| Age | Commit message (Collapse) | Author |
|---|
|
SerDes driver is used by other sub systems like PCI, sRIO etc.
So modify it to be more general. The SerDes driver provides common
API's that can also be extended for other peripherals SerDes
configurations.
Signed-off-by: Hao Zhang <[email protected]>
Signed-off-by: Ivan Khoronzhuk <[email protected]>
|
|
Enhance the driver to use cmu/comlane/lane specific configurations
instead of 1 big array of configuration.
Signed-off-by: Hao Zhang <[email protected]>
Signed-off-by: Ivan Khoronzhuk <[email protected]>
|
|
This patch split the Keystone II SGMII SerDes related code from
Ethernet driver and create a separate SGMII SerDes driver.
The SerDes driver can be used by others keystone subsystems
like PCI, sRIO, so move it to driver/soc/keystone directory.
Add soc specific drivers directory like in the Linux kernel.
It is going to be used by keysotone soc specific drivers.
Signed-off-by: Hao Zhang <[email protected]>
Signed-off-by: Ivan Khoronzhuk <[email protected]>
|
|
The header file for the driver should be in correct place.
So move it to "arch/arm/include/asm/ti-common/keystone_net.h"
and correct driver's external dependencies. At the same time
align and correct some definitions.
Acked-by: Murali Karicheri <[email protected]>
Signed-off-by: Ivan Khoronzhuk <[email protected]>
|
|
Currently the network driver is used only by k2hk evm board.
The k2hk SoC contains NETCP v1.0, but Keystone2 SoCs, like k2e
contain NETCP v1.5. So driver should be able to work with such kind
of NETCP. This commit adds this opportunity. The main difference in
masks and some registers, the logic is the same, so only definitions
should be changed. To differentiate between versions add KS2_NETCP_V1_0
and KS2_NETCP_V1_5. Also remove unused and no more needed defines.
The port number is specific for each board so move this parameter to
configuration.
Acked-by: Murali Karicheri <[email protected]>
Signed-off-by: Hao Zhang <[email protected]>
Signed-off-by: Ivan Khoronzhuk <[email protected]>
|
|
Currently keystone has misc_init_r where all DSPS are turned off
by default. So enable this function.
Signed-off-by: Ivan Khoronzhuk <[email protected]>
|
|
This patch adds Keystone II Lammar (K2L) EVM board support.
Acked-by: Vitaly Andrianov <[email protected]>
Signed-off-by: Hao Zhang <[email protected]>
Signed-off-by: Ivan Khoronzhuk <[email protected]>
|
|
Add support of usb xhci. xHCI controls all USB speeds of the Host
mode, that is, the SS through the SS PHY, as well as the HS, FS, and
LS through the USB2 PHY. xHCI replaces and supersedes all previous
host HCIs (HS-only EHCI, FS/LS OHCI and UHCI), and is therefore not
backwards compatible with any of them. The USB3SS’s USB Controller is
fully compliant with xHC.
Acked-by: Vitaly Andrianov <[email protected]>
Signed-off-by: WingMan Kwok <[email protected]>
Signed-off-by: Ivan Khoronzhuk <[email protected]>
|
|
The keystone_nav driver is general driver intended to be used for
working with queue manager and pktdma for different IPs like NETCP,
AIF, FFTC, etc. So the it's API shouldn't be named like it works only
with one of them, it should be general names. The names with prefix
like netcp_* rather do for drivers/net/keystone_net.c driver. So it's
good to generalize this driver to be used for different IP's and
delete confusion with real NETCP driver.
The current netcp_* functions of keystone navigator can be used for
other settings of pktdma, not only for NETCP. The API of this driver
is used by the keystone_net driver to work with NETCP, so net driver
also should be corrected. For convenience collect pkdma
configurations in drivers/dma/keystone_nav_cfg.c.
Acked-by: Vitaly Andrianov <[email protected]>
Signed-off-by: Ivan Khoronzhuk <[email protected]>
|
|
The keystone_nav is used by drivers/net/keystone_net.c driver to
send and receive packets, but currently it's placed at keystone
arch sources. So it should be in the drivers directory also.
It's separate driver that can be used for sending and receiving
pktdma packets by others drivers also.
This patch just move this driver to appropriate directory and
doesn't add any functional changes.
Acked-by: Murali Karicheri <[email protected]>
Signed-off-by: Ivan Khoronzhuk <[email protected]>
|
|
The maxBCM board is equipped with the Marvell Armada-XP MV78460 SoC. It
integrates an SPI NOR flash and an Marvell 88E6185 switch.
