| Age | Commit message (Collapse) | Author |
|---|
|
Currently, it isn't possible to build clock drivers for more than one
platform due to how the msm_enable() and msm_set_rate() callbacks are
implemented.
Extend qcom_clk_data to include function pointers for these and convert
all platforms to use them.
Previously, clock drivers relied on include/configs/<board.h> to include the
board specific sysmap header, however as most of the header contents are clock
driver related, import the contents directly into each clock driver and
remove the header. The only exception here is the dragonboard820c board file
which includes some pinctrl macros, those are also inlined.
Reviewed-by: Sumit Garg <[email protected]>
Signed-off-by: Caleb Connolly <[email protected]>
[caleb: remove additional sysmap-sdm845.h mention]
|
|
The default set of environment variables from CFG_EXTRA_ENV_SETTINGS
has been moved to a separate file - board/liebherr/xea/xea.env
Adjustments done:
- fitImage support
- SPI-NOR layout re-organization
Signed-off-by: Lukasz Majewski <[email protected]>
|
|
In case CONSOLE_MUX and SYS_CONSOLE_IS_IN_ENV are enabled, the console
stdin, stdout, stderr must be defined in environment. Define the default
settings to fix the following warning on boot:
"
In: No input devices available!
Out: No output devices available!
Err: No error devices available!
"
Sort the default environment as well.
Signed-off-by: Marek Vasut <[email protected]>
|
|
In case CONSOLE_MUX and SYS_CONSOLE_IS_IN_ENV are enabled, the console
stdin, stdout, stderr must be defined in environment. Define the default
settings to fix the following warning on boot:
"
In: No input devices available!
Out: No output devices available!
Err: No error devices available!
"
Sort the default environment as well.
Signed-off-by: Marek Vasut <[email protected]>
|
|
Maxim Uvarov <[email protected]> says:
Add small net fixes prior lwip patches.
|
|
Use device specific naming for variables so as to not overlap
with common function names.
Signed-off-by: Maxim Uvarov <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Reviewed-by: Peter Robinson <[email protected]>
|
|
Add support for the Variscite VAR-SOM-IMX93 evaluation kit. The SoM
consists of an NXP iMX93 dual A55 CPU. The SoM is mounted on a Variscite
Symphony SBC.
Signed-off-by: Mathieu Othacehe <[email protected]>
|
|
fdt_addr variable is the location in flash of the device tree blob [1], it
does not exist for verdin-imx8mm.
Because of this the bootefi command fails unless the optional
`[fdt address]` parameter is passed on the command line,
bootefi.c:efi_install_fdt() assumes that `fdt_addr` is valid when
present.
Fix this removing fdt_addr from the U-Boot environment.
[1] doc/usage/environment.rst
Signed-off-by: Francesco Dolcini <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
We need to include <config.h> directly when a file needs to have
something such as CFG_SYS_SDRAM_SIZE referenced as this file is not
automatically globally included and is most commonly indirectly included
via common.h. Remove most cases of arc including config.h directly, but
add it where needed. Further clean up the tb100 board config.h file so
that we don't rely on config.h being included there for a value used in
a single place.
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
In general terms, we -include include/linux/kconfig.h and so normal
U-Boot code does not need to also #include it. However, for code which
is shared with userspace we may need to add it so that either our full
config is available or so that macros such as CONFIG_IS_ENABLED() can be
evaluated. In this case make sure that we guard these includes with a
test for USE_HOSTCC so that it clear as to why we're doing this.
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Drop the pinmux setup in the board in favor of setting it up in
the device tree. Device tree nodes match nodes used for the Linux
device tree and are set according to the service manual.
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
Julien Masson <[email protected]> says:
This patch series add the support for the MediaTek MT8365 EVK Board [1].
Most of the code have been copied/adapted from Linux tag v6.7-rc2.
For now we only enable/test these features:
Boot, UART, Watchdog and MMC.
[trini: This includes two clocks not listed in the Linux binding, which
needs resyncing later]
|
|
This patch adds basic support for MediaTek MT8365 SoC.
