| Age | Commit message (Collapse) | Author |
|---|
|
This patch adds support of rcw for T1042RDB, it makes following changes :
- Adds t1042_rcw.cfg file for serdes protocol 0x86 for T1042RDB
- Renames t1042_pi_rcw.cfg file from t1042_rcw.cfg and also updates
comments for valid serdes protocol which is 0x06
- Also updates CONFIG_SYS_FSL_PBL_RCW for T1042RDB
Signed-off-by: Vijay Rai <[email protected]>
Signed-off-by: Priyanka Jain <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
Enable the Extend address to support SPI flash more than 16MB.
Signed-off-by: Hou Zhiqiang <[email protected]>
Reviewed-by: Jagannadha Sutradharudu Teki <[email protected]>
|
|
Currently, CONFIG_SPL_SPI_* #defines are used for controlling SPI boot in
SPL. These #defines do not allow the user to select SPI mode for the SPI flash
(there's no CONFIG_SPL_SPI_MODE, so the SPI mode is hardcoded in
spi_spl_load.c), and duplicate information already provided by
CONFIG_SF_DEFAULT_* #defines.
Kill CONFIG_SPL_SPI_*, and use CONFIG_SF_DEFAULT_* instead.
Cc: Tom Rini <[email protected]>
Cc: Marek Vasut <[email protected]>
Cc: Sudhakar Rajashekhara <[email protected]>
Cc: Lokesh Vutla <[email protected]>
Cc: Vitaly Andrianov <[email protected]>
Cc: Lars Poeschel <[email protected]>
Cc: Bo Shen <[email protected]>
Cc: Hannes Petermaier <[email protected]>
Cc: Michal Simek <[email protected]>
Acked-by: Marek Vasut <[email protected]>
Signed-off-by: Nikita Kiryanov <[email protected]>
Reviewed-by: Jagannadha Sutradharudu Teki <[email protected]>
|
|
MXC SPI driver has a feature whereas a GPIO line can be used to force CS high
across multiple transactions. This is set up by embedding the GPIO information
in the CS value:
cs = (cs | gpio << 8)
This merge of cs and gpio data into one value breaks the sf probe command:
if the use of gpio is required, invoking "sf probe <cs>" will not work, because
the CS argument doesn't have the GPIO information in it. Instead, the user must
use "sf probe <cs | gpio << 8>". For example, if bank 2 gpio 30 is used to force
cs high on cs 0, bus 0, then instead of typing "sf probe 0" the user now must
type "sf probe 15872".
This is inconsistent with the description of the sf probe command, and forces
the user to be aware of implementaiton details.
Fix this by introducing a new board function: board_spi_cs_gpio(), which will
accept a naked CS value, and provide the driver with the relevant GPIO, if one
is necessary.
Cc: Eric Nelson <[email protected]>
Cc: Eric Benard <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Tim Harvey <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Tom Rini <[email protected]>
Cc: Marek Vasut <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
Signed-off-by: Nikita Kiryanov <[email protected]>
Reviewed-by: Jagannadha Sutradharudu Teki <[email protected]>
|
|
Let's enable CONFIG_SYS_GENERIC_BOARD in order to get rid of warnings related
to generic board support is not in place.
Signed-off-by: Fabio Estevam <[email protected]>
|
|
We should pass the MMC1 base address into CONFIG_SYS_FSL_ESDHC_ADDR.
Signed-off-by: Fabio Estevam <[email protected]>
|
|
on Sabrelite board
Sabrelite board has two solts: 0 is SD3 (bottom) slot and 1 is uSD4 (top) slot.
This patch makes use of both slots instead of only one.
Signed-off-by: Guillaume GARDET <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Eric Nelson <[email protected]>
Reviewed-by: Eric Nelson <[email protected]>
Acked-by: Eric Nelson <[email protected]>
Reviewed-by: Eric Nelson <[email protected]>
Acked-by: Eric Nelson <[email protected]>
|
|
|
|
Let's enable CONFIG_SYS_GENERIC_BOARD in order to get rid of warnings related
to generic board not being supported.
Signed-off-by: Fabio Estevam <[email protected]>
|
|
We should pass the SDHC1 base address into CONFIG_SYS_FSL_ESDHC_ADDR.
Signed-off-by: Fabio Estevam <[email protected]>
|
|
We should not hardcode CONFIG_NETMASK in the config file.
Signed-off-by: Fabio Estevam <[email protected]>
Acked-by: Igor Grinberg <[email protected]>
Acked-by: Nikita Kiryanov <[email protected]>
|
|
|
|
Signed-off-by: Josh Wu <[email protected]>
Signed-off-by: Andreas Bießmann <[email protected]>
|
|
Signed-off-by: Josh Wu <[email protected]>
Signed-off-by: Andreas Bießmann <[email protected]>
|
|
Signed-off-by: Bo Shen <[email protected]>
Signed-off-by: Andreas Bießmann <[email protected]>
|
|
This patch adds boot script support to am335x_evm
Signed-off-by: Guillaume GARDET <[email protected]>
Cc: Tom Rini <[email protected]>
|
|
and 'loadbootenv' as already done for 'loadimage' and 'loaduimage'.