Signed-off-by: Stefan Roese <[email protected]>
|
|
This patch adds basic support for the Marvell DB-MV784MP-GP evaulation
board. This is the first board that uses the recently created
Armada XP 78460 SoC support.
Signed-off-by: Stefan Roese <[email protected]>
Tested-by: Luka Perkov <[email protected]>
|
|
|
|
Commit 155fa9af95ac5be857a7327e7a968a296e60d4c8 changed the way
to define a GPIO line, which can be used to force CS high
across multiple transactions. In order to fix sf detection
change board code to make use of board_spi_cs_gpio(..).
Signed-off-by: Christian Gmeiner <[email protected]>
Acked-by: Stefano Babic <[email protected]>
Acked-by: Nikita Kiryanov <[email protected]>
|
|
Enable FIT support and the bootelf command. Also change the default load
address to somewhere other than the normal load address of the kernel,
to allow for decompression without overwriting the original file.
Signed-off-by: Simon Glass <[email protected]>
|
|
To get a display in U-Boot on link you must either build a coreboot that
always sets it up, or use Esc-Refresh-Power to reset the machine.
When we do have a display, it is nice to display the model at the top, so
enable this option.
Signed-off-by: Simon Glass <[email protected]>
|
|
We may as well use hush. The auto-complete option was incorrect so this was
not enabled. Also expand the command line size a little and go back to the
default prompt since "boot>" doesn't seem any more useful.
Signed-off-by: Simon Glass <[email protected]>
|
|
Add defines to enable the Chrome OS EC interface and set it up on init.
Signed-off-by: Simon Glass <[email protected]>
|
|
The dhcp option is required to get bootp to work on the Chromebook Pixel,
so enable it.
Signed-off-by: Simon Glass <[email protected]>
|
|
USB support must be enabled before config_distro_bootcmd.h is included
for bootcmd to include USB-related functionality.
Signed-off-by: Stephen Warren <[email protected]>
|
|
The built-in SMSC 95xx chip doesn't know its own MAC address. Instead,
we must query it from the VC firmware; it's probably encoded in fuses
on the BCM2835.
Signed-off-by: Stephen Warren <[email protected]>
|
|
Enable DWC2 USB, storage and ethernet support. Tested on RPi B+.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Stephen Warren <[email protected]>
Cc: Chin Liang See <[email protected]>
Cc: Dinh Nguyen <[email protected]>
Cc: Albert Aribaud <[email protected]>
Cc: Tom Rini <[email protected]>
Cc: Wolfgang Denk <[email protected]>
Cc: Pavel Machek <[email protected]>
|
|
Convert the BCM2835 GPIO driver to use driver model, and switch over
Raspberry Pi to use this, since it is the only board.
Signed-off-by: Simon Glass <[email protected]>
Tested-by: Stephen Warren <[email protected]>
Acked-by: Stephen Warren <[email protected]>
|
|
Now that serial and GPIO are available for iMX.6, move cm_fx6 over as an
example.
Acked-by: Igor Grinberg <[email protected]>
Signed-off-by: Simon Glass <[email protected]>
Acked-by: Nikita Kiryanov <[email protected]>
|
|
Adjust this driver to use driver model and move smdk5420 boards over to
use it.
Acked-by: Jagannadha Sutradharudu Teki <[email protected]>
Signed-off-by: Simon Glass <[email protected]>
|
|
Adjust the sandbox cros_ec emulation driver to work with driver model, and
switch over to driver model for sandbox cros_ec.
Signed-off-by: Simon Glass <[email protected]>
Acked-by: Jagannadha Sutradharudu Teki <[email protected]>
|
|
This converts the Tegra SPI drivers to use driver model. This is tested
on:
- Tegra20 - trimslice
- Tegra30 - beaver
- Tegra124 - dalmore
(not tested on Tegra124)
Reviewed-by: Jagannadha Sutradharudu Teki <[email protected]>
Signed-off-by: Simon Glass <[email protected]>
|
|
Use driver model for exynos5 board SPI flash.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Jagannadha Sutradharudu Teki <[email protected]>
|
|
Convert sandbox's spi flash emulation driver to use driver model.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Jagannadha Sutradharudu Teki <[email protected]>
|
|
Adjust this board to use the driver model soft_spi implementation.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Jagannadha Sutradharudu Teki <[email protected]>
|
|
Move the exynos SPI driver over to driver model. This removes quite a bit
of boilerplate from the driver, although it adds some for driver model.
