| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
Signed-off-by: Wolfgang Denk <[email protected]>
Cc: Stefan Roese <[email protected]>
Cc: Reinhard Arlt <[email protected]>
|
|
Remove dead code that was obviously a left-over from copy & paste.
Signed-off-by: Wolfgang Denk <[email protected]>
Cc: Stefan Roese <[email protected]>
Cc: Reinhard Arlt <[email protected]>
|
|
Needed for Rev. 2 silicon at 400 MHz
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
When enabling NAND support for a board, one must also define
CONFIG_SYS_64BIT_VSPRINTF because this is needed in nand_util.c
for correct output.
Signed-off-by: Wolfgang Denk <[email protected]>
Cc: Stefan Roese <[email protected]>
Cc: Reinhard Arlt <[email protected]>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
Signed-off-by: Peter Pearse <[email protected]>
Cc: Catalin Marinas <[email protected]>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
Signed-off-by: Peter Pearse <[email protected]>
Cc: Catalin Marinas <[email protected]>
|
|
AT91sam9g10 is an ARM 926ej-s SOC. It is an evolution of the at91sam9261 with a
faster clock speed: 266/133MHz.
Signed-off-by: Sedji Gaouaou <[email protected]>
|
|
AT91sam9g45 series is an ARM 926ej-s SOC family clocked at 400/133MHz.
It embeds USB high speed host and device, LCD, DDR2 RAM, and a full set of
peripherals.
The first board that embeds at91sam9g45 chip is the AT91SAM9G45-EKES.
On the board you can find 2 USART, USB high speed,
a 480*272 LG lcd, ethernet, gpio/joystick/buttons.
Signed-off-by: Sedji Gaouaou <[email protected]>
|
|
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
ESPT-Giga is SH7763-based reference board.
Board support is relatively sparse, presently supporting serial,
gigabit ethernet, USB host, and MTD.
More information (in Japanese) available at:
http://www.cente.jp/product/cente_hard/ESPT-Giga.html
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
The KSEG1ADDR macro used to be necessary for the RTL8139 Ethernet
driver, but the code that used that macro was removed over a year
ago, so board configuration files no longer need to define it.
The _IO_BASE macro is also automatically defined to 0 if it isn't
already set, so there's no need to define that macro either in the
board configuration files.
Signed-off-by: Timur Tabi <[email protected]>
Acked-by: Nobuhiro Iwamatsu <[email protected]>
Acked-by: Andy Fleming <[email protected]>
Acked-by: Andre Schwarz <[email protected]>
Acked-by: Kim Phillips <[email protected]>
|
|
Add support for the Phytec phyCORE-MPC5200B-tiny.
Code originally from Pengutronix.de.
Created CONFIG_SYS_ATA_CS_ON_TIMER01 define for when IDE CS is on
Timer 0/1
Signed-off-by: Jon Smirl <[email protected]>
Acked-by: Grant Likely <[email protected]>
|
|
The cm-bf561 module can easily hook up to the EXT-BF5xx-USB-ETH2 extender
board, so add a simple example of how to do that in the board config.
Signed-off-by: Harald Krapfenbauer <[email protected]>
Signed-off-by: Mike Frysinger <[email protected]>
|
|
The latest blackstamp boards can only run the SPI flash at 15MHz before
they start to crap out, so lower the max speeds accordingly. The new SPI
flash also has different sector requirements, so update the environment
sizes as well.
Signed-off-by: Mike Frysinger <[email protected]>
|
|
|
|
This patch fixes 2 problems with FDT EBC mappings on Canyonlands.
First, NAND EBC mapping was missing, making Linux NAND driver
unusable on this board. Second, NOR remapping code assumed that
NOR is always on CS0, however when booting from NAND NOR is on CS3.
Signed-off-by: Felix Radensky <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
Cc: Nobuhiro Iwamatsu <[email protected]>
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
Cc: Nobuhiro Iwamatsu <[email protected]>
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
Currently, when booting from NAND using nand_spl, in the beginning the default
environment is used until later in boot process the dynamic environment is read
out. This way environment variables that must be interpreted early, like the
baudrate or "silent", cannot be modified dynamically and remain at their
default values. Fix this problem by reading out main and redundand (if used)
copies of the environment in the nand_spl code.
