| Age | Commit message (Collapse) | Author |
|---|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2021.01-v2
common:
- Add support for 64bit loadables from SPL
xilinx:
- Update documentation and record ownership
- Enable eeprom board detection based legacy and fru formats
- Add support for FRU format
microblaze:
- Optimize low level ASM code
- Enable SPI/I2C
- Enable distro boot
zynq:
- Add support for Zturn V5
zynqmp:
- Improve silicon detection code
- Enable several kconfig options
- Align DT with the latest state
- Enabling security commands
- Enable and support FPGA loading from SPL
- Optimize xilinx_pm_request() calling
versal:
- Some DTs/Kconfig/defconfig alignments
- Add binding header for clock and power
zynq-sdhci:
- Add support for tap delay programming
zynq-spi/zynq-qspi:
- Use clock framework for getting clocks
xilinx-spi:
- Fix some code issues (unused variables)
serial:
- Check return value from clock functions in pl01x
|
|
- Bug fixes and updates on vid, ls1088a lx2160a and other layerscape
platforms.
- Add optee_rpmb support for LX2 & Kontron sl28 support
|
|
Trivial fix.
Fixes: e519f03a1846 ("cmd: mem: Remove CONFIG_SYS_MEMTEST_SCRATCH mapping")
Signed-off-by: Michal Simek <[email protected]>
|
|
Add distro boot support for microblaze and enable jtag, qspi,
dhcp, pxe boot targets for distro boot.
Enable DISTRO_DEFAULTS config in microblaze defconfig and also
enable support for spi xilinx driver & spi vendors to access
spi flash by distro boot.
Signed-off-by: T Karthik Reddy <[email protected]>
Signed-off-by: Ashok Reddy Soma <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
Set proper indentation for env variables in microblaze header file.
Signed-off-by: T Karthik Reddy <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
Implement early init by calling generic board_init_f_alloc_reserve and
board_init_f_init_reserve functions:
* drop SYS_MALLOC_F_LEN related code, as allocation and gd->malloc_base
assignment are taken care of by the generic functions
* drop _gd logic
Cc: Michal Simek <[email protected]>
Signed-off-by: Ovidiu Panait <[email protected]>
|
|
Remove CONFIG_VIDEO dependency to fix board removal warnings.
Signed-off-by: Anatolij Gustschin <[email protected]>
Cc: Jens Scharsig <[email protected]>
|
|
|
|
Add basic support for the Kontron SMARC-sAL28 board. This includes just
the bare minimum to be able to bring up the board and boot linux.
For now, the Single and Dual PHY variant is supported. Other variants
will fall back to the basic variant.
In particular, there is no watchdog support for now. This means that you
have to disable the default watchdog, otherwise you'll end up in the
recovery bootloader. See the board README for details.
Signed-off-by: Michael Walle <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Tested-by: Heiko Thiery <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
add Kconfig option for pcf8563 driver and
run tools/moveconfig.py
Signed-off-by: Heiko Schocher <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Instead having a hard coded value for "cramfsaddr" after compile time,
we change it to take the variable "cramfsaddr" for the ubicopy variable.
This makes sure that ubicopy uses the right address, even when
the value for "cramfsaddr" has changed.
CC: Valentin Longchamp <[email protected]>
CC: Heiko Schocher <[email protected]>
CC: Tom Rini <[email protected]>
Signed-off-by: Holger Brunck <[email protected]>
Reviewed-by: Heiko Schocher <[email protected]>
|
|
Due to increasing kernel image sizes we get problems when decompressing
the kernel image. To fix this we need to change the addresses where we
load and where we extract the kernel. Also we need to adapt the address
where to load the CRAMFS image and where to load the DTB file.
While at it also harmonize all boards for PPC and ARM to have the
same values. Also we add a new variable "env_version", so that the
userspace is able to detect if this is a u-boot binary with updated
values or not.
CC: Valentin Longchamp <[email protected]>
CC: Heiko Schocher <[email protected]>
CC: Tom Rini <[email protected]>
Signed-off-by: Holger Brunck <[email protected]>
Reviewed-by: Heiko Schocher <[email protected]>
[trini: Remove old values from kmp204x.h]
Signed-off-by: Tom Rini <[email protected]>
|
|
As the ownership is now Hitachi Power Grids, change the license string
and adapt the compatible string in DTS files. For kmeter1.dts we
change it to "keymile,KMETER1" for now, as this is then compliant with
what is submitted to the linux kernel. All other boards don't have
a upstreamed version in linux mainline.
Signed-off-by: Holger Brunck <[email protected]>
CC: Valentin Longchamp <[email protected]>
CC: Heiko Schocher <[email protected]>
CC: Marek Vasut <[email protected]>
CC: Tom Rini <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel features for 2021.01 cycle:
This feature set brings the rework of the clock tree for sam9x60 SoC.
This makes the clock tree fully compatible with Common Clock Framework
and allows full clock configuration in U-Boot. This means that the
sam9x60 boards can boot now using U-Boot.
