| Age | Commit message (Collapse) | Author |
|---|
|
On AM437x-GP Evm there is 2GB of DDR3 memory available as stated in
AM437x GP EVM HardwareUser's guide http://www.ti.com/lit/ug/spruhw7/spruhw7.pdf.
But MAX_RAM_BANK_SIZE is defined as 1GB.
Fixing MAX_RAM_BANK_SIZE to 2GB on AM43xx.
Reported-by: Shivasharan Nagalikar <[email protected]>
Signed-off-by: Lokesh Vutla <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Enable booting from NAND on the am437xx-evm.
Signed-off-by: Tom Rini <[email protected]>
Signed-off-by: Roger Quadros <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Use the correct partition names from with the Device Tree blob
and the kernel is picked up. Also use partition name instead of
number for the root filesystem in the kernel boot arguments.
Signed-off-by: Roger Quadros <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
We almost always use UBIFS for user accessible NAND file systems and
the UBIFS file system might contain more than one volume within the
single NAND partition. The last NAND partition is therefore more
appropriately named as "NAND.file-system" instead of "NAND.rootfs"
The Linux kernel (as of v3.16) also uses "NAND.file-system" to name the
last NAND partition. This patch makes the partition name consistent
between u-boot and the kernel.
Signed-off-by: Roger Quadros <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
|
|
Enable IO delay recalibration sequence.
Signed-off-by: Lokesh Vutla <[email protected]>
Signed-off-by: Nishanth Menon <[email protected]>
|
|
Enabling IO delay recalibration sequence for DRA7 EVM.
UART and I2C are configured before IO delay recalibration sequence
as these are used earlier and safe to use.
Signed-off-by: Lokesh Vutla <[email protected]>
Signed-off-by: Nishanth Menon <[email protected]>
|
|
Move this over to Kconfig and tidy up.
Signed-off-by: Simon Glass <[email protected]>
|
|
|
|
Due to absence of CONFIG_SYS_64BIT_LBA, u-boot-sunxi currently has
no support for the (GPT) partioning scheme of large disks > 2TB.
While the AHCI driver seems to handle this nicely, the problem is
that lbaint_t values get truncated to 32-bit.
This patch sets CONFIG_SYS_64BIT_LBA from sunxi_common.h for all
SoCs that support AHCI (CONFIG_SUNXI_AHCI).
Signed-off-by: Bernhard Nortmann <[email protected]>
Reviewed-by: Hans de Goede <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
|
|
|
|
Signed-off-by: Andreas Bießmann <[email protected]>
|
|
Signed-off-by: Andreas Bießmann <[email protected]>
|
|
Signed-off-by: Andreas Bießmann <[email protected]>
|
|
Signed-off-by: Andreas Bießmann <[email protected]>
|
|
Signed-off-by: Andreas Bießmann <[email protected]>
|
|
We need to match the device tree in the FIT with the U-Boot model so we
can automatically select the right device tree. Also adjust the load address
so that the device tree is not in the way when a zImage kernel tries to
extract itself.
Signed-off-by: Simon Glass <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
Bring these in if they are provided by the board.
Signed-off-by: Simon Glass <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
When setting up large environment variables we can exceed 16 arguemnts.
Increase this to avoid problems.
Signed-off-by: Simon Glass <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
Enable the EC and keyboard, using the SPI bus.
The EC driver requires a particular format and a deactivation delay. Also
U-Boot does not support interrupts.
For now, adjust the device tree to comply. At some point we should tidy
this up to support interrupts and make tegra and exynos use the same setup.
Signed-off-by: Simon Glass <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
This requires a change to stdin to include the 'cros-ec-keyb' input device.
Put this in the common file, enabled by the relevant CONFIG.
Signed-off-by: Simon Glass <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
Add PRE_CONSOLE_BUFFER support to display early boot messages over HDMI.
Signed-off-by: Soeren Moch <[email protected]>
|
|
Signed-off-by: Soeren Moch <[email protected]>
|
|
Commit a380ce6e9698257c4e8be4c0711b09c90a8febff removed CONFIG_FAT_WRITE
from novena.h , so Novena lost ability to write FAT partitions. Add this
functionality back.
