| Age | Commit message (Collapse) | Author |
|---|
|
Migrate MMC and SATA to using driver model.
While at it also enable SCSI driver model.
Signed-off-by: Marcel Ziswiler <[email protected]>
|
|
Migrate I2C to using driver model.
Signed-off-by: Marcel Ziswiler <[email protected]>
|
|
Remove obsolete USB_GADGET_MASS_STORAGE configuration.
Signed-off-by: Marcel Ziswiler <[email protected]>
Reviewed-by: Igor Opaniuk <[email protected]>
|
|
Move console in env from header file to defconfig.
While at it also update copyright year and remove spurious comments and
new lines.
Signed-off-by: Marcel Ziswiler <[email protected]>
|
|
Fix the NFS commands which used `set' to instead use `setenv'.
Signed-off-by: Ian Ray <[email protected]>
|
|
New boot command introduced to automate network booting.
Signed-off-by: Joonas Aijala <[email protected]>
Signed-off-by: Ian Ray <[email protected]>
|
|
Specific ARP timeout sometimes causes ARP timeout during nfs loading
of the fitImage.
Signed-off-by: Joonas Aijala <[email protected]>
Signed-off-by: Ian Ray <[email protected]>
|
|
Use MMC device model, and remove USDHC pin configuration code since the
pinctrl driver is used.
Signed-off-by: Ian Ray <[email protected]>
|
|
Use MMC device model, and remove USDHC pin configuration code since the
pinctrl driver is used.
Signed-off-by: Ian Ray <[email protected]>
|
|
Signed-off-by: Lukasz Majewski <[email protected]>
|
|
Signed-off-by: Lukasz Majewski <[email protected]>
|
|
The BK4's config file has changed since its initial posting to main line.
This commit reflects those changes.
Signed-off-by: Lukasz Majewski <[email protected]>
|
|
Signed-off-by: Lukasz Majewski <[email protected]>
Reviewed-by: Marcel Ziswiler <[email protected]>
|
|
This commit updates BK4's and PCM052's config files to support as much
as possible device tree and model in u-boot.
Moreover, remove CONFIG_* from pcm052.h (as those are now in
bk4|pcm052_defconfig)
Signed-off-by: Lukasz Majewski <[email protected]>
|
|
- mt76xx: add USB support, small fixes
- ath79: small fixes, add support for QCA9563 SoC and AP152 reference board
- mscc: small fixes, add network support for JR2 and ServalT SoCs
- bmips: small fixes, enable more drivers for ARM specific BCM6858 and BCM63158 SoCs
- MIPS: fix redundant relocation of initrd images
|
|
stm32 patches for v2019.07-rc1
- Add trusted boot with TF-A for stm32mp1
- stm32mp1 dts files sync'ed with Linux version
- add STM32MP1 Discovery boards (DK1 and DK2)
- add STMFX gpio expander driver
- misc improvement for stm3mp1 supports
- rename stpmu1 to stpmic1 (official name)
- stm32_qspi: move to exec_op (spi nor driver for stm32 mpu and mcu)
- add STM32 FMC2 NAND flash controller driver
|
|
- Misc dts files sync'ed with Linux version (Chris)
- Orion watchdog fix (Chris)
- kwbimage changed to also support Marvell bin_hdr binary (Chris)
- Add DM support to enable CONFIG_BLK for sata_mv (Stefan)
- Enable BLK on multiple platforms (Stefan)
- Misc minor fixes to AXP theadorable board (Stefan)
- Correct logic for DM_SCSI + unconverted drivers check (stefan)
- Misc changes to kirkwood to enable DM_USB here (Chris)
- Change ahci_mvebu to enable usage on A38x (Baruch)
- Update the kirkwood entry in git-mailrc (Baruch)
- Misc minor improvements (turris, documentation) (Baruch)
- Enhance sata_mv to support Kirkwood as well (Michael)
- Add wdt command (Michael)
- Add Marvell integrated CPUs (MSYS) support with DB-XC3-24G4XG
board support (Chris)
|
|
Shrink the environment size for 3 reasons:
- reading the environment it is slow, therefore having a smaller env
improves the speed.
