap4/5/am33xx: Make lowlevel_init available to all armv7 platformsTom Rini
Make the lowlevel_init function that these platforms have which just sets up the stack and calls a C function available to all armv7 platforms. As part of this we change some of the macros that are used to be more clear. Previously (except for am335x evm) we had been setting CONFIG_SYS_INIT_SP_ADDR to a series of new defines that are equivalent to simply referencing NON_SECURE_SRAM_END. On am335x evm we should have been doing this initially and do now. Cc: Sricharan R <[email protected]> Tested-by: Allen Martin <[email protected]> Signed-off-by: Tom Rini <[email protected]>
2012-09-01am335x evm: Enable support for spi0Tom Rini
Signed-off-by: Tom Rini <[email protected]>
2012-09-01sc_sps_1: Adjust board config to use 'mxs' SoC codeOtavio Salvador
Fix build failure due the move of mx28 code to 'mxs' SoC. Signed-off-by: Otavio Salvador <[email protected]> Acked-by: Stefano Babic <[email protected]>
2012-09-01MX28: Add SchulerControl SC_SPS_1 platformMarek Vasut
This i.MX28 platform supports the following: * 2x FEC ethernet * USB on USBH0 * I2C EEPROM * SPI NVRAM * LEDs Signed-off-by: Marek Vasut <[email protected]>
2012-09-01vision2: do not overwrite the consoleFabio Estevam
On this board, the console is always set to the serial line. Do not allow to overwrite it when video is enabled. Signed-off-by: Fabio Estevam <[email protected]>
2012-09-01mx51evk: do not overwrite the consoleFabio Estevam
On this board, the console is always set to the serial line. Do not allow to overwrite it when video is enabled. Signed-off-by: Fabio Estevam <[email protected]>
2012-09-01MX5: mx53loco: do not overwrite the consoleStefano Babic
On this board, the console is always set to the serial line. Do not allow to overwrite it when video is enabled. Signed-off-by: Stefano Babic <[email protected]> CC: Fabio Estevam <[email protected]> Tested-by: Fabio Estevam <[email protected]>
2012-09-01mxs: reorganize source directory for easy sharing of code in i.MXS SoCsOtavio Salvador
Most code can be shared between i.MX23 and i.MX28 as both are from i.MXS family; this source directory structure makes easy to share code among them. Signed-off-by: Otavio Salvador <[email protected]> Acked-by: Stefano Babic <[email protected]>
2012-09-01mx28evk: Turn on cachesFabio Estevam
Turn on data and instruction caches. Signed-off-by: Fabio Estevam <[email protected]>
2012-09-01Add support for Bluegiga APX4 Development KitVeli-Pekka Peltola
This adds support for Bluegiga APX4 Development Kit. It is built around Freescale i.MX28. Currently supported features are: ethernet, I2C, MMC, RTC and USB. APX4 has only one ethernet port. Signed-off-by: Veli-Pekka Peltola <[email protected]> Signed-off-by: Lauri Hintsala <[email protected]> Cc: Stefano Babic <[email protected]>
2012-09-01at91: Add support for taskit AT91SAM9G20 boards.Markus Hubig
This adds support for the AT91SAM9G20 boards by taskit GmbH. Both boards, Stamp9G20 and PortuxG20, are integrated in one file. PortuxG20 is basically a SBC built around the Stamp9G20. Signed-off-by: Markus Hubig <[email protected]> Cc: Andreas Bießmann <[email protected]> Signed-off-by: Andreas Bießmann <[email protected]>
2012-09-01arm : Atmel : add at91sam9x5ek board supportBo Shen
Add at91sam9x5ek board support, this board support the following SoCs AT91SAM9G15, AT91SAM9G25, AT91SAM9G35, AT91SAM9X25, AT91SAM9X35 Using at91sam9x5ek_nandflash to configure for the board Now only supports NAND with software ECC boot up Signed-off-by: Bo Shen <[email protected]> [move MAINTAINERS entry to right place] Signed-off-by: Andreas Bießmann <[email protected]>