The dtsi has been copied from Linux source code tag v6.7-rc2.
(commit 9b5d64654ea8f51fe1e8e29ca1777b620be8fb7c)
Signed-off-by: Julien Masson <[email protected]>
|
|
The AEM and Juno FVPs (Fixed Virtual Platforms) support a VirtIO
disc interface. Adding VIRTIO to the list of boot devices allows
these FastModel platforms to boot from 'disc' in the same way
the hardware counterpart can boot from SATA or USB.
This is a NOP if CONFIG_CMD_VIRTIO is not enabled, so no impact
on Juno hardware (which is built with vexpress_aemv8a_juno_defconfig)
Signed-off-by: Robert Catherall <[email protected]>
Reviewed-by: Andre Przywara <[email protected]>
|
|
into next
- VisionFive2: Enable CONFIG_SYSRESET
- StarFive: Modify starfive timer driver
- AMD/Xilinx: Add MicroBlaze V support
- Unmatched: Migrate to text environment
|
|
Prepare v2024.01-rc5
|
|
Migrate to the new environment format and drop most of the config.h.
Signed-off-by: Yong-Xuan Wang <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
MicroBlaze V is new AMD/Xilinx soft-core 32bit RISC-V processor IP.
It is hardware compatible with classic MicroBlaze processor.
The patch contains initial wiring and configuration for initial HW design
with memory, cpu, interrupt controller, timers and uartlite console
(interrupt controller is listed but U-Boot is not using it).
Provided DT is just describing one configuration and should be taken only
as example.
Signed-off-by: Michal Simek <[email protected]>
Reviewed-by: Leo Yu-Chi Liang <[email protected]>
Reviewed-by: Padmarao Begari <[email protected]>
|
|
The base address of extended DDR does not change across the K3 family.
Setting this per SoC is not needed. Remove this definition to help
remove the last bits from K3 include/configs/*.h files.
Signed-off-by: Andrew Davis <[email protected]>
|
|
Display the STMicroelectronics logo with features VIDEO_LOGO and
SPLASH_SCREEN on stm32f469-disco board.
Signed-off-by: Dario Binacchi <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
|
|
Technexion PICO-IMX7 SoM is supporting USDHC3 (eMMC or micro SD on SoM)
and USDHC1 (SD on carrier board) to use on any carrier board like
PICO-NYMPH. Based on the U-Boot version from Technexion it adds
baseboard SD card boot detect to able to boot from selected USDHC1
or USDHC3 boot devices.
Signed-off-by: Benjamin Szőke <[email protected]>
Tested-by: Fabio Estevam <[email protected]>
|
|
The "booti" command to load arm64 Linux kernels supports automatic
decompression of zipped kernel images, but relies on some environment
variables to point to usable buffer RAM.
Add those variables and let them point to some default values, that
should cover most use-cases.
Signed-off-by: Arnaud Ferraris <[email protected]>
|
|
Add support for the Polyhex Debix Model A SBC board.
It is an industrial grade single board computer based on
NXP's i.MX 8M Plus.
Currently supported interfaces are:
- Serial console
- Micro SD
- eQOS and FEC Ethernet
imx8mp-debix-model-a.dts is taken from Linux 6.3.
Signed-off-by: Gilles Talis <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
|
|
Later versions of Colibri iMX7D V1.1B modules use a "new" SoC fusing. The
difference lies in whether we enable the boot ROM to use the eMMC reset
signal. Depending on the SoC fuse, the boot ROM configures this pin as a
GPIO output to drive the reset signal. Our eMMC vs NAND detection
currently only sets that signal to a GPIO without explicitly setting any
direction. Previously, by default, it was set as an input. As the boot ROM
now configures it as an output, we receive a value of zero instead of one,
indicating the absence of the pull-up on eMMC modules.
To fix this, set the SION bit, allowing the reading back of the value
even if it is configured as an output by the boot ROM. It's important to
note that with the new SoC fusing, we now read back what the boot ROM
drives rather than the real value caused by the pull-up resistor. However,
if it were ever driven low, the eMMC would permanently be reset.
