| Age | Commit message (Collapse) | Author |
|---|
|
Extend PHYTEC phyBOARD-i.MX6UL for phyCORE-i.MX6UL SoM (PCL063)
with eMMC on SoM.
CPU: Freescale i.MX6ULL rev1.0 792 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 38C
Reset cause: POR
Model: Phytec phyBOARD-i.MX6ULL-Segin SBC
Board: PHYTEC phyCORE-i.MX6ULL
DRAM: 256 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
In: serial@02020000
Out: serial@02020000
Err: serial@02020000
Net: FEC0
Working:
- Eth0
- i2C
- MMC/SD
- eMMC
- UART (1 & 5)
- USB (host & otg)
Signed-off-by: Parthiban Nallathambi <[email protected]>
|
|
1. Replace usage of "/dev/mmcblk*p*" with a proper UUID of rootfs
partition. This fixes the issue, when MMC controllers are probed in
a different order in U-boot and Linux kernel.
2. Fix legacy USB command (both sdboot and usbboot can be used now).
Acked-by: Marcel Ziswiler <[email protected]>
Signed-off-by: Igor Opaniuk <[email protected]>
|
|
1. Replace usage of "/dev/mmcblk*p*" with a proper UUID of rootfs
partition. This fixes the issue, when MMC controllers are probed in
a different order in U-boot and Linux kernel.
2. Fix legacy USB command (both sdboot and usbboot can be used now).
Acked-by: Marcel Ziswiler <[email protected]>
Signed-off-by: Igor Opaniuk <[email protected]>
|
|
Replace usage of "/dev/mmcblk*p*" with a proper UUID of rootfs
partition. This fixes the issue, when MMC controllers are probed in
a different order in U-boot and Linux kernel.
Acked-by: Marcel Ziswiler <[email protected]>
Signed-off-by: Igor Opaniuk <[email protected]>
|
|
Replace usage of "/dev/mmcblk*p*" with a proper UUID of rootfs
partition. This fixes the issue, when MMC controllers are probed in
a different order in U-boot and Linux kernel.
Acked-by: Marcel Ziswiler <[email protected]>
Signed-off-by: Igor Opaniuk <[email protected]>
|
|
Replace usage of "/dev/mmcblk*p*" with a proper UUID of rootfs
partition. This fixes the issue, when MMC controllers are probed in
a different order in U-boot and Linux kernel.
Acked-by: Marcel Ziswiler <[email protected]>
Signed-off-by: Igor Opaniuk <[email protected]>
|
|
This commit adds initial support for the Toradex Apalis iMX8QM 4GB WB IT
V1.0B module. Unlike the V1.0A early access samples exclusively booting
from SD card, they are now strapped to boot from eFuses which are
factory fused to properly boot from their on-module eMMC. U-Boot
supports either booting from the on-module eMMC or may be used for
recovery purpose using the universal update utility (uuu) aka mfgtools
3.0.
Functionality wise the following is known to be working:
- eMMC, 8-bit and 4-bit MMC/SD card slots
- Gigabit Ethernet
- GPIOs
- I2C
Unfortunately, there is no USB functionality for the i.MX 8QM as of yet.
Signed-off-by: Marcel Ziswiler <[email protected]>
Reviewed-by: Max Krummenacher <[email protected]>
|
|
Enable DM Video support on iMX6Q Novena and fix minor details
to restore previous behavior of the system.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Vagrant Cascadian <[email protected]>
|
|
Enable DM block, DM MMC and DM SATA support on iMX6Q Novena
convert board code to match the DM support.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Vagrant Cascadian <[email protected]>
|
|
Add boot option to boot from fitimage to support verified boot.
The boot script plain text file should be packed into fit blob as
image with name of bootscr.
Signed-off-by: Jun Nie <[email protected]>
|
|
Share configs in mx7 to skip low level init if we are in the case where
OPTEE is loaded already (maybe by ARM Trusted Firmware) and that most of
the low level initialization is already done and that we may/should skip
it doing them here.
Fix the definition detection with size detection to decide whether to skip
it.
Signed-off-by: Jun Nie <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
Enable DM SPI and SF support on DHCOM iMX6 PDK2.
Convert board code to match the DM support.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Ludwig Zenz <[email protected]>
Cc: Stefano Babic <[email protected]>
|
|
Enable DM SATA support on DHCOM iMX6 PDK2.
Convert board code to match the DM support.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Ludwig Zenz <[email protected]>
Cc: Stefano Babic <[email protected]>
|
|
The information about pressed key is relevant in performing correct
update and recovery scenarios via USB pendrive.
This commit modifies envs to provide it.
Signed-off-by: Lukasz Majewski <[email protected]>
|
|
This commit updates envs responsible for using USB pendrive as a
SWUpdate based tool for recovery and update.
