| Age | Commit message (Collapse) | Author |
|---|
|
CONFIG_SYS_INIT_SP_ADDR points to RAM, but it's used before
DRAM controller init. Fix it by setting CONFIG_SYS_INIT_SP_ADDR
to SRAM
Signed-off-by: Vasily Khoruzhick <[email protected]>
|
|
The sh7757lcr has 2GByte eMMC chip. This patch supports it.
Signed-off-by: Yoshihiro Shimoda <[email protected]>
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
This patch adds FAT and ext2 command support for marvell gplugD
Signed-off-by: Ajay Bhargav <[email protected]>
|
|
This patch adds support for USB commands and USB storage device for
Marvell gplugD
Signed-off-by: Ajay Bhargav <[email protected]>
|
|
The earlier usb device controller driver was specific to spear platforms. This
patch implements the usb device controller driver as a generic controller which
can be reused by other platforms using this peripheral.
Signed-off-by: Vipin Kumar <[email protected]>
Signed-off-by: Amit Virdi <[email protected]>
Acked-by: Marek Vasut <[email protected]>
|
|
This patch adds support for the esd CPCI-HD/2 board to u-boot for CPCI-CPU/750.
As the primary devices on the CPCI-HD/2 board are connected to device 1 and 3,
the device must be swapped.
Signed-off-by: Reinhard Arlt <[email protected]>
|
|
* 'master' of git://git.denx.de/u-boot-avr32:
atmel_mci.h: remove outdated register macros
doc/git-mailrc: add <me> to avr32 alias
ATMEL: remove old atmel_mci driver
ATMEL: use generic mmc framework
|
|
* 'sandbox' of git://git.denx.de/u-boot-blackfin:
sandbox: mark os_exit as noreturn
sandbox: add getopt support
sandbox: allow processing before main loop
sandbox: add concept of sandbox state
sandbox: disable fortification
sandbox: u-boot.lds: tweak style
sandbox: add get_{tbclk,ticks}
sandbox: enable GPIO driver
sandbox: gpio: add basic driver for simulating GPIOs
sandbox: add flags for open() call
sandbox: config: enable fdt and snprintf() options
sandbox: fdt: add support for CONFIG_OF_CONTROL
sandbox: add lseek helper
sandbox: add ifdef protection to os.h
sandbox: add required header to os.c
sandbox: sort header files in os.c
|
|
gen_atmel_mci works on AVR32 as well, so no need to use the legacy
mmc driver. This also has the nice side effect of being able to use
SDHC cards an those boards.
Signed-off-by: Sven Schnelle <[email protected]>
Signed-off-by: Andreas Bießmann <[email protected]>
|
|
Enable the new GPIO driver for sandbox.
Signed-off-by: Simon Glass <[email protected]>
Signed-off-by: Mike Frysinger <[email protected]>
|
|
Enable fdt code and safe snprintf() options for sandbox.
Signed-off-by: Simon Glass <[email protected]>
Signed-off-by: Mike Frysinger <[email protected]>
|
|
The generalised calculation of the serial bit rate reg also applies
to sh7264, it was just the clock speed that was set incorrectly.
Signed-off-by: Phil Edworthy <[email protected]>
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
Add PREBOOT, SILENT_CONSOLE and DEVICE_NULLDEV for release
build. Fixed bug in CONFIG_SYS_HUSH_PARSER define.
Signed-off-by: Helmut Raiger <[email protected]>
|
|
The video setup for the Epson display is provided. Addtionally
some extra info is displayed next to the Linux logo.
Make get_cpu_rev() publicly available (added to sys_proto.h).
Signed-off-by: Helmut Raiger <[email protected]>
|
|
size of environment must match erasable block size in the flash.
Signed-off-by: Helmut Raiger <[email protected]>
|
|
Define CONFIG_PHY_MICREL, and
minimize the tx clock delay.