Signed-off-by: Marek Vasut <marex at denx.de>
Cc: Peter Robinson <pbrobinson at gmail.com>
Cc: Stefano Babic <sbabic at denx.de>
|
|
AM335x-based 'Gumstix Pepper' SBCs and variants use different types of
RAM (DDR2 vs DDR3 with DDR3 being the default). Detect the board type
by reading the factory-programmed EEPROM [1] and use this to select any
runtime boot options such as RAM type.
[1] http://elinux.org/BeagleBoardPinMux#List_of_Vendor_and_Device_IDs
Signed-off-by: Adam YH Lee <[email protected]>
Signed-off-by: Ash Charles <[email protected]>
|
|
This patch moves the following config options to Kconfig:
CONFIG_AUTOBOOT_KEYED
CONFIG_AUTOBOOT_PROMPT
CONFIG_AUTOBOOT_DELAY_STR
CONFIG_AUTOBOOT_STOP_STR
AUTOBOOT_KEYED_CTRLC
Signed-off-by: Stefan Roese <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
[trini: Drop ip04 and pm9263 configs/ additions, those boards previously
set CONFIG_AUTOBOOT_PROMPT but never used it, re-run savedefconfig over
all boards that did change. Make digsy_mtc_* string include seconds to
match others and not warn. ]
Signed-off-by: Tom Rini <[email protected]>
Cc: Masahiro Yamada <[email protected]>
|
|
This patch enables all functions required to use DFU/THOR and UMS:
- DWC3: core, gadget, Samsung DWC3 PHY
- USB gadget: endpoint autoconf, downloader, DFU, THOR, UMS
The CONFIG_EXTRA_ENV_SETINGS from exynos5-common.h is redefined
and appended by dfu environment setting and some system settings.
The boot is still using $distro_boot as previous.
Signed-off-by: Inha Song <[email protected]>
Signed-off-by: Lukasz Majewski <[email protected]>
Signed-off-by: Joonyoung Shim <[email protected]>
Signed-off-by: Przemyslaw Marczak <[email protected]>
Cc: Minkyu Kang <[email protected]>
|
|
|
|
Signed-off-by: Bhuvanchandra DV <[email protected]>
Acked-by: Stefan Agner <[email protected]>
|
|
Acked-by: Stefan Agner <[email protected]>
Signed-off-by: Bhuvanchandra DV <[email protected]>
|
|
Commit 8183058188cd2d942 ("imx6: centralise common boot options in
mx6_common.h") broke boot on mx6sl and mx6sx by assuming that all mx6
SoCs use the same LOADADDR/SYS_TEXT_BASE range, which is not correct.
DDR on mx6sx/mx6sl starts at 0x80000000.
Adjust LOADADDR/SYS_TEXT_BASE to the proper values for mx6sx/mx6sl,
so that these SoCs can boot again.
Also, TQMA6 requires a custom CONFIG_SYS_TEXT_BASE value, so move
its setting prior to the inclusion of mx6_common.h.
Signed-off-by: Fabio Estevam <fabio.estevam at freescale.com>
|
|
There are two revisions of wandboard: version B1 and C1.
Add the revision detection support, so that the correct dtb file can
be automatically loaded.
Based on the patch from Richard Hu <[email protected]>.
Signed-off-by: Fabio Estevam <[email protected]>
Reviewed-by: Stefano Babic <[email protected]>
Tested-By: Vagrant Cascadian <[email protected]>
|
|
Signed-off-by: Gabriel Huau <[email protected]>
Acked-by: Simon Glass <[email protected]>
|
|
Support QEMU PIRQ routing via device tree on both i440fx and q35
platforms. With this commit, Linux booting on QEMU from U-Boot
has working ATA/SATA, USB and ethernet.
Signed-off-by: Bin Meng <[email protected]>
Acked-by: Simon Glass <[email protected]>
|
|
The default weak version of pci_skip_dev() in drivers/pci/pci_common.c
skips the host bridge (b.d.f = 0.0.0) which is actually the i440fx/q35
chipset for QEMU targets. Define CONFIG_PCI_CONFIG_HOST_BRIDGE to make
it visible in the PCI configuration space.
Signed-off-by: Bin Meng <[email protected]>
Acked-by: Simon Glass <[email protected]>
|
|
Intel Quark SoC has the same interrupt routing mechanism as the
Queensbay platform, only the difference is that PCI devices'
INTA/B/C/D are harcoded and cannot be changed freely.