- usually in the environment there are only few variables, therefore
the enviromnent is almost empty.
- because the same image can run on different boards which may have
different flashes with different page sizes, the CONFIG_ENV_SECT_SIZE
can't be change, it is set to least common multiple of the page sizes.
Adding this change improves the boot time. Before update for reading the
entire environment it took ~850 msec, after the change it takes ~40 msecs.
Signed-off-by: Horatiu Vultur <[email protected]>
|
|
Add network driver for Microsemi Ethernet switch.
It is present on Jaguar2 SoCs.
Reviewed-by: Daniel Schwierzeck <[email protected]>
Signed-off-by: Horatiu Vultur <[email protected]>
|
|
QCA9563 is CPU used on AP152 board :
Clock speed : 750 MHz ,
Arch : Mips 74Kc,
Eth : SGMII interface,
MIMO config : 3 * 3 450M,
2 * USB 2.0,
Signed-off-by: Rosy Song <[email protected]>
Changes for v2:
- coding style cleanup
- remove ununsed flash chip in defconfig
- enable automatic icache / dcache size in defconfig
Changes for v3:
- add detailed information for qca956x in commit message
Changes for v4:
- remove pre-configured network settings in ap152.h
Changes for v5:
- coding style cleanup
|
|
Add configuration useful for test
- FIT support
- MEMTEST
- DFU
- CACHE
- TIME
- TIMER
Signed-off-by: Patrick Delaunay <[email protected]>
|
|
Update the memory layout to be aligned with other platform and avoid
overlap with 32MB Linux kernel (multiv7 image).
+ Kernel => 32MiB offset = 0xC2000000
and increase the bootm size to 32MiB
+ FDT => 64MiB offset = 0xc4000000
+ SCRIPT => 65Mib offset = 0xc4100000
+ PXESCRIPT => 66Mib offset = 0xc4200000
+ SPLASHIMAGE => 67Mib offset = 0xc4300000
+ RAMDISK => 68Mib offset = 0xc4400000
(not limited size)
In sources/boot/u-boot/doc/README.distro
+ kernel_addr_r: A size of 16MB for the kernel is likely adequate.
+ pxefile_addr_r: A size of 1MB for extlinux.conf is more than adequate.
+ fdt_addr_r: A size of 1MB for the FDT/DTB seems reasonable.
+ ramdisk_addr_r: It is recommended that this location be highest in RAM
out of fdt_addr_, kernel_addr_r, and ramdisk_addr_r,
so that the RAM disk can vary in size and use any
available RAM.
+ pxefile_addr_r: A size of 1MB for extlinux.conf is more than adequate.
+ scriptaddr: A size of 1MB for extlinux.conf is more than adequate.
For suggestions on memory locations for ARM systems, you must follow
the guidelines specified in Documentation/arm/Booting
in the Linux kernel tree.
And in sources/linux-stm32mp/Documentation/arm/Booting
The zImage may also be placed in system RAM and called there. The
kernel should be placed in the first 128MiB of RAM. It is recommended
that it is loaded above 32MiB in order to avoid the need to relocate
prior to decompression, which will make the boot process slightly
faster.
Signed-off-by: Patrick Delaunay <[email protected]>
|
|
Clearly separate bootcmd for stm32mp1 board
(bootcmd_stm32mp) and preboot management.
That solve issue for fastboot continue command.
Signed-off-by: Patrick Delaunay <[email protected]>
|
|
Add support of trusted boot, using TF-A as first stage bootloader,
The boot sequence is
BootRom >=> TF-A.stm32 (clock & DDR) >=> U-Boot.stm32
The TF-A monitor provides secure monitor with support of SMC
- proprietary to manage secure devices (BSEC for example)
- PSCI for power
The same device tree is used for STMicroelectronics boards with
basic boot and with trusted boot.
