| Age | Commit message (Collapse) | Author |
|---|
|
Most Gateworks Ventana boards use a PLX PEX860x PCIe switch for PCIe expansion.
These boards use GPIO on the PLX device as PERST# for the downstream ports
thus we assert this when the PLX is enumerated.
Signed-off-by: Tim Harvey <[email protected]>
|
|
Add support for SATA.
Cc: Igor Grinberg <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Tom Rini <[email protected]>
Signed-off-by: Nikita Kiryanov <[email protected]>
|
|
Use Compulab eeprom module to obtain revision number, serial number, and
mac address from the EEPROM.
Cc: Igor Grinberg <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Tom Rini <[email protected]>
Signed-off-by: Nikita Kiryanov <[email protected]>
|
|
Add support for all 3 I2C busses on Compulab CM-FX6 CoM.
Cc: Igor Grinberg <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Tom Rini <[email protected]>
Acked-by: Igor Grinberg <[email protected]>
Signed-off-by: Nikita Kiryanov <[email protected]>
|
|
Add USB and USB OTG host support for Compulab CM-FX6 CoM.
Cc: Igor Grinberg <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Tom Rini <[email protected]>
Signed-off-by: Nikita Kiryanov <[email protected]>
|
|
Add ethernet support for Compulab CM-FX6 CoM
Cc: Igor Grinberg <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Tom Rini <[email protected]>
Acked-by: Igor Grinberg <[email protected]>
Signed-off-by: Nikita Kiryanov <[email protected]>
|
|
Add NAND support for Compulab CM-FX6 CoM.
Cc: Igor Grinberg <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Tom Rini <[email protected]>
Acked-by: Igor Grinberg <[email protected]>
Signed-off-by: Nikita Kiryanov <[email protected]>
|
|
Add initial support for Compulab CM-FX6 CoM.
Support includes MMC, SPI flash, and SPL with dynamic DRAM detection.
Cc: Igor Grinberg <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Tom Rini <[email protected]>
Cc: Marek Vasut <[email protected]>
Cc: Simon Glass <[email protected]>
Acked-by: Marek Vasut <[email protected]>
Signed-off-by: Nikita Kiryanov <[email protected]>
|
|
Create CONFIG_SYS_I2C_EEPROM_BUS #define to tell the EEPROM
module what I2C bus the EEPROM is located at. Make cl_eeprom_read()
switch to that bus when reading EEPROM.
Cc: Igor Grinberg <[email protected]>
Cc: Dmitry Lifshitz <[email protected]>
Cc: Tom Rini <[email protected]>
Cc: Marek Vasut <[email protected]>
Acked-by: Igor Grinberg <[email protected]>
Acked-by: Dmitry Lifshitz <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
Signed-off-by: Nikita Kiryanov <[email protected]>
|
|
|
|
|
|
This patch adds the TWR_LCD_RGB card/HDMI options and the common
configuration for DCU on LS1021ATWR board.
Signed-off-by: Alison Wang <[email protected]>
|
|
LS102xA is an ARMv7 implementation. This patch is to add
basic support for LS1021ATWR board.
One DDR controller
DUART1 is used as the console
For the detail board information, please refer to README.
Signed-off-by: Chen Lu <[email protected]>
Signed-off-by: Yuan Yao <[email protected]>
Signed-off-by: Alison Wang <[email protected]>
|
|
LS102xA is an ARMv7 implementation. This patch is to add
basic support for LS1021AQDS board.
One DDR controller
DUART1 is used as the console
For the detail board information, please refer to README.
Signed-off-by: Alison Wang <[email protected]>
Signed-off-by: Jason Jin <[email protected]>
Signed-off-by: York Sun <[email protected]>
Signed-off-by: Yuan Yao <[email protected]>
Signed-off-by: Prabhakar Kushwaha <[email protected]>
|
|
Enable drivers for FIMD, DP and parade bridge chip.