2012-09-01am335x_evm: enable SMSC PHY driverIlya Yanok
Beaglebone uses SMSC PHY which works incorrectly with generic PHY driver so enable SMSC PHY driver to fix networking problems on Beaglebone. Signed-off-by: Ilya Yanok <[email protected]>
2012-09-01dm: Move OMAP GPIO driver to drivers/gpio/Marek Vasut
Signed-off-by: Marek Vasut <[email protected]> Cc: Wolfgang Denk <[email protected]> Cc: Albert Aribaud <[email protected]> Cc: U-Boot DM <[email protected]> Cc: Tom Rini <[email protected]> Acked-by: Tom Rini <[email protected]> Signed-off-by: Tom Rini <[email protected]>
2012-09-01dm: Select CONFIG_SPL_GPIO_SUPPORT on OMAPMarek Vasut
This fixes the breakage with SPL on most OMAP boards after the GPIO driver was moved. Signed-off-by: Marek Vasut <[email protected]> Cc: Wolfgang Denk <[email protected]> Cc: Albert Aribaud <[email protected]> Cc: U-Boot DM <[email protected]> Cc: Tom Rini <[email protected]> Acked-by: Tom Rini <[email protected]> Signed-off-by: Tom Rini <[email protected]>
2012-09-01am33xx evm: Add CONFIG_CMD_EEPROM and relatedTom Rini
am33xx boards have at least one eeprom and in the case of beaglebones with capes, more. Signed-off-by: Tom Rini <[email protected]>
2012-09-01am335x_evm: Update config for common usageTom Rini
- Add default commands - Add HUSH parser - Make environment, malloc areas larger - Add ATAGS and OF_LIBFDT - Add defaults to boot ramdisk and MMC, use uEnv.txt Signed-off-by: Tom Rini <[email protected]>
2012-09-01OMAP3: igep00x0: add SPL support for IGEP-based boardsJavier Martinez Canillas
This patch adds SPL support for IGEP-based boards. Tested on an IGEPv2 Rev.C board with Micron NAND Flash memory. Signed-off-by: Javier Martinez Canillas <[email protected]>
2012-09-01OMAP3: igep00x0: Add config option to choose flash storage memoryJavier Martinez Canillas
IGEP-based boards can have two different flash memories, a OneNAND or a NAND device. Add a configuration option for to choose which memory to use. Signed-off-by: Javier Martinez Canillas <[email protected]> Acked-by: Enric Balletbo i Serra <[email protected]>
2012-09-01am335x_evm: CPSW supportChandan Nath
This patch adds board-specific initialization for CPSW on TI AM335X based boards. Tested on BeagleBone. Signed-off-by: Chandan Nath <[email protected]> [Ilya: split board-specific part into separate patch] Signed-off-by: Ilya Yanok <[email protected]>
2012-09-01omap: am335x_evm: enable i2c1 channelSteve Sakoman
This patch sets up pinmux, enables fclk, and defines CONFIG_I2C_MULTI_BUS Signed-off-by: Steve Sakoman <[email protected]>
2012-09-01beagle: fix termination of buddy env settingPeter Meerwald
Signed-off-by: Peter Meerwald <[email protected]>
2012-09-01igep00x0: default mmcrootfstype to EXT4Javier Martinez Canillas
omap2plus_defconfig now has built-in compile support for EXT4 enabled by default now. So, we can use EXT4 as the default root file system type for MMC. Signed-off-by: Javier Martinez Canillas <[email protected]> Acked-by: Enric Balletbo i Serra <[email protected]>
2012-09-01igep00x0: default to OMAP-specific serial driverJavier Martinez Canillas
An OMAP specific serial driver was merged on the Linux kenel a long time ago. So, it makes sense to default the console name to OMAP ttyO instead of the generic ttyS naming. Signed-off-by: Javier Martinez Canillas <[email protected]> Acked-by: Enric Balletbo i Serra <[email protected]>
2012-09-01da850/omap-l138: add support for direct NOR boot modeLad, Prabhakar