This patch uses generic 'load' command instead of 'fatload' for 'loadbootscript' and 'loadbootenv' as already done for 'loadimage' and 'loaduimage' for OMAP4 boards.
This allows to use EXT partition instead of FAT, while keeping FAT compatibility.
Signed-off-by: Guillaume GARDET <[email protected]>
Cc: Tom Rini <[email protected]>
|
|
|
|
Define CONFIG_SYS_FSL_ESDHC_ADDR using USDHC2_BASE_ADDR which is
used in board_mmc_init.
Signed-off-by: Peng Fan <[email protected]>
|
|
Define CONFIG_SYS_FSL_ESDHC_ADDR using USDHC4_BASE_ADDR.
USDHC3 and USDHC4 are both initialized in board_mmc_init. There is
no restriction on USDHC3 addr or USDHC4 addr should be assigned to
CONFIG_SYS_FSL_ESDHC_ADDR. So, just choose USDHC4_BASE_ADDR to avoid
errors when fsl_esdhc_mmc_init is invoked.
Signed-off-by: Peng Fan <[email protected]>
|
|
Define CONFIG_SYS_FSL_ESDHC_ADDR using USDHC4_BASE_ADDR which is used
in board_mmc_init.
If board_mmc_init failed, cpu_mmc_init->fsl_esdhc_mmc_init will use
CONFIG_SYS_FSL_ESDHC_ADDR to initialize sdhc. So set this macro to
correct value.
Signed-off-by: Peng Fan <[email protected]>
|
|
This adds NAND support for the Vybrid tower system (TWR-VF65GS10)
provided by the vf610_nfc driver. Full 16-Bit bus width is
supported. Also an aditional config vf610twr_nand is introduced
which gets the environment from NAND. However, booting U-Boot from
NAND is not yet possible due to missing boot configuration block
(BCB).
Signed-off-by: Stefan Agner <[email protected]>
|
|
|
|
|
|
Enable CONFIG_SYS_GENERIC_BOARD for imx6slevk to use generic board.
Signed-off-by: Ye.Li <[email protected]>
|
|
Enable the CONFIG_SYS_GENERIC_BOARD for imx6q/dl arm2 board to
use generic board.
Signed-off-by: Ye.Li <[email protected]>
|
|
Use driver model for serial ports.
Since Tegra now uses driver model for serial, adjust the definition of
V_NS16550_CLK so that it is clear that this is only used for SPL.
Signed-off-by: Simon Glass <[email protected]>
|
|
Adjust the sandbox serial driver to use the new driver model uclass. The
driver works much as before, but within the new framework.
Signed-off-by: Simon Glass <[email protected]>
|
|
This is an implementation of GPIOs for Tegra that uses driver model. It has
been tested on trimslice and also using the new iotrace feature.
The implementation uses a top-level GPIO device (which has no actual GPIOS).
Under this all the banks are created as separate GPIO devices.
The GPIOs are named as per the Tegra datasheet/header files: A0..A7, B0..B7,
..., Z0..Z7, AA0..AA7, etc.
Since driver model is not yet available before relocation, or in SPL, a
special function is provided for seaboard's SPL code.
Signed-off-by: Simon Glass <[email protected]>
|
|
Allocate 1KB so that driver model can operate before relocation.
Signed-off-by: Simon Glass <[email protected]>
|
|
Tested with an Intel Wireless PCI 7260HMW card:
U-Boot 2014.10-rc1-16576-g4a8a8a8-dirty (Aug 23 2014 - 16:05:11)
CPU: Freescale i.MX6SX rev1.0 at 792 MHz
Reset cause: WDOG
Board: MX6SX SABRE SDB
I2C: ready
DRAM: 1 GiB
MMC: FSL_SDHC: 0
00:01.0 - 16c3:abcd - Bridge device
01:00.0 - 8086:08b1 - Network controller
Signed-off-by: Fabio Estevam <[email protected]>
|
|
Commit fa9c021632473 ("mx6: add example DTB for mx6qsabreauto") introduced
'imx6q-sabreauto.dts' but it adds no real value as the dts file only contains
the 'model' and 'compatible' strings.
After this commit the final binary is also changed from 'u-boot.imx' to
'u-boot-dtb.imx', which may confuse users.
So revert it until a more complete and useful device tree could be provided.
Signed-off-by: Fabio Estevam <[email protected]>
Acked-by: Otavio Salvador <[email protected]>
|
|
filesystem independent
nitrogen6x.h file defines CONFIG_CMD_FS_GENERIC, so we are able to use generic
'load' command instead of 'fatload'. It allows to use ext filesystem and keep
compatibilty with fat filesystem.
Signed-off-by: Guillaume GARDET <[email protected]>
Cc: Stefano Babic <[email protected]>
Acked-By: Eric Nelson <[email protected]>
|
|
Most Gateworks Ventana boards use a PLX PEX860x PCIe switch for PCIe expansion.