This also includes the definitions for sam9x60 SiPs and a divisor fix
for the clock on sama7g5 SoC.
|
|
Heap base address is computed based on SYS_INIT_SP_ADDR by
subtracting the SYS_MALLOC_F_LEN value in
board_init_f_init_reserve().
Signed-off-by: Claudiu Beznea <[email protected]>
|
|
Done with:
./tools/moveconfig.py BMP_16BPP BMP_24BPP BMP_32BPP
Signed-off-by: Patrick Delaunay <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Done with:
./tools/moveconfig.py VIDEO_BMP_RLE8
Signed-off-by: Patrick Delaunay <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Done with:
./tools/moveconfig.py VIDEO_BMP_GZIP
The 3 suspicious migration because CMD_BMP and SPLASH_SCREEN
are not activated in these defconfigs:
- trats_defconfig
- s5pc210_universal_defconfig
- trats2_defconfig
Signed-off-by: Patrick Delaunay <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Unused.
Signed-off-by: Andre Heider <[email protected]>
Acked-by: Krzysztof Kozlowski <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
In prepartion to remove CONFIG_DEFAULT_CONSOLE, fold the current users.
Signed-off-by: Andre Heider <[email protected]>
Acked-by: Krzysztof Kozlowski <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
These are all unused.
Signed-off-by: Andre Heider <[email protected]>
Signed-off-by: Heinrich Schuchardt <[email protected]>
Acked-by: Krzysztof Kozlowski <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
These comments are relict for old, now removed config options.
So remove these obsoleted comments too.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-ti
- Minor cleanup on K3 env variables
- Fix OSPI compatible for J721e
- Drop unused property in omap-usb2-phy
- Update Maintainer for am335x-guardian board.
|
|
Use DEFAULT_LINUX_BOOT_ENV to define the standard addresses used in rest
of TI platforms as defined in ti_armv7_common.h
This avoids the standard pitfalls we've had with kernel images and fdt
addresses stomping on each other.
As part of this process, redefine overlayaddr to be dtboaddr (defined
in ti_armv7_common.h for this very purpose) and get rid of the
definition of overlayaddr..
Signed-off-by: Nishanth Menon <[email protected]>
|
|
Now that we dont have any further users of overlayaddr, get rid of it.
Signed-off-by: Nishanth Menon <[email protected]>
|
|
Use DEFAULT_LINUX_BOOT_ENV to define the standard addresses used in rest
of TI platforms as defined in ti_armv7_common.h
This avoids the standard pitfalls we've had with kernel images and fdt
addresses stomping on each other.
As part of this process, redefine overlayaddr to be dtboaddr (defined
in ti_armv7_common.h for this very purpose).. we will get rid of
overlayaddr later in the series.
Signed-off-by: Nishanth Menon <[email protected]>
|
|
Currently we hard-code the number and initial addresses of QEMU's flash
banks, even though our code is perfectly able to gather the same
information from the DTB provided by QEMU.
This is especially annoying, since we have two slightly different
U-Boot configurations ("bare-metal" vs. loaded via Arm Trusted
Firmware), which need to be selected at build time.
Drop the two hard coded alternatives, and use
CONFIG_SYS_MAX_FLASH_BANKS_DETECT instead, which relies on the DTB to
figure out the actual flash configuration at runtime.
Signed-off-by: Andre Przywara <[email protected]>
|
|
Increase CONFIG_SYS_BOOTM_LEN to 64MiB for Linux kernel booting.
Signed-off-by: Stefan Roese <[email protected]>
|
|
This patch adds the board specific configuration (struct) for the
Octeon 3 EBB7304 EVK. This struct is ported from the 2013er Cavium /
Marvell U-Boot repository. Also, the Octeon RAM driver is enabled in
the board defconfig for its usage.
Tested with one and two DIMMs on the EBB7304 EVK (8 & 16 GiB).
Signed-off-by: Stefan Roese <[email protected]>
|
|
Bring in the assorted changes that have been staged in the 'next' branch
prior to release.
Signed-off-by: Tom Rini <[email protected]>
|
|
According to doc/README.distro fdt_addr must not be set when DTB is not
available from hardware. So remove this entry.
Use address 32MB above the start of DRAM for kernel_addr_r. This way
we likely can avoid the self-relocation of the compressed kernel image
before it decompresses to offset 0x8000 from start of DRAM.
Use address 128MB above the start of DRAM for fdt_addr_r, since this is
the maximum location for the end of the kernel. So we avoid overwriting
the DTB.
Use 512k above that for ramdisk_addr_r. This should be enough for the
DTB, rest of DRAM can be used for initrd.
Place boot script / extlinux.conf at offset 0 / 1MB from start of DRAM.
This space is available for processing in U-Boot.