Signed-off-by: Guennadi Liakhovetski <[email protected]>
Signed-off-by: Scott Wood <[email protected]>
|
|
The BF537-STAMP Blackfin board had a driver for working with NAND devices
that are simply memory mapped. Since there is nothing Blackfin specific
about this, generalize the driver a bit so that everyone can leverage it.
Signed-off-by: Mike Frysinger <[email protected]>
Signed-off-by: Scott Wood <[email protected]>
|
|
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
Conflicts:
drivers/spi/Makefile
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
|
|
Signed-off-by: Magnus Lilja <[email protected]>
|
|
This sets CONFIG_SYS_HZ to 1000 as required, and completely rewrites
timer code, which is now both correct and much smaller. Unused
functions like udelay_masked() have been removed as no driver uses
them, even the ones that are not currently active for this board.
mtu.h is copied literally from the kernel sources.
Signed-off-by: Alessandro Rubini <[email protected]>
Acked-by: Andrea Gallo <[email protected]>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
|
|
The evaluation kit has both Nand and OneNand, both drivers are there
and the two configurations only select a different default for the
jffs partition. This adds the OneNand driver and cleans up storage.
Signed-off-by: Alessandro Rubini <[email protected]>
Acked-by: Andrea Gallo <[email protected]>
|
|
There is only one public release of the Nomadik chip, so the ifdef
in reset code as well as a define in the config file are not needed
Signed-off-by: Alessandro Rubini <[email protected]>
Acked-by: Andrea Gallo <[email protected]>
|
|
This is an error in my side in the initial submission: nobody
calls it ""nmdk8815", it's "nomadik hardware kit", nhk8815, instead.
Signed-off-by: Alessandro Rubini <[email protected]>
Acked-by: Andrea Gallo <[email protected]>
|
|
The Polaris board is based on the TrizepsIV module of
Keith & Koep (http://www.keith-koep.com).
Signed-off-by: Stefano Babic <[email protected]>
|
|
This patch adds support for esd gmbh MEESC board.
The MEESC is based on an Atmel AT91SAM9263 SoC.
Signed-off-by: Daniel Gorsulowski <[email protected]>
|
|
Add support for Freescale's i.MX31 PDK board (a.k.a. 3 stack board).
This patch assumes that some other program performs the actual
NAND boot.
Signed-off-by: Magnus Lilja <[email protected]>
Acked-by: Fabio Estevam <[email protected]>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
Cc: Peter Pearse <[email protected]>
|
|
Initial support for Extreme Engineering Solutions XPedite5170 -
a MPC8640-based 3U VPX single board computer with a PMC/XMC
site.
Signed-off-by: Peter Tyser <[email protected]>
Signed-off-by: Kumar Gala <[email protected]>
|
|
DMA support is now enabled via the CONFIG_FSL_DMA define instead of the
previous CONFIG_DDR_ECC
Signed-off-by: Peter Tyser <[email protected]>
Signed-off-by: Kumar Gala <[email protected]>
|
|
Signed-off-by: Roy Zang <[email protected]>
Signed-off-by: Kumar Gala <[email protected]>
|
|
We want the outbound PCI memory map to end at the 4G boundary so we
can maximize the amount of space available for inbound mappings if
we have large amounts of memory.
This matches the device tree setup in the kernel for the 36-bit physical
configs for the platforms that have one (MPC8641 HPCN & MPC8572 DS).
Signed-off-by: Kumar Gala <[email protected]>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
Acked-by: Peter Pearse <[email protected]>
|
|
UART hardware on i.MX27 is the same as on the i.MX31 so we just
need to provide the driver with correct address of the registers.
Signed-off-by: Ilya Yanok <[email protected]>
|
|
this will allow you to store use it for the env and to boot directly U-Boot from
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
|
|
The PM9261 board is based on the AT91SAM9261-EK board.
Here is the page on Ronetix website:
http://www.ronetix.at/starter_kit_9261.html
Signed-off-by: Ilko Iliev <[email protected]>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
|
|
optimize a few the RAM init
Signed-off-by: Ilko Iliev <[email protected]>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
|