This patch adds support for direct NOR boot mode on da850/omap-l138. Added da850evm_direct_nor entry in boards.cfg to allow to build targets. Tested-by: Christian Riesch <[email protected]> Signed-off-by: Lad, Prabhakar <[email protected]> Signed-off-by: Rajashekhara, Sudhakar <[email protected]> Signed-off-by: Hadli, Manjunath <[email protected]>
2012-09-01da850/omap-l138: Add support for NAND SPLLad, Prabhakar
This patch adds configuration required for NAND SP on DA850/OMAP-L138. Tested-by: Christian Riesch <[email protected]> Signed-off-by: Lad, Prabhakar <[email protected]> Signed-off-by: Rajashekhara, Sudhakar <[email protected]> Signed-off-by: Hadli, Manjunath <[email protected]>
2012-09-01da850/omap-l138: Add support to read u-boot image from MMC/SDLad, Prabhakar
DA850/OMAP-L138 does not support strict MMC/SD boot mode. SPL will be in SPI flash and U-Boot image will be in MMC/SD card. SPL will do the low level initialization and then loads the u-boot image from MMC/SD card. Define CONFIG_SPL_MMC_LOAD macro in the DA850/OMAP-L138 configuration file to enable this feature. Tested-by: Christian Riesch <[email protected]> Signed-off-by: Lad, Prabhakar <[email protected]> Signed-off-by: Rajashekhara, Sudhakar <[email protected]> Signed-off-by: Hadli, Manjunath <[email protected]>
2012-09-01da850/omap-l138: Define SPI specific configs for SPL only when SPI is usedLad, Prabhakar
define SPI specific configs for SPL only when CONFIG_USE_SPIFLASH config is defined Tested-by: Christian Riesch <[email protected]> Signed-off-by: Lad, Prabhakar <[email protected]> Signed-off-by: Rajashekhara, Sudhakar <[email protected]> Signed-off-by: Hadli, Manjunath <[email protected]>
2012-09-01da850/omap-l138: Make MMC and NOR support mutually exclusiveRajashekhara, Sudhakar
On Logic PD Rev.3 DA850/OMAP-L138 EVM, NOR and MMC/SD cannot work together. This patch enables the MMC/SD support only when NOR support is disabled. NOR Flash identification works even without this patch, but erase and write will have issues. Tested-by: Christian Riesch <[email protected]> Signed-off-by: Rajashekhara, Sudhakar <[email protected]> Signed-off-by: Lad, Prabhakar <[email protected]> Signed-off-by: Hadli, Manjunath <[email protected]>
2012-09-01da850/omap-l138: Add MMC support for DA850/OMAP-L138Lad, Prabhakar
This patch adds support for MMC/SD on DA850/OMAP-L138. Tested-by: Christian Riesch <[email protected]> Signed-off-by: Lad, Prabhakar <[email protected]> Signed-off-by: Rajashekhara, Sudhakar <[email protected]> Signed-off-by: Hadli, Manjunath <[email protected]>
2012-09-01omap: am335x_evm: remove unused definitionsSteve Sakoman
UART_RESET, UART_CLK_RUNNING_MASK, and UART_SMART_IDLE_EN are defined inn evm.c but not used. Also removes unnecessary include of serial.h PHYS_DRAM_1_SIZE is defined in am335x_evm.h but never used. Signed-off-by: Steve Sakoman <[email protected]>
2012-09-01OMAP3: mcx: read hot-water-button after resetStefano Babic
Detect hot-water-button to start a differnt image. Signed-off-by: Stefano Babic <[email protected]> CC: Tom Rini <[email protected]>
2012-09-01OMAP3: mcx: updated default environmentStefano Babic
Patch drops also not used CFI setup in the configuration file. Signed-off-by: Stefano Babic <[email protected]> CC: Tom Rini <[email protected]>
2012-09-01mcx: increased buffer for command lineStefano Babic
Signed-off-by: Stefano Babic <[email protected]> CC: Tom Rini <[email protected]>
2012-09-01hawkboard/omapl-138: Add support for generating ais image for hawkboardSughosh Ganu
Parameters used for configuring certain SoC peripherals are parsed from the cfg file and appended as part of the ais image's header. The u-boot-spl.ais generated is flashed separately to the nand, so do not delete the file after generation of u-boot.ais. Signed-off-by: Sughosh Ganu <[email protected]>
