| Age | Commit message (Collapse) | Author |
|---|
|
Add initial support for Compulab iot-gate-imx8 board (imx8mm-cl-iot-gate).
The initial support includes:
- MMC
- eMMC
- I2C
- FEC
- Serial console
Signed-off-by: Kirill Kapranov <[email protected]>
Signed-off-by: Uri Mashiach <[email protected]>
Signed-off-by: Valentin Raevsky <[email protected]>
Signed-off-by: Ying-Chun Liu (PaulLiu) <[email protected]>
Cc: Peter Robinson <[email protected]>
|
|
Engicam EDIMM2.2 Starter Kit is an EDIMM 2.2 Form Factor Capacitive
Evaluation Board.
Genaral features:
- LCD 7" C.Touch
- microSD slot
- Ethernet 1Gb
- Wifi/BT
- 2x LVDS Full HD interfaces
- 3x USB 2.0
- 1x USB 3.0
- HDMI Out
- Mini PCIe
- MIPI CSI
- 2x CAN
- Audio Out
i.Core MX8M Mini is an EDIMM SoM based on NXP i.MX8M Mini from Engicam.
i.Core MX8M Mini needs to mount on top of this Evaluation board for
creating complete i.Core MX8M Mini EDIMM2.2 Starter Kit.
Linux dts commit details:
commit <051c08eea682> ("arm64: dts: imx8mm: Add Engicam i.Core MX8M Mini
EDIMM2.2 Starter Kit")
Add support for it.
Signed-off-by: Jagan Teki <[email protected]>
|
|
Prevent shell access on boot failure by entering an infinite
loop.
Signed-off-by: Ian Ray <[email protected]>
Signed-off-by: Sebastian Reichel <[email protected]>
|
|
Minor cosmetic changes to unify `CONFIG_EXTRA_ENV_SETTINGS'
indentation between Bx50v3 and PPD to make comparison and
review easier and simplify the default boot command.
Signed-off-by: Ian Ray Ian Ray <[email protected]>
Signed-off-by: Sebastian Reichel <[email protected]>
|
|
Remove unsupported USB boot.
Signed-off-by: Ian Ray <[email protected]>
Signed-off-by: Sebastian Reichel <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2021.07-rc2
xilinx:
- Enable saving variables based on bootmode
- Cleanup usb dfu setup and wire it up with usb bootmode
- Fix bootscript address logic
- Remove GD references (spi, Versal)
- Enable capsule update
clk:
- Small Kconfig fix
net:
- Fix gmii2rgmii bridge binding
usb:
- Propagate error (dfu gadget)
|
|
- RCar3 improvements
|
|
Enable EFI capsule update features to be enabled by default also with all
dfu valid options for ZynqMP.
This feature was tested on Xilinx ZynqMP zcu104 board with defining
dfu_alt_info="mmc 0:1=boot.bin fat 0 1;u-boot.itb fat 0 1"
and
dfu_alt_info="sf 0:0=boot.bin raw 0 0x50000;u-boot.itb raw 0x80000
0x500000".
There is a need to increase malloc size for getting dfu mmc to work.
Signed-off-by: Michal Simek <[email protected]>
CC: Sughosh Ganu <[email protected]>
CC: Ilias Apalodimas <[email protected]>
CC: Heinrich Schuchardt <[email protected]>
|
|
Enable CONFIG_SYS_FLASH_PROTECTION on Salvator-X(S), ULCB, Ebisu,
which means the Spansion HF PPB protection bits can be operated
using the 'protect' U-Boot command.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Nobuhiro Iwamatsu <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-mips
- MIPS: octeon: fix minor bugs of initial merge
- MIPS: octeon: add support for QLM and PCI-E controller
- MIPS: octeon: add support for AHCI and SATA
- MIPS: octeon: add E1000 ethernet support
- MIPS: octeon: add Octeon III NIC23 board
- ata/scsi: add support for Big Endian platforms
|
|
This patch adds the basic support for the PCIe target board equipped
with the Octeon III CN2350 SoC.
Signed-off-by: Stefan Roese <[email protected]>
|
|
Add support for usb dfu & thor to distro boot on zynq platform.
Add 60s timeout of dfu-utils to start transaction. Remove
DFU_ALT_INFO_RAM as we use bootcmd_usb_dfu instead of dfu_ram.
Remove DFU_ALT_INFO_MMC as part of distro boot cleanup.
Signed-off-by: T Karthik Reddy <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
Change "dfu_usb" to "usb_dfu" for better representation and change
required macros. Add 60s timeout of dfu-utils to start transaction.
Add support for usb thor to distro boot. Remove DFU_ALT_INFO_RAM
as we use bootcmd_usb_dfu instead of dfu_ram.