Signed-off-by: Lukasz Majewski <[email protected]>
|
|
In certain i.MX devices the encrypted boot image is failing to boot.
According to AN12056 "Encrypted Boot on HABv4 and CAAM Enabled Devices"
it's necessary to pad CSF to 0x2000 and append DEK blob.
In this case the total image size in boot data structure must cover the
entire binary otherwise the dek_blob won't be copied to memory and image
won't be decrypted.
Increase CSF_SIZE to 0x4000 to avoid such issue when booting encrypted
boot images.
Signed-off-by: Breno Lima <[email protected]>
Reviewed-by: Lukasz Majewski <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
Since recovery boot on mmc can get the mmcpart and mmcroot
dynamically, drop the static definitions and handle it
properly.
Tested-by: Shyam Saini <[email protected]>
Signed-off-by: Jagan Teki <[email protected]>
|
|
Provide proper fdtfile env variable value before invoking distro_bootcmd
command.
Signed-off-by: Igor Opaniuk <[email protected]>
|
|
This commit adds initial support for the Toradex Colibri iMX8QXP 2GB WB
IT V1.0B module. Unlike the V1.0A early access samples exclusively
booting from SD card, they are now strapped to boot from eFuses which
are factory fused to properly boot from their on-module eMMC. U-Boot
supports either booting from the on-module eMMC or may be used for
recovery purpose using the universal update utility (uuu) aka mfgtools
3.0.
Functionality wise the following is known to be working:
- eMMC and MMC/SD card
- Ethernet
- GPIOs
- I2C
Unfortunately, there is no USB functionality for the i.MX 8QXP as of
yet.
Signed-off-by: Marcel Ziswiler <[email protected]>
Reviewed-by: Igor Opaniuk <[email protected]>
|
|
- mxsfb DM_VIDEO conversion
- splash fix for DM_VIDEO configurations
- meson HDMI fix for boards without hdmi-supply regulator
|
|
The bulk of these changes are an effort to unify Tegra186 builds with
builds of prior 64-bit Tegra generations. On top of that there are
various improvements that allow data (such as the MAC address and boot
arguments) to be passed through from early firmware to the kernel on
boot.
|
|
Add default SERVERIP address
Enable noncached memory region required by ethernet driver
Add PXE support
Signed-off-by: Christophe Roullier <[email protected]>
|
|
Add all relative flags needed by ENV_IS_IN_SPI_FLASH
Reserved a 256KB partition in NOR to save the U-Boot
environment.
Signed-off-by: Patrice Chotard <[email protected]>
|
|
Add all relative flags needed by ENV_IS_IN_UBI
Signed-off-by: Patrice Chotard <[email protected]>
|
|
This patch configure the default value for mtdids and mtparts
dynamically according the presence of nor and nand in
the board device tree
Signed-off-by: Patrick Delaunay <[email protected]>
Signed-off-by: Christophe Kerello <[email protected]>
Signed-off-by: Patrice Chotard <[email protected]>
|
|
Add the necessary configuration to have NAND and NOR support on ev1 board
for BASIC boot (with SPL) or for TRUSTED boot (with TF-A).
STM32MP> nand info
Device 0: nand0, sector size 256 KiB
Page size 4096 b
OOB size 224 b
Erase size 262144 b
subpagesize 4096 b
options 0x00184200
bbt options 0x00060000
STM32MP> sf probe
SF: Detected mx66l51235l with page size 256 Bytes, erase size 64 KiB, total 64 MiB
Signed-off-by: Patrick Delaunay <[email protected]>
|
|
Boards may not support all the boot target devices in the default list
for Tegra devices. Allow a board to override the list and default to the
standard list only if the board hasn't specified one itself.
Signed-off-by: Thierry Reding <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
This adds a define for CONFIG_SKIP_LOWLEVEL_INIT in the legoev3 config.
On the EV3, U-Boot is loaded into RAM by another bootloader, so we
don't need the lowlevel init in U-Boot.
Signed-off-by: David Lechner <[email protected]>
Signed-off-by: Bartosz Golaszewski <[email protected]>
|
|
This patch adds Microchip MPFS Icicle board support.
For now, NS16550 serial driver is only enabled.
The Microchip MPFS Icicle defconfig by default builds
U-Boot for M-Mode with SMP support.
Signed-off-by: Padmarao Begari <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
Reviewed-by: Lukas Auer <[email protected]>
|
|
The existing default size of 4kB is too small as the default environment
has already nearly that size and defining a single additional environment
variable can exceed the available space.
Signed-off-by: Karsten Merker <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
Extend the driver to build with DM_VIDEO enabled. DTS files
must additionally include 'u-boot,dm-pre-reloc' property in
soc and child nodes to enable driver binding to mxsfb device.