There is an issue with 1000 baseTx mode on early revs
of the SabreLite boards. The center tap pin 9 of the mag RJ45
USB combo was connected to the 3.3 filtered supply. Letting
this pin float solved the problem. Symptoms of the problem
were packets with many extra zeroes tacked on the end, and random
bit flips causing a high rate of CRC errors. 10/100 baseTx worked
fine on all revs. To disable 1000 baseTx for these boards, simply
define the environment variable disable_giga. ie.
setenv disable_giga 1
Signed-off-by: Troy Kisky <[email protected]>
Acked-by: Dirk Behme <[email protected]>
|
|
The Integrator/CP config file was very outdated and gives a
non functional U-Boot. So:
- Set the CONFIG_ARCH_CINTEGRATOR arch flag correctly
- Add proper core module configuration options
- Skip cluttered command lista and just include
<config_cmd_default.h>
- Kill off #if 0 network section and insert some example
configuration that simply just boots from the network
using TFTP if available.
- Delete flash control registers that have no business
in this config file. These are already moved down to
board/armltd/integrator/integrator-sc.h
Cc: Will Deacon <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
The PCI support for the Integrator AP has apparently never
been finished and I strongly suspect that it has never worked,
so let's fix it. This is a list of the more or less
un-splittable changes done in this driver rewrite:
- Replace the register definitions stashed into the config
file (!) with a copy if the register file from the Linux
kernels arch/arm/include/asm/hardware/pci_v3.h
- Delete the unreadable gigantic macros that perform the
config accesses and replace them with copyedited code from
Linux arch/arm/mach-integrator/pci_v3.c
- Rewrite the rest of the setup code to use the
v3_[read|write][lwb]() accessors.
- Enable PCI by default in the AP board configuration.
- Fix checkpatch warnings and make code more conformant.
Tested-by: Will Deacon <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
Signed-off-by: Detlev Zundel <[email protected]>
CC: Stefano Babic <[email protected]>
|
|
davinci_dm6467Tevm
In commit 2d575e46859dd9127a9cec731ace77523e6ea2ab a separate header
file was introduced for the DM6467T EVM, include/configs/davinci_dm6467Tevm.h.
The substantial difference between the davinci_dm6467evm and the
davinci_dm6467Tevm configuration is a single bit in the hardware revision
that is passed to the Linux kernel and davinci_dm6467evm has
REFCLK_FREQ = 27000000 where as davinci_dm6467Tevm.h has a
REFCLK_FREQ = 33000000.
This patch removes include/configs/davinci_dm6467Tevm.h. Instead the
include/configs/davinci_dm6467evm.h configuration is used for DM6467T EVMs and
renamed CFG_REFCLK_FREQ to CONFIG_REFCLK_FREQ and CONFIG_REFCLK_FREQ is defined
in boards.cfg.
Signed-off-by: Prabhakar Lad <[email protected]>
Cc: Tom Rini <[email protected]>
|
|
Signed-off-by: Thomas Weber <[email protected]>
|
|
Because the tricorder uses the CONFIG_OMAP_HSMMC the
initialization command is mmc rescan and not mmc init.
Signed-off-by: Thomas Weber <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
The default settings store the persistent environment on SD card
and not serial flash (SPI NOR).
To use SPI NOR to save the environment instead of SD card, edit
include/configs/mx6qsabrelite.h and
- undefine CONFIG_ENV_IS_IN_MMC
- define CONFIG_ENV_IS_IN_SPI_FLASH
The SPI driver can take as chip select the controller's chip selects
as well as an external GPIO. The LSB byte has the value of the internal
chip select, the highest (thought as 16-bit value) contains the GPIO
number.
The GPIO used on Sabre Lite is GP3:19 == 83.
Signed-off-by: Eric Nelson <[email protected]>
Acked-by: Jason Liu <[email protected]>
Tested-by: Jason Liu <[email protected]>
|
|
Signed-off-by: Eric Nelson <[email protected]>
Acked-by: Dirk Behme <[email protected]>
Acked-by: Stefano Babic <[email protected]>
Acked-by: Jason Liu <[email protected]>
Tested-by: Jason Liu <[email protected]>
|
|
Signed-off-by: Eric Nelson <[email protected]>
Acked-by: Dirk Behme <[email protected]>
Acked-by: Stefano Babic <[email protected]>
Acked-by: Jason Liu <[email protected]>
Tested-by: Jason Liu <[email protected]>
|
|
This patch adds SPI support for the MX28EVK. Support for
an optionally installed SPI flash is also added. An example
configuration for redundant envrionment from SPI flash is also
added but disabled by default.