Signed-off-by: Soeren Moch <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Enable the RPC Hyperflash driver on R8A7795,R8A7796,R8A77965
Salvator-X,ULCB and R8A77990 Ebisu. Note that to make the HF
accessible, mainline ATF is mandatory and must be built with
RCAR_RPC_HYPERFLASH_LOCKED=0 . Note that this is intended for
development and testing convenience only and must be disabled
in deployment for platform security reasons.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Nobuhiro Iwamatsu <[email protected]>
|
|
- Bug fixes related to PCIe, pfe, xfi, gpio, reset, vid, env, and usb on
layerscape products
|
|
Signed-off-by: Meenakshi Aggarwal <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2021.01
arm64:
- Support for bigger U-Boot images compiled with PIE
microblaze:
- Extend support for LE/BE systems
zynqmp:
- Refactor silicon ID detection code with using firmware interface
- Add support for saving variables based on bootmode
zynqmp-r5:
- Fix MPU mapping and defconfig setting.
xilinx:
- Minor driver changes: names alignment
- Enable UBIFS
- Minor DT and macros fixes
- Fix boot with appended DT
- Fix distro boot
cmd:
- pxe: Add fixing for platforms with manual relocation support
clk:
- fixed_rate: Add DM flag to support early boot on r5
fpga:
- zynqmppl: Use only firmware interface and enable SPL build
serial:
- uartlite: Enable for ARM systems and support endians
mmc:
- zynq: Fix indentation
net:
- gem: Support for multiple phys
- emac: Fix 64bit support and enable it for arm64
kconfig:
- Setup default values for Xilinx platforms
- Fix dependecies for Xilinx drivers
- Source board Kconfig only when platform is enabled
- Fix FPGA Kconfig entry with SPL
- Change some defconfig values
bindings:
- Add binding doc for vsc8531
|
|
Remove NXP powerpc P5020DS board support as it is no
longer maintained.
Signed-off-by: Priyanka Jain <[email protected]>
|
|
Remove NXP powerpc P1024RDB board support as it is no
longer maintained.
Signed-off-by: Priyanka Jain <[email protected]>
|
|
Remove NXP powerpc P1021RDB board support as it is no
longer maintained.
Signed-off-by: Priyanka Jain <[email protected]>
|
|
Remove NXP powerpc P1020MBG board support as it is no
longer maintained.
Signed-off-by: Priyanka Jain <[email protected]>
|
|
Remove NXP powerpc P1020UTM board support as it is no
longer maintained.
Signed-off-by: Priyanka Jain <[email protected]>
|
|
Remove NXP powerpc P1025RDB board support as it is no
longer maintained.
Signed-off-by: Priyanka Jain <[email protected]>
|
|
Remove NXP powerpc p1023rdb board support as it is no
longer maintained.
Signed-off-by: Priyanka Jain <[email protected]>
|
|
Add the environment 'vscfw_addr' to assign a default address for
vsc7385 firmware uploading.
Signed-off-by: Hou Zhiqiang <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
Increase max gunzip size, required for booting itb recovery images on
uDPU.
Signed-off-by: Vladimir Vid <[email protected]>
[a.heider: adapt to mainline]
Signed-off-by: Andre Heider <[email protected]>
|
|
scan_dev_for_efi is supposed to be called from scan_dev_for_boot.
However this call is missing for ls1028ardb and ls1028aqds boards. As
a result EFI boot doesn’t work. Fix this issue by removing custom
definition of scan_dev_for_boot and use the default definition
instead.
Signed-off-by: Mian Yousaf Kaukab <[email protected]>
Reviewed-by: [email protected]
Reviewed-by: Priyanka Jain <[email protected]>
|
|
PXE and DHCP shouldn't be listed when commands are not enabled that's why
handle it in the same way as is done for Zynq and ZynqMP.
Fixes: ec48b6c991f4 ("arm64: versal: Add support for new Xilinx Versal ACAPs")
Signed-off-by: Michal Simek <[email protected]>
|
|
The patch does sed 's/SPL_FPGA_SUPPORT/SPL_FPGA/g' but also fixing Makefile
and zynqmp.c to simplify if/endif logic in zynqmp.c.
This change is mostly done to be able to use CONFIG_IS_ENABLED macro and
obj-$(CONFIG_$(SPL_)FPGA) in Makefile. For them symbols need to be in sync.
And removing one line from Topic Miami boards which is not needed because
symbol is not enabled via Kconfig.
Signed-off-by: Michal Simek <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
- fix SPL image generation
- fix incorrect console output
- increase malloc_f and malloc_r space to fix LZMA decompression errors
- increase SPI flash clock
Signed-off-by: Mauro Condarelli <[email protected]>
[squashed to one patch, fix commit subject and description]
Signed-off-by: Daniel Schwierzeck <[email protected]>
|
|
Merge in v2020.10-rc5
|
|
This patch moves the the config SYS_MALLOC_LEN to Kconfig
as it is already done for zynq arch in commit 01aa5b8f0503
("Kconfig: Move config SYS_MALLOC_LEN to Kconfig for zynq").
Signed-off-by: Andy Shevchenko <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