Signed-off-by: Patrick Delaunay <[email protected]>
|
|
The ISW_ENTRY_ADDR Kconfig option under mach-omap2 isn't a SoC specific
notion but rather "where is our previous stage loaded in memory?"
option. Make use of this on ARCH_KEYSTONE rather than SPL_TEXT_BASE for
our HS builds that are not using SPL anyhow.
Cc: Vitaly Andrianov <[email protected]>
Cc: Andrew F. Davis <[email protected]>
Cc: Lokesh Vutla <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Lokesh Vutla <[email protected]?
|
|
Now that NAND is supported on DRA71x include various NAND environment
settings
Signed-off-by: Faiz Abbas <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
In order to fully support SPL_OF_CONTROL, we need BSS to be a bit
larger. This patch relocates BSS to SDRAM instead of SRAM which
is similar to how ARMv7 boards (like OMAP2+) do it.
This means two new variables are required:
CONFIG_SPL_BSS_START_ADDR set to DAVINCI_DDR_EMIF_DATA_BASE
CONFIG_SPL_BSS_MAX_SIZE is set to 0x1080000 which is 1 byte
before the location where U-Boot will load.
Signed-off-by: Adam Ford <[email protected]>
|
|
Add support for the Bosch Guardian board.
CPU : AM335X-GP rev 2.1
Model: Bosch AM335x Guardian
I2C: ready
DRAM: 256 MiB
NAND: 512 MiB
MMC: OMAP SD/MMC: 0
Signed-off-by: Sjoerd Simons <[email protected]>
Signed-off-by: Martyn Welch <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Reviewed-by: Felix Brack <[email protected]>
|
|
The DB-XC3-24G4XG is a switch development board from Marvell. It can
either use and external CPU card such as the db-88f6820-amc or the
internal CPU that is integrated into the switch.
Add support for running U-Boot on the internal CPU and enable the USB,
SPI and NAND peripherals. For now this needs the bin_hdr from the
Marvell U-Boot for this board.
Signed-off-by: Chris Packham <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Switch from legacy IDE driver to sata_mv driver.
Signed-off-by: Michael Walle <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Signed-off-by: Baruch Siach <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Following commits abe66b1b5dec ("Convert CONFIG_ENV_SPI_* to Kconfig")
and 14453fbfadc2f ("Convert CONFIG_SF_DEFAULT_* to Kconfig") remove
dandling comment lines and empty #ifdef sections.
Cc: Patrick Delaunay <[email protected]>
Signed-off-by: Baruch Siach <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Merge drivers/soc/keystone/ into drivers/soc/ti/
and convert CONFIG_TI_KEYSTONE_SERDES into Kconfig.
Signed-off-by: Vignesh R <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
- Various rmobile fixes
|
|
LibreTech AC is a single board computer manufactured by Libre Technology
with the following specifications:
- Amlogic S805X ARM Cortex-A53 quad-core SoC @ 1.2GHz
- ARM Mali 450 GPU
- 512MiB DDR4 SDRAM
- 10/100 Ethernet
- HDMI 2.0 4K/60Hz display
- 40-pin GPIO header
- 4 x USB 2.0 Host
- eMMC, SPI NOR Flash
- Infrared receiver
The u-boot specific code is the same as the P212 support,
so use the P212 board support code with a distinct defconfig
and config include files.
Signed-off-by: Neil Armstrong <[email protected]>
|
|
Increase the USB power good delay on Alt, this is required with
certain USB sticks, otherwise they might not be detected.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Nobuhiro Iwamatsu <[email protected]>
|
|
The GARDENA smart Gateway boards are equipped with an Atmel / Microchip
AT91SAM9G25 SoC and with 128 MiB of RAM and 256 MiB of NAND storage.