This patch has been tested on a MX28EVK Rev. D with an installed
SST25VF032B 32Mbit SPI flash.
Signed-off-by: Matthias Fuchs <[email protected]>
Acked-by: Fabio Estevam <[email protected]>
|
|
This patch enables USB host support on the MX28EVK board.
Signed-off-by: Matthias Fuchs <[email protected]>
Tested-by: Fabio Estevam <[email protected]>
|
|
This patch adds support for the MX28 internal RTC
and enables u-boot's date command.
Signed-off-by: Matthias Fuchs <[email protected]>
Tested-by: Fabio Estevam <[email protected]>
|
|
* Adjust the GBL_DATA_OFFSET to account for the fact that we'll be
using the space between that offset and the start of the malloc
region to allocate both a gd structure and a board info structure.
* This fixes a memory corruption bug due to overlap of the malloc
region and the bd_info structure.
Signed-off-by: Alex Hornung <[email protected]>
Signed-off-by: Thomas Chou <[email protected]>
|
|
Signed-off-by: Stephan Linz <[email protected]>
|
|
* 'master' of git://git.denx.de/u-boot-blackfin:
Blackfin: pata_bfin: fix printf warning
Blackfin: bfin_nand: mark local func static
linkage.h: move from blackfin to common includes
Blackfin: br4: new board port
Blackfin: add in/out le32 variants
post: add blackfin to the post_time_ms list
Blackfin: bf537-stamp: drop board reset workaround
Blackfin: pr1: new board port
|
|
This adds support for the BR4 Appliance. It is a quad channel ISDN BRI
board based on Blackfin BF537 CPU.
Signed-off-by: Dimitar Penev <[email protected]>
Signed-off-by: Mike Frysinger <[email protected]>
|
|
This add support for the PR1 Appliance - Asterisk based ISDN PRI PBX.
This board is Blackfin BF537 based. The schematics are not fully opened.
Signed-off-by: Dimitar Penev <[email protected]>
Signed-off-by: Mike Frysinger <[email protected]>
|
|
This patch adds support for the Calimain board from
OMICRON electronics GmbH. The board features a Texas Instruments AM1808
SoC, 128 MB DDR2 memory, and 64 MB NOR flash memory connected to CS2 and
CS3.
Signed-off-by: Christian Riesch <[email protected]>
|
|
This patch moves hawkboard to the new spl infrastructure from the
older nand_spl one.
Removed the hawkboard_nand_config build option -- The spl code now
gets compiled with hawkboard_config, after building the main u-boot
image, using the CONFIG_SPL_TEXT_BASE. Modified the README.hawkboard
to reflect the same.
Signed-off-by: Sughosh Ganu <[email protected]>
Signed-off-by: Heiko Schocher <[email protected]>
Cc: Heiko Schocher <[email protected]>
Cc: Christian Riesch <[email protected]>
Cc: Sudhakar Rajashekhara <[email protected]>
Cc: Tom Rini <[email protected]>
Acked-by: Christian Riesch <[email protected]>
|
|
The V bit of the c1 register of CP15 should not be cleared on DA850
SoCs since they have no valid memory at 0x00000000. This patch
introduces a configuration option CONFIG_SYS_EXCEPTION_VECTORS_HIGH
that allows setting the correct value for the V bit.
Signed-off-by: Christian Riesch <[email protected]>
Reported-by: Sughosh Ganu <[email protected]>
Cc: Albert Aribaud <[email protected]>
Cc: Tom Rini <[email protected]>
Cc: Sughosh Ganu <[email protected]>
Cc: Heiko Schocher <[email protected]>
|
|
This patch reverts commit ca4b55800ed74207c35271bf7335a092d4955416
"arm, arm926ejs: always do cpu critical inits" since it impacts all
arm926ejs based configurations and caused problems, e.g., with
the hawkboard.