A few device tree additions are needed to make the SPI flash available.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Jagannadha Sutradharudu Teki <[email protected]>
|
|
This feature provides for init of a single SPI port for the soft SPI
feature. It is not really compatible with driver model since it assumes a
single SPI port. Also, inserting SPI init into the driver by means of
a #define is not very nice.
This feature is not used by any active boards, so let's remove it.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Jagannadha Sutradharudu Teki <[email protected]>
|
|
Adjust the sandbox SPI driver to support driver model and move sandbox over
to driver model for SPI.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Jagannadha Sutradharudu Teki <[email protected]>
|
|
Change the Exynos serial driver to work with driver model and switch over
all relevant boards to use it.
Signed-off-by: Simon Glass <[email protected]>
|
|
Convert the exynos GPIO driver to driver model. This implements the generic
GPIO interface but not the extra Exynos-specific functions.
Signed-off-by: Simon Glass <[email protected]>
|
|
The generic board deadline is approaching, and we need this feature to
enable driver model. Enable CONFIG_SYS_GENERIC_BOARD for s5p_goni.
Signed-off-by: Simon Glass <[email protected]>
|
|
The generic board deadline is approaching, and we need this feature to
enable driver model. Enable CONFIG_SYS_GENERIC_BOARD for smdkc100.
Signed-off-by: Simon Glass <[email protected]>
|
|
Add proper initialization of GPIO pins used by software i2c.
Signed-off-by: Robert Baldyga <[email protected]>
Acked-by: Simon Glass <[email protected]>
|
|
Update Apalis T30 as per the following commits
c369139234c03b1494394d12cd27009f47aa6606
tegra: dts: Add serial port details
461be2f96e4b87e5065208c6659a47dd0ad9e9f8
kconfig: remove redundant "string" type in arch and board Kconfigs
f1ef2b62339526df3b921bcfefd174ce76d4c624
kconfig: move CONFIG_DEFAULT_DEVICE_TREE to kconfig
Signed-off-by: Marcel Ziswiler <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
Clean-up a spurious new line which got introduced resp. left behind by
commit
f1ef2b62339526df3b921bcfefd174ce76d4c624
kconfig: move CONFIG_DEFAULT_DEVICE_TREE to kconfig
Signed-off-by: Marcel Ziswiler <[email protected]>
Acked-by: Simon Glass <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
Wondering what exactly that one should bring (;-p). Looks like a remnant of the last commit
783e6a72b8278d59854ced41a4696c9a14abbb0b
kconfig: move CONFIG_OF_* to Kconfig
Signed-off-by: Marcel Ziswiler <[email protected]>
Acked-by: Simon Glass <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
Use architecture specific memcpy to speed up things.
Signed-off-by: Marcel Ziswiler <[email protected]>
Tested-by: Stephen Warren <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
This patch adds board support for the Toradex Apalis T30 a computer on
module which can be used on different carrier boards.
For the sake of ease of use we do not distinguish between different
carrier boards for now as the base module features are deemed
sufficient enough for regular booting.
The following functionality is working so far:
- eMMC boot and environment storage
- Gigabit Ethernet (once Thierry's PCIe as well as my E1000 resp. i210
fixes hit mainline)
- MMC/SD cards (both 8-bit as well as 4-bit slot)
- USB client/host (dual role port as client e.g. for DFU/UMS, other two
ports as host)
Signed-off-by: Marcel Ziswiler <[email protected]>
Acked-by: Stephen Warren <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
HDMI config options can be placed into the common mx6sabre_common.h file to
avoid duplication.
Signed-off-by: Fabio Estevam <[email protected]>
|
|
Let HDMI splash screen support work by default.
Signed-off-by: Fabio Estevam <[email protected]>
|
|
|
|
Signed-off-by: Ruchika Gupta <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
Enable blob commands for platforms having SEC 4.0 or greater
for secure boot scenarios
Signed-off-by: Ruchika Gupta <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
Hardware accelerated support for SHA-1 and SHA-256 has been added.
Hash command enabled along with hardware accelerated support for
SHA-1 and SHA-256 for platforms which have CAAM block.
Signed-off-by: Ruchika Gupta <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
Enable CAAM in platforms supporting the hardware block.
Hash command enabled along with hardware accelerated support for
SHA-1 and SHA-256 for platforms which have CAAM block.
Signed-off-by: Ruchika Gupta <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