Signed-off-by: Igor Opaniuk <[email protected]>
|
|
For bcm7445 and bcm7260, this patch enables CONFIG_DM_MMC and updates
the bcmstb SDHCI driver to use the new driver model. This allows
removal of SDHCI configuration handling from bcmstb.c, and eliminates
a board removal compile warning.
Signed-off-by: Thomas Fitzsimmons <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <[email protected]>
|
|
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <[email protected]>
Acked-by: Stefano Babic <[email protected]>
|
|
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <[email protected]>
Acked-by: Stefano Babic <[email protected]>
|
|
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <[email protected]>
|
|
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <[email protected]>
Acked-by: Heiko Schocher <[email protected]>
|
|
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <[email protected]>
|
|
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <[email protected]>
Acked-by: Stefano Babic <[email protected]>
|
|
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <[email protected]>
|
|
The first memory location of ${dtbaddr} may be still valid after a warm
restart of the machine and 'fdt addr ${dtbaddr}' doesn't recognize that
the cfgscript didn't run properly and fallback mechanism with copying
the internal fdt ${fdtcontroladdr} to ${dtbaddr} doesn't catch this.
To get sure that we have proper failsafe behaviour we simply zero the
first memory location of ${dtbaddr} for getting sure that the fdt is
invalid if cfgscript didn't run.
Signed-off-by: Hannes Schmelzer <[email protected]>
Signed-off-by: Hannes Schmelzer <[email protected]>
|
|
- Gen3 PCIe driver + enablement on Salvator-X platforms.
- Gen3 recovery SPL used to reload ATF/OpTee/U-Boot instead of minimon.
- SDHI HS400 fixes ported from latest BSP and datasheet.
|
|
Move the main symbol for Freescale Fman Ethernet controller option to
Kconfig. Also migrate the CONFIG_SYS_QE_FMAN_FW_IN_xxx macros and
rename the SPIFLASH one to follow the same format as all of the others.
To do this fully we need to migrate CONFIG_QC, do so.
Signed-off-by: Tom Rini <[email protected]>
|
|
- Add various STM32MP1 fixes for serial, env, clk, board, i2c ...
- Add STM32MP1 DDR driver update:
These update introduce the DDR interactive mode described in:
https://wiki.st.com/stm32mpu/index.php/U-Boot_SPL:_DDR_interactive_mode
This mode is used by the CubeMX: DDR tuning tool.
https://wiki.st.com/stm32mpu/index.php/STM32CubeMX
The DDR interactive mode is NOT activated by default because
it increase the SPL size and slow down the boot time
(200ms wait added).
|
|
This patch removes CONFIG_SYS_DSPI_XX options from
include/configs "m68k" .h board files, since CTAR
registers are now set with default values in the cf_spi
driver initialization, and configurable by devicetree.
Note, these options cannot be totally removed from the
whitelist, since still used from boards using fsl_dspi.c
(mostly arm-based boards).
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Angelo Dureghello <[email protected]>
|
|
Use Kconfig to activate CONFIG_PREBOOT (empty by default).
Signed-off-by: Patrick Delaunay <[email protected]>
|
|
Add arch stm32mp for ENV migration step and drop more
items from include/configs/xxx.h.
Signed-off-by: Patrick Delaunay <[email protected]>
|
|
This patch moves the the config SYS_MALLOC_LEN to
Kconfig as it is already done for zynq arch in
commit 01aa5b8f0503 ("Kconfig: Move config
SYS_MALLOC_LEN to Kconfig for zynq")
Signed-off-by: Patrick Delaunay <[email protected]>
|
|
commit 58c3e62040be ("armv8: lx2160ardb : Add support for LX2160ARDB
platform") brought a new boards support with redundancy in the config.h.
One of them is CONFIG_CMDLINE_EDITING which is removed by this change.
Cc: Priyanka Jain <[email protected]>
Cc: Peng Ma <[email protected]>
Cc: Prabhakar Kushwaha <[email protected]>
Signed-off-by: Andy Shevchenko <[email protected]>
Reviewed-by: Prabhakar Kushwaha <[email protected]>
|
|
esbc_validate command will not be executed if “load” command for its
header fails and will further execute the source command for bootscript,
without its validation and boot process continues.
To halt the boot process in case secure boot header is not loaded
successfully, esbc_validate command is invoked separately after “load”
command. The secure boot validation of the bootscript header will fail
(if header is not loaded) and halts the boot process, which prevent source
command from execution.
Signed-off-by: Vinitha V Pillai <[email protected]>
Signed-off-by: Udit Agarwal <[email protected]>
Reviewed-by: Prabhakar Kushwaha <[email protected]>
|