Signed-off-by: Bin Meng <[email protected]>
Acked-by: Simon Glass <[email protected]>
|
|
Enable legacy IDE support on the pc target and AHCI support on the
q35 target. Default configuration is to support the pc target.
Signed-off-by: Bin Meng <[email protected]>
Acked-by: Simon Glass <[email protected]>
|
|
Enable CONFIG_LBA48 to support large disks. CONFIG_ATAPI is only needed
by cmd_ide.c which is not common for modern x86 targets, hence remove it.
Signed-off-by: Bin Meng <[email protected]>
Acked-by: Simon Glass <[email protected]>
|
|
It turns out that QEMU x86 emulated graphic card has a built-in
option ROM which can be run perfectly with native mode by U-Boot.
Signed-off-by: Bin Meng <[email protected]>
Acked-by: Simon Glass <[email protected]>
|
|
CONFIG_FRAMEBUFFER_SET_VESA_MODE and CONFIG_FRAMEBUFFER_VESA_MODE
are not x86-specific, so move them to drivers/video/Kconfig and
make them depend on VIDEO_VESA driver. Some cosmetic fixes are
applied to the Kconfig help text as well.
Signed-off-by: Bin Meng <[email protected]>
Acked-by: Simon Glass <[email protected]>
|
|
Some x86 boards set CONFIG_NR_DRAM_BANKS to 1, which causes incorrect
DRAM size printed when booting from coreboot, like this:
CPU: x86, vendor Intel, device 663h
DRAM: 636 KiB
Using default environment
Change it to 8 which should be enough for both coreboot and bare
cases, and move it to x86-common.h.
Signed-off-by: Bin Meng <[email protected]>
Acked-by: Simon Glass <[email protected]>
|
|
This commit introduces the initial U-Boot support for QEMU x86 targets.
U-Boot can boot from coreboot as a payload, or directly without coreboot.
Signed-off-by: Bin Meng <[email protected]>
Acked-by: Simon Glass <[email protected]>
Tested-by: Simon Glass <[email protected]>
Merged in patch 'x86: qemu: Add CMD_NET to qemu-x86_defconfig
https://patchwork.ozlabs.org/patch/479745/
|
|
netconsole had become defective over time and cleanups.
Because the feature is used very rarely nobody did take notice about this
defect.
With this patch the resulting syntax error on call will be fixed.
Signed-off-by: Hannes Schmelzer <[email protected]>
|
|
CONFIG_NET_MULTI is not used anywhere and thus can safely be removed
from the configs.
Acked-by: Marek Vasut <[email protected]>
Acked-by: Viresh Kumar <[email protected]>
Signed-off-by: Lars Poeschel <[email protected]>
|
|
The config for pcm051 still undef'd CONFIG_USE_IRQ. This is not
needed any more since it is not defined in the whole include path
before.
Signed-off-by: Lars Poeschel <[email protected]>
|
|
Fixup include/configs/unipher.h to not set CONFIG_LIB_RAND
Signed-off-by: Tom Rini <[email protected]>
|
|
NET_RANDOM_ETHADDR depends on lib/rand.c. This patch adds dependency to
Kconfig to ensure that library is also compiled.
Remove the definitions from Blackfin boards' include/configs.
Signed-off-by: Michal Simek <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
This also selects CONFIG_NET for any CONFIG_CMD_NET board.
Remove the imx default for CONFIG_NET.
This moves the config that was defined by 60296a8 (commands: add more
command entries in Kconfig).
Signed-off-by: Joe Hershberger <[email protected]>
|
|
Another shell scripting command that has not been moved.
Moved using tools/moveconfig.py using these settings:
CMD_SETEXPR bool n y
Signed-off-by: Joe Hershberger <[email protected]>
Cc: Masahiro Yamada <[email protected]>
|
|
Commit 92ac52082140 (net: Remove all references to CONFIG_ETHADDR
and friends) accidentally dropped #endif. Since then, gr_ep2s60
could not build.
scripts/kconfig/conf --silentoldconfig Kconfig
CHK include/config.h
GEN include/autoconf.mk
In file included from include/config.h:5:0,
from ./include/common.h:18:
include/configs/gr_ep2s60.h:15:0: error: unterminated #ifndef
#ifndef __CONFIG_H__
^
make[1]: *** [include/autoconf.mk] Error 1
Signed-off-by: Masahiro Yamada <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