2012-09-01Consolidate bootcount code into drivers/bootcountStefan Roese
This patch moves all bootcount implementations into a common directory: drivers/bootcount. The generic bootcount driver is now usable not only by powerpc platforms, but others as well. Signed-off-by: Stefan Roese <[email protected]> Cc: Heiko Schocher <[email protected]> Cc: Valentin Longchamp <[email protected]> Cc: Christian Riesch <[email protected]> Cc: Manfred Rudigier <[email protected]> Cc: Mike Frysinger <[email protected]> Cc: Rob Herring <[email protected]> Cc: Reinhard Meyer <[email protected]> Tested-by: Valentin Longchamp <[email protected]> Tested-by: Christian Riesch <[email protected]> Acked-by: Rob Herring <[email protected]> Acked-by: Mike Frysinger <[email protected]>
2012-09-01mpc52xx: remove o2dnt boardAnatolij Gustschin
Remove old o2dnt board without OF support. New support for this board is added by the previous patch, O2I configuration. Signed-off-by: Anatolij Gustschin <[email protected]>
2012-09-01mpc52xx: add common o2dnt and o2dnt2 support and configurationsAnatolij Gustschin
Add common code for o2dnt and o2dnt2 based boards and add different board configuration files for O2D, O2I, O2DNT2, O2D300, O2MNT and O3DNT boards. Signed-off-by: Anatolij Gustschin <[email protected]>
2012-08-24MIPS: add support for qemu for little endian MIPS32 CPUsDaniel Schwierzeck
Tested with 'qemu-system-mipsel -machine mips -bios u-boot.bin -nographic' Signed-off-by: Daniel Schwierzeck <[email protected]>
2012-08-24MIPS: factor out endianess flag handling to arch config.mkDaniel Schwierzeck
This is CPU independent and should be configured architecture-wide. Signed-off-by: Daniel Schwierzeck <[email protected]>
2012-08-23powerpc/p1_p2_rdb_pc: print -PC suffix in board nameScott Wood
Currently the -PC variants of the P1/P2 RDB boards do not print it on boot -- e.g. a P2020RDB-PC will claim to be a plain P2020RDB. Besides being incorrect, this can confuse a user into building U-Boot for P2020RDB rather than P2020RDB-PC, resulting in a board that does not boot. P1024RDB and P1025RDB are not included, as these boards apparently do not have -PC as part of their name, even though they are supported by p1_p2_rdb_pc. The P2020RDB variant covered by this is apparently P2020RDB-PCA rather than P2020RDB-PC. Signed-off-by: Scott Wood <[email protected]> Signed-off-by: Andy Fleming <[email protected]>
2012-08-23powerpc/fsl-corenet: remove dead variant symbolsScott Wood
These are not supported as individual build targets, but instead are supported by another target. The dead p4040 defines in particular had bitrotted significantly. Signed-off-by: Scott Wood <[email protected]> Acked-by: Kumar Gala <[email protected]> Signed-off-by: Andy Fleming <[email protected]>
2012-08-23powerpc/85xx: remove support for the Freescale P3060Timur Tabi
The P3060 was cancelled before it went into production, so there's no point in supporting it. Signed-off-by: Timur Tabi <[email protected]> Signed-off-by: Andy Fleming <[email protected]>
2012-08-23powerpc/CoreNet: add tool to support pbl image build.Shaohui Xie
Provides a tool to build boot Image for PBL(Pre boot loader) which is used on Freescale CoreNet SoCs, PBL can be used to load some instructions and/or data for pre-initialization. The default output image is u-boot.pbl, for more details please refer to doc/README.pblimage. Signed-off-by: Shaohui Xie <[email protected]> Signed-off-by: Andy Fleming <[email protected]>
generated by cgit v1.3.1 (git 2.54.0) at 2026-09-03 12:15:07 +0000