In addition, remove hard-coded variant in the eMMC build case as since the
commit 0c39564d0281 ("toradex: colibri_imx7: Enable nand/emmc detection
and set boot variant") will anyways always get overridden by the detection
routing in board code.
Fixes: 0c39564d ("toradex: colibri_imx7: Enable nand/emmc detection and set boot variant")
Signed-off-by: Marcel Ziswiler <[email protected]>
Signed-off-by: Hiago De Franco <[email protected]>
|
|
device tree overlay support requires fdtoverlay_addr_r to be set
before
~~~~~~
Invalid fdtoverlay_addr_r for loading overlays
after
~~~~~
Retrieving file: /boot/overlay/rtc-ds3231.dtbo
Signed-off-by: John Clark <[email protected]>
Reviewed-by: Leo Yu-Chi Liang <[email protected]>
|
|
This is a hacky way to have this file included in all source files that
include common.h, instead just include from the files that need it.
Signed-off-by: Andrew Davis <[email protected]>
|
|
These are leftover definitions. While here cleanup some leftover comments.
Signed-off-by: Andrew Davis <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Draco is a family of 3 boards: thuban, rastaban & etamin. Rename all
targets of the family adding the draco- prefix to increase readibility
and simplify future commits about concerning all boards of the family.
The name draco was initially used for the first target. It's deprecated
since a 2nd target was introduced. Unfortunately the draco target was
copied to the thuban target instead to be renamed. Remove it to save
unnecessary maintenance effort.
Signed-off-by: Enrico Leto <[email protected]>
|
|
Prepare v2024.01-rc3
|
|
Adjust mem layout, providing more space for linux kernel image.
This fixes the problem:
ERROR: FDT image overlaps OS image (OS=0x30000000..0x32580000)
Signed-off-by: Igor Opaniuk <[email protected]>
Reviewed-by: Sam Protsenko <[email protected]>
|
|
Add initial support for STM32MP2 SoCs family.
SoCs information are available here :
https://www.st.com/content/st_com/en/campaigns/microprocessor-stm32mp2.html
Migrate all MP1 related code into stm32mp1/ directory
Create stm32mp2 directory dedicated for STM32MP2 SoCs.
Common code to MP1, MP13 and MP25 is kept into
arch/arm/mach-stm32/mach-stm32mp directory :
- boot_params.c
- bsec
- cmd_stm32key
- cmd_stm32prog
- dram_init.c
- syscon.c
- ecdsa_romapi.c
For STM32MP2, it also :
- adds memory region description needed for ARMv8 MMU.
- enables early data cache before relocation.
During the transition before/after relocation, the MMU, initially setup
at the beginning of DDR, must be setup again at a correct address after
relocation. This is done in enables_caches() by disabling cache, force
arch.tlb_fillptr to NULL which will force the MMU to be setup again but
with a new value for gd->arch.tlb_addr. gd->arch.tlb_addr has been
updated after relocation in arm_reserve_mmu().
Signed-off-by: Patrice Chotard <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
|
|
- Fix some issues Coverity has reported, update MAINTAINERS file,
another bootstd fix, typo fix in error message, gitignore fix and
update TI's URL in many places.
|
|
Replace instances of http://www.ti.com with https://www.ti.com
Signed-off-by: Nishanth Menon <[email protected]>
|
|
QuartzPro64 is a Rockchip RK3588 based SBC by Pine64.
UART and boot over SD/eMMC/RJ45 are tested to work.
Linux commits from next-20231013:
8152d3d070a9 ("arm64: dts: rockchip: Add QuartzPro64 SBC device tree")
Signed-off-by: Tom Fitzhenry <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
Cc: Eugen Hristev <[email protected]>
Cc: Jonas Karlman <[email protected]>
Cc: Ondrej Jirman <[email protected]>
|
|
The migration deadline for moving to DM_SCSI was v2023.04. A further
reminder was sent out in August 2023 to the remaining platforms that had
not migrated already, and that a few more over the line (or configs
deleted).
With this commit we:
- Rename CONFIG_DM_SCSI to CONFIG_SCSI.