This patch adds support for this board including SPL support. Therefore
the AT91Boostrap is not needed on this platform any more.
Signed-off-by: Stefan Roese <[email protected]>
Cc: Heiko Schocher <[email protected]>
Cc: Andreas Bießmann <[email protected]>
Cc: Eugen Hristev <[email protected]>
Reviewed-by: Heiko Schocher <[email protected]>
|
|
This patch adds the necessary defines to the Siemens AT91SAM based
boards (smartweb, corvus and taurus) to generate the combined binary
image with SPL and main U-Boot image combined (u-boot-with-spl.bin).
Signed-off-by: Stefan Roese <[email protected]>
Cc: Heiko Schocher <[email protected]>
Cc: Andreas Bießmann <[email protected]>
Cc: Eugen Hristev <[email protected]>
Reviewed-by: Heiko Schocher <[email protected]>
Tested on the taurus board:
Tested-by: Heiko Schocher <[email protected]>
|
|
Migrate the following options to CONFIG_DM:
CONFIG_DM_GPIO
CONFIG_DM_MMC
CONFIG_DM_ETH
CONFIG_DM_SERIAL
CONFIG_DM_USB
Signed-off-by: Ilko Iliev <[email protected]>
|
|
Fixes for 2019.04
- fix bashism for MX8
- fix ethernet for MX53
- fix docs for i.MX8
|
|
Signed-off-by: Lukasz Majewski <[email protected]>
|
|
After running tools/moveconfig.py it turned out that for various boards
there are an empty #ifdef statements.
Remove them to clean u-boot source code.
Signed-off-by: Lukasz Majewski <[email protected]>
|
|
Minor fixes for the Alt board and PHY use on Gen2.
|
|
With UUID support, the root can now point to UUID. This makes
swiching between mmc 0 and mmc 1 easier by simplying changing
mmcdev between 0 and 1. From there, the scripts handle the rest.
Signed-off-by: Adam Ford <[email protected]>
|
|
Signed-off-by: Stefano Babic <[email protected]>
|
|
Commit d245059ff797 ("ARM: rmobile: rcar-gen3: Activate bootm_size")
only fixed the superfluous CONFIG_SYS_BOOTMAPSZ for R-Car Gen3, even
though it listed all affected boards. Apply the same fix to Gen2.
Signed-off-by: Marek Vasut <[email protected]>
Fixes: d245059ff797 ("ARM: rmobile: rcar-gen3: Activate bootm_size")
Cc: Eugeniu Rosca <[email protected]>
|
|
The FIT image is loaded to 0x8700_0000 followed by extracting from that
several large images also into the 0x8x00_0000 range. Large images
can end up overwriting the FIT image as it is being extracted from.
Move the FIT load address clear out to 0x9000_0000, this will require
a board to have at least 256MB of DRAM, if less then more careful
planning will be required for that platform.
Signed-off-by: Andrew F. Davis <[email protected]>
|
|
On AXS10x boards we have non-standard NAND controller
which was never really used a lot as there're other much more
convenient [as they are standard & removable] persistent media
like SD-card and USB mass storage.
Moreover after recent changes we face with some NAND controller
runtime issues. So instead of keeping support of yet another
non-standard peripheral we're dropping its support for good.
Signed-off-by: Eugeniy Paltsev <[email protected]>
Signed-off-by: Alexey Brodkin <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_ENV_SPI_BUS
CONFIG_ENV_SPI_CS
CONFIG_ENV_SPI_MAX_HZ
CONFIG_ENV_SPI_MODE
Most of time these value are not needed, CONFIG_SF_DEFAULT
with same value is used, so I introduced CONFIG_USE_ENV_SPI_*
to force the associated value for the environment.
Signed-off-by: Patrick Delaunay <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_DEFAULT_SPI_BUS
CONFIG_DEFAULT_SPI_MODE
Signed-off-by: Patrick Delaunay <[email protected]>
|