Signed-off-by: T Karthik Reddy <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
The dfu ram info is wired in connection to Linux kernel and certain setup.
We should change this to be more generic as others command. That's why
using boot via script is the way to go.
Signed-off-by: Michal Simek <[email protected]>
|
|
In usb boot mode distro boot should select usb device as primary boot
device instead of usb host. So make usb dfu as primary boot device. But do
not list it in boot_targets as fallback option because it is not classic
mode for booting. Using 60s timeout by default should be enough time for
dfu-utils to start transaction. In case none needs this please change
timeout value in the command or disable CONFIG_DFU_TIMEOUT.
Signed-off-by: T Karthik Reddy <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
Migrate CONFIG_LMB in Kconfig.
Signed-off-by: Patrick Delaunay <[email protected]>
|
|
Convert the UDOO Neo to ethernet DM support.
Signed-off-by: Peter Robinson <[email protected]>
Cc: Francesco Montefoschi <[email protected]>
Cc: Breno Lima <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Stefano Babic <[email protected]>
|
|
So far we were defining a somewhat confusing PHYS_SDRAM_1_SIZE variable,
which originally was only used for setting the memtest boundaries. This
definition in highbank.h has been removed about a year ago (moved to
Kconfig), so we also don't need the hard-coded size definition any longer.
Get rid of the misleading memory size definition, which was actually wrong
anyway (it's 4088 MB for those machines with just 4GB of DRAM).
Signed-off-by: Andre Przywara <[email protected]>
|
|
To squash that nasty warning message and make better use of the newly
gained OF_CONTROL feature, let's convert the calxedagmac driver to the
"new" driver model.
The conversion is pretty straight forward, mostly just adjusting the
use of the involved data structures.
The only actual change is the required split of the receive routine into
a receive and free_pkt part.
Also this allows us to get rid of the hardcoded platform information and
explicit init calls.
This also uses the opportunity to wrap the code decoding the MMIO
register base address, to make it safe for using PHYS_64BIT later.
Signed-off-by: Andre Przywara <[email protected]>
Reviewed-by: Ramon Fried <[email protected]>
|
|
All Calxeda machines are actually a poster book example of device tree
usage: the DT is loaded from flash by the management processor into
DRAM, the memory node is populated with the detected DRAM size and this
DT is then handed over to the kernel.
So it's a shame that U-Boot didn't participate in this chain, but
fortunately this is easy to fix:
Define CONFIG_OF_CONTROL and CONFIG_OF_BOARD, and provide a trivial
function to tell U-Boot about the (fixed) location of the DTB in DRAM.
Then enable DM_SERIAL, to let the PL011 driver pick up the UART platform
data from the DT. Also define AHCI, to bring this driver into the driver
model world as well.
Signed-off-by: Andre Przywara <[email protected]>
|
|
So far on Highbank/Midway machines U-Boot only ever uses 512MB of DRAM,
even though the machines have typically 4GB and 8GB, respectively.
That means that so far we didn't need an extra limit for placing the DTB
and initrd, as the 512MB are lower than the kernel's limit ("lowmem",
typically 768MB).
With U-Boot now needing to learn about the actual memory size (to
correctly populate the EFI memory map), it might relocate fdt and initrd
to the end of DRAM, which is out of reach of the kernel.
So add limiting values to the fdt_high and initrd_high environment
variables, to prevent U-Boot from using too high addresses.
Signed-off-by: Andre Przywara <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Support Generic Distro Default config
Signed-off-by: Tim Harvey <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Move CONFIG_SUPPORT_RAW_INITRD out of the octeontx_common header
and into the defconfig files.
Signed-off-by: Tim Harvey <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Let's add a boot target for NVMe so we can do a full boot over NVMe.
Signed-off-by: Neil Armstrong <[email protected]>
|
|
This is a patchset which makes away with the .bind() controller indexing
workaround which was broken since before v2021.04, and then adds PHY
support and MX8M support on top of that. Better add it into the release
early to get as much testing as possible done, because this really does
a lot of changes to the ehci-mx6 driver.
|
|
Enable USB host support on MX8MM Verdin.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Marcel Ziswiler <[email protected]>
Cc: Max Krummenacher <[email protected]>
Cc: Oleksandr Suvorov <[email protected]>
|
|
The "booti" command to load arm64 Linux kernels supports automatic
decompression of zipped kernel images, but relies on some environment
variables to point to usable buffer RAM.
Add those variables and let them point to some default values, that
should cover most use-cases.
Signed-off-by: Andre Przywara <[email protected]>
|
|
Commit 69076dff2284 ("cmd: pxe: add support for FDT overlays") added
support for loading DT overlay files to PXE boot. However, it needs
additional environment variable which points to memory location which
can be used to temporary store overlay data.