- Remove all of the non-DM SCSI code. This includes removing other
legacy symbols and code and removes some legacy non-DM AHCI code.
- Some platforms that had previously been DM_SCSI=y && SCSI=n are now
fully migrated to DM_SCSI as a few corner cases in the code assumed
DM_SCSI=y meant SCSI=y.
Signed-off-by: Tom Rini <[email protected]>
|
|
Move the DEFAULT_ENV_IS_RW to Kconfig for easier configuration.
Hence, add the CONFIG_DEFAULT_ENV_IS_RW config to the defconfig files
to allow enabling them for armada boards.
Signed-off-by: Algapally Santosh Sagar <[email protected]>
Signed-off-by: Venkatesh Yadav Abbarapu <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michal Simek <[email protected]>
|
|
This adds support for the Inteno XG6846 board based on the
Broadcom MIPS 6328 SoC.
The default boot will read a uImage from flash and boot it.
Reviewed-by: Daniel Schwierzeck <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
USB_DFU was added in meson64.h but is missing in libretech-ac.h,
fix this to enable DFU RAM boot for libretech-ac.
Fixes 4aa027b3f8 ("configs: meson64: add alternate USB DFU boot target")
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Neil Armstrong <[email protected]>
|
|
Convert refresh USB to enter console. Transformers have full size
USB and a dock keyboard so access to U-Boot console would be handy.
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
U-boot initially loads the kernel image to the kernel_addr_r, and
subsequently relocates it to memory address 0x80200000. Setting
kernel_addr_r to 0x80200000 can eliminate one copy operation.
Signed-off-by: Yong-Xuan Wang <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
enable distro_bootcmd
Signed-off-by: Abdellatif El Khlifi <[email protected]>
Signed-off-by: Rui Miguel Silva <[email protected]>
|
|
There are two kinds of NOR flash layout for the Developerbox.
Capsule update for the old layout is no longer available since
it has small capacity for secure world images and can not
house the TA such as fTPM.
This commit removes the definition related to the obsolete
NOR flash layout for the UEFI capsule update.
Signed-off-by: Masahisa Kojima <[email protected]>
Acked-by: Jassi Brar <[email protected]>
Reviewed-by: Ilias Apalodimas <[email protected]>
|
|
Add uart baud rate table to arbel(npcm8xx) and poleg(npcm7xx)
Signed-off-by: Jim Liu <[email protected]>
[trini: Rework slightly]
Signed-off-by: Tom Rini <[email protected]>
|
|
This was lost in refactoring while some users of the IOT2050 expect it
to work: Make sure that up to 3 USB storage devices are probed.
Fixes: 53873974a4b0 ("include: armv7: Enable distroboot across all configs")
Signed-off-by: Jan Kiszka <[email protected]>
Reviewed-by: Heinrich Schuchardt <[email protected]>
|
|
Add MMC disk to FVP's BOOT_TARGET_DEVICES. This allows the user to boot
from MMC devices.
Signed-off-by: Wei Chen <[email protected]>
Signed-off-by: Qi Feng <[email protected]>
Reviewed-by: Linus Walleij <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-amlogic
- Fix environment saving for new Android boot features on vim3*_android
- Add SPIFC support for Amlogic A1
- Add DFU RAM boot step when booting over USB
|
|
Add boot over DFU RAM as an alternate to running script at
a fixed address like done today.
The main culprit is that it's not possible to do that
on G12A/Sm1 platforms due to changes in the USB boot protocol.
With this, U-Boot will present a DFU device with a ram slot where
the Host could write a fitImage or legacy U-Boot image, then with the
detach command boot will continue trying to boot the uploaded image.
Signed-off-by: Neil Armstrong <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Neil Armstrong <[email protected]>
|
|
In order to reuse addresses for DFU RAM, define them separately,
it's cleaner and will be easier to override.
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Neil Armstrong <[email protected]>
|
|
Enable bootstd for Zyxel NSA310S board, and remove distroboot.
Signed-off-by: Tony Dinh <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Enable bootstd for Pogo V4 board, and remove distroboot.
Signed-off-by: Tony Dinh <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