These boards use GPIO on the PLX device as PERST# for the downstream ports
thus we assert this when the PLX is enumerated.
Signed-off-by: Tim Harvey <[email protected]>
|
|
Add support for SATA.
Cc: Igor Grinberg <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Tom Rini <[email protected]>
Signed-off-by: Nikita Kiryanov <[email protected]>
|
|
Use Compulab eeprom module to obtain revision number, serial number, and
mac address from the EEPROM.
Cc: Igor Grinberg <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Tom Rini <[email protected]>
Signed-off-by: Nikita Kiryanov <[email protected]>
|
|
Add support for all 3 I2C busses on Compulab CM-FX6 CoM.
Cc: Igor Grinberg <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Tom Rini <[email protected]>
Acked-by: Igor Grinberg <[email protected]>
Signed-off-by: Nikita Kiryanov <[email protected]>
|
|
Add USB and USB OTG host support for Compulab CM-FX6 CoM.
Cc: Igor Grinberg <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Tom Rini <[email protected]>
Signed-off-by: Nikita Kiryanov <[email protected]>
|
|
Add ethernet support for Compulab CM-FX6 CoM
Cc: Igor Grinberg <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Tom Rini <[email protected]>
Acked-by: Igor Grinberg <[email protected]>
Signed-off-by: Nikita Kiryanov <[email protected]>
|
|
Add NAND support for Compulab CM-FX6 CoM.
Cc: Igor Grinberg <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Tom Rini <[email protected]>
Acked-by: Igor Grinberg <[email protected]>
Signed-off-by: Nikita Kiryanov <[email protected]>
|
|
Add initial support for Compulab CM-FX6 CoM.
Support includes MMC, SPI flash, and SPL with dynamic DRAM detection.
Cc: Igor Grinberg <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Tom Rini <[email protected]>
Cc: Marek Vasut <[email protected]>
Cc: Simon Glass <[email protected]>
Acked-by: Marek Vasut <[email protected]>
Signed-off-by: Nikita Kiryanov <[email protected]>
|
|
Create CONFIG_SYS_I2C_EEPROM_BUS #define to tell the EEPROM
module what I2C bus the EEPROM is located at. Make cl_eeprom_read()
switch to that bus when reading EEPROM.
Cc: Igor Grinberg <[email protected]>
Cc: Dmitry Lifshitz <[email protected]>
Cc: Tom Rini <[email protected]>
Cc: Marek Vasut <[email protected]>
Acked-by: Igor Grinberg <[email protected]>
Acked-by: Dmitry Lifshitz <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
Signed-off-by: Nikita Kiryanov <[email protected]>
|
|
|
|
|
|
This patch adds the TWR_LCD_RGB card/HDMI options and the common
configuration for DCU on LS1021ATWR board.
Signed-off-by: Alison Wang <[email protected]>
|
|
LS102xA is an ARMv7 implementation. This patch is to add
basic support for LS1021ATWR board.
One DDR controller
DUART1 is used as the console
For the detail board information, please refer to README.
Signed-off-by: Chen Lu <[email protected]>
Signed-off-by: Yuan Yao <[email protected]>
Signed-off-by: Alison Wang <[email protected]>
|
|
LS102xA is an ARMv7 implementation. This patch is to add
basic support for LS1021AQDS board.
One DDR controller
DUART1 is used as the console
For the detail board information, please refer to README.
Signed-off-by: Alison Wang <[email protected]>
Signed-off-by: Jason Jin <[email protected]>
Signed-off-by: York Sun <[email protected]>
Signed-off-by: Yuan Yao <[email protected]>
Signed-off-by: Prabhakar Kushwaha <[email protected]>
|
|
Enable drivers for FIMD, DP and parade bridge chip.
Signed-off-by: Ajay Kumar <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
Previously, we used to statically assign values for vl_col, vl_row and
vl_bpix using #defines like LCD_XRES, LCD_YRES and LCD_COLOR16.
Introducing the function exynos_lcd_early_init() would take care of this
assignment on the fly by parsing FIMD DT properties, thereby allowing us
to remove LCD_XRES and LCD_YRES from the main config file.
Signed-off-by: Ajay Kumar <[email protected]>
Acked-by: Simon Glass <[email protected]>
Tested-by: Simon Glass <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
Patch is the result of:
sed -i -e 's/FTDFILE/FDTFILE/g' board/sunxi/Kconfig configs/* include/configs/sunxi-common.h
sed -i -e 's/ftdfile/fdtfile/g' board/sunxi/Kconfig
Reported-by: Vagrant Cascadian <[email protected]>
Signed-off-by: Ian Campbell <[email protected]>
Acked-by: Hans de Goede <[email protected]>
[ ijc -- s/Spotted-by/Reported-by/ and resolve conflict vs "remove
redundant "SPL" from CONFIG_SYS_EXTRA_OPTIONS" ]
|