Add it and in the process unify alignment using spaces and fix comment.
Reviewed-by: Andre Przywara <[email protected]>
Signed-off-by: Jernej Skrabec <[email protected]>
Signed-off-by: Andre Przywara <[email protected]>
|
|
scan_dev_for_efi is supposed to be called from scan_dev_for_boot.
However, this call is missing for ls1012a boards. As a result EFI
boot doesn’t work. Fix this issue by removing custom definition of
scan_dev_for_boot and use the default definition instead.
Signed-off-by: Mian Yousaf Kaukab <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
With all preparations in place, switch over to DM_SERIAL.
Signed-off-by: Michael Walle <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
The DSA sandbox driver is used for unit testing the DSA class code.
It implements a simple 2 port switch plus 1 CPU port, and uses a
very simple tag to identify the ports.
The DSA sandbox device is connected via CPU port to a regular Ethernet
sandbox device, called 'dsa-test-eth, managed by the existing eth
sandbox driver. The 'dsa-test-eth' is not intended for testing the
eth class code however, but it is used to emulate traffic through the
'lan0' and 'lan1' front pannel switch ports. To achieve this the dsa
sandbox driver registers a tx handler for the 'dsa-test-eth' device.
The switch ports, labeled as 'lan0' and 'lan1', are also registered
as eth devices by the dsa class code this time. So pinging through
these switch ports is as easy as:
=> setenv ethact lan0
=> ping 1.2.3.5
Unit tests for the dsa class code were also added. The 'dsa_probe'
test exercises most API functions from dsa.h. The 'dsa' unit test
simply exercises ARP/ICMP traffic through the two switch ports,
including tag injection and extraction, with the help of the dsa
sandbox driver.
I took care to minimize the impact on the existing eth unit tests,
though some adjustments needed to be made with the addition of
extra eth interfaces used by the dsa unit tests. The additional eth
interfaces also require MAC addresses, these have been added to the
sandbox default environment.
Signed-off-by: Alex Marginean <[email protected]>
Signed-off-by: Claudiu Manoil <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Vladimir Oltean <[email protected]>
Message-Id: <[email protected]>
Signed-off-by: Bin Meng <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
The SELI8 design is a new tdm service unit card for Hitachi-Powergrids
XMC and FOX product lines.
It is based on NXP LS1021 SoC and it provides following interfaces:
- IFC interface for NOR, NAND and external FPGA's
- 1 x RGMII ETH for debug purposes
- 2 x SGMII ETH for management communication via back-plane
- 1 x uQE HDLC for management communication via back-plane
- 1 x I2C for peripheral devices
- 1 x SPI for peripheral devices
- 1 x UART for debug logging
It is foreseen that the design will be later re-used for another XMC and
FOX service cards with similar SoC requirements.
Signed-off-by: Rainer Boschung <[email protected]>
Signed-off-by: Matteo Ghidoni <[email protected]>
Signed-off-by: Aleksandar Gerasimovski <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
It's an old bringup board with out upstream Linux or L4T support
Signed-off-by: Peter Robinson <[email protected]>
Cc: Stephen Warren <[email protected]>
Cc: Tom Warren <[email protected]>
Acked-by: Stephen Warren <[email protected]>
|
|
Add power_max77696_init() function.
Since warp doesn't support DM, the keeping its code in board file is
better than maintainig the file of driver.
Signed-off-by: Jaehoon Chung <[email protected]>
|
|
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Priyanka Jain <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
These boards have not been converted to CONFIG_DM_MMC by the deadline.
Remove them. As the P5020 is the last ARCH_P5020 platform, remove that
support as well.
Cc: Andy Fleming <[email protected]>
Cc: Priyanka Jain <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
These boards have not been converted to CONFIG_DM_MMC by the deadline.
Remove them.
Cc: Mario Six <[email protected]>
Cc: Dirk Eibach <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
These boards have not been converted to CONFIG_DM_MMC, along with other
DM conversions, by the deadline. Remove them.
Cc: Dirk Eibach <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
These boards have not been converted to CONFIG_DM_MMC, along with other
DM conversions, by the deadline. Remove them.
Cc: Dirk Eibach <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Ilya Yanok <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it. It is also the only ARCH_T2081 board so remove that support
as well.
Cc: Shengzhou Liu <[email protected]>
Cc: Ruchika Gupta <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Jason Liu <[email protected]>
Cc: Ye Li <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Otavio Salvador <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Stefan Roese <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Lucile Quirion <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Jason Liu <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Stefano Babic <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
These boards have not been converted to CONFIG_DM_MMC by the deadline.
Remove them.
Cc: Stefano Babic <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Paul Kocialkowski <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Nagendra T S <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