Instead the patch removes the CONFIG_SKIP_LOWLEVEL_INIT defines
from the board configurations that need low level initialization.
Signed-off-by: Christian Riesch <[email protected]>
Cc: Albert Aribaud <[email protected]>
Cc: Tom Rini <[email protected]>
Cc: Heiko Schocher <[email protected]>
Acked-by: Heiko Schocher <[email protected]>
Tested-by: Heiko Schocher <[email protected]>
|
|
add support for printing various clock frequency info found
in SOC such as ARM core frequency, DSP core frequency and DDR
frequency as part of bdinfo command.
Signed-off-by: Manjunath Hadli <[email protected]>
Cc: Tom Rini <[email protected]>
|
|
remove the macro CONFIG_DISPLAY_CPUINFO as it is no longer
required. This is because clock info will be printed as part
'bdinfo' command and also remove support print_cpuinfo() as it will
no longer be called.
Signed-off-by: Manjunath Hadli <[email protected]>
Cc: Tom Rini <[email protected]>
|
|
This patch adds support for the HTKW mcx AM3517-based board.
Serial, Ethernet, NAND, MMC, RTC, EHCI USB host and both
NAND and MMC SPLs are supported.
Signed-off-by: Ilya Yanok <[email protected]>
Signed-off-by: Stefano Babic <[email protected]>
CC: Tom Rini <[email protected]>
Cc: Detlev Zundel <[email protected]>
Acked-by: Igor Grinberg <[email protected]>
|
|
The mt_ventoux board is a custom board using
the Technexion TAM3517 module.
The patch fixes also the mtdparts variable in the
TAM3517 common configuration file.
Signed-off-by: Stefano Babic <[email protected]>
CC: Ilya Yanok <[email protected]>
CC: Igor Grinberg <[email protected]>
CC: Tom Rini <[email protected]>
Cc: Detlev Zundel <[email protected]>
Acked-by: Igor Grinberg <[email protected]>
|
|
Changed the EHCI interface using the ulpi framework.
Signed-off-by: Stefano Babic <[email protected]>
CC: Tom Rini <[email protected]>
Acked-by: Igor Grinberg <[email protected]>
|
|
For panda initialise the mux pins for ehci usage and
enable ehci in omap4_panda config file.
Signed-off-by: Govindraj.R <[email protected]>
Tested-by: Stefano Babic <[email protected]>
|
|
Taken from Beagle code. Tested on mcx board (AM3517-based).
Signed-off-by: Ilya Yanok <[email protected]>
Tested-by: Stefano Babic <[email protected]>
|
|
Based on discussion from this thread [1].
Adding omap-view port that helps us in using the generic ulpi
framework for any ulpi phy ops using the INSNREG05_ULPI viewport
reg available on omap platform.
Currently ehci ports are available on omap3/4 platforms so enable the same
for beagle and panda, patch is tested on the same boards.
Thanks to Igor Grinberg <[email protected]> for reviewing the
omap-ehci patches and suggesting this approach.
[1]: http://www.mail-archive.com/[email protected]/msg76076.html
Tested-by: Stefano Babic <[email protected]>
Acked-by: Igor Grinberg <[email protected]>
Signed-off-by: Govindraj.R <[email protected]>
|
|
This patch enable support for SMC911X based ethernet device.
Signed-off-by: Chander Kashyap <[email protected]>
Acked-by: Mike Frysinger <[email protected]>
Acked-by: Simon Glass <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
This patch adds support for MMC SPL booting.
Signed-off-by: Chander Kashyap <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
SMDK5250 board is based on Samsungs EXYNOS5250 SoC.
Signed-off-by: Chander Kashyap <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
CONFIG_SYS_CLK_FREQ_C210 macro giving notion of S5PC2XX (Exynos4)
architecture. Replace CONFIG_SYS_CLK_FREQ_C210 with CONFIG_SYS_CLK_FREQ
to make it generic for exynos architecture.
Signed-off-by: Chander Kashyap <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