Signed-off-by: Ajay Kumar <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
Previously, we used to statically assign values for vl_col, vl_row and
vl_bpix using #defines like LCD_XRES, LCD_YRES and LCD_COLOR16.
Introducing the function exynos_lcd_early_init() would take care of this
assignment on the fly by parsing FIMD DT properties, thereby allowing us
to remove LCD_XRES and LCD_YRES from the main config file.
Signed-off-by: Ajay Kumar <[email protected]>
Acked-by: Simon Glass <[email protected]>
Tested-by: Simon Glass <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
Patch is the result of:
sed -i -e 's/FTDFILE/FDTFILE/g' board/sunxi/Kconfig configs/* include/configs/sunxi-common.h
sed -i -e 's/ftdfile/fdtfile/g' board/sunxi/Kconfig
Reported-by: Vagrant Cascadian <[email protected]>
Signed-off-by: Ian Campbell <[email protected]>
Acked-by: Hans de Goede <[email protected]>
[ ijc -- s/Spotted-by/Reported-by/ and resolve conflict vs "remove
redundant "SPL" from CONFIG_SYS_EXTRA_OPTIONS" ]
|
|
This config is valid for two devices:
- Odroid X2,
- Odroid U3.
Signed-off-by: Przemyslaw Marczak <[email protected]>
Cc: Minkyu Kang <[email protected]>
Cc: Tom Rini <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
To reduce code duplication update am335x_igep0033.h to use ti_am335x_common.h
and convert to generic board.
Signed-off-by: Enric Balletbo i Serra <[email protected]>
|
|
This patch adds boot script support to omap3 beagle board.
Signed-off-by: Guillaume GARDET <[email protected]>
Cc: Tom Rini <[email protected]>
|
|
|
|
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Nomadik board select menu to nomadik/Kconfig.
Move also common settings (CONFIG_SYS_CPU="arm926ejs" and
CONFIG_SYS_SOC="nomadik").
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Orion5x board select menu to orion5x/Kconfig.
Move also common settings (CONFIG_SYS_CPU="arm926ejs" and
CONFIG_SYS_SOC="orion5x").
Signed-off-by: Masahiro Yamada <[email protected]>
Cc: Albert ARIBAUD <[email protected]>
|
|
Becuase the board select menu in arch/arm/Kconfig is too big,
move the OMAP5 board select menu to omap5/Kconfig.
Move also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="omap5").
Signed-off-by: Masahiro Yamada <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Cc: Lokesh Vutla <[email protected]>
|
|
Becuase the board select menu in arch/arm/Kconfig is too big,
move the OMAP4 board select menu to omap4/Kconfig.
Move also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="omap4").
Signed-off-by: Masahiro Yamada <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Cc: Lokesh Vutla <[email protected]>
|
|
Becuase the board select menu in arch/arm/Kconfig is too big,
move the OMAP3 board select menu to omap3/Kconfig.
Move also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="omap3
Signed-off-by: Masahiro Yamada <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Becuase the board select menu in arch/arm/Kconfig is too big,
move the KirkWood board select menu to kirkwood/Kconfig.
Consolidate also common settings (CONFIG_SYS_CPU="arm926ejs" and
CONFIG_SYS_SOC="kirkwood").
Signed-off-by: Masahiro Yamada <[email protected]>
Acked-by: Prafulla Wadasdkar <[email protected]>
Cc: Luka Perkov <[email protected]>
|
|
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Rmobile board select menu to rmobile/Kconfig.
Consolidate also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="rmobile").
Signed-off-by: Masahiro Yamada <[email protected]>
Cc: Nobuhiro Iwamatsu <[email protected]>
|
|
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Tegra board select menu to tegra/Kconfig.
Insert the Tegra SoC select menu between the arch select and the
board select.
Architecture select
|-- Tegra Platform (Tegra)
|- Tegra SoC select (Tegra20 / 30 / 114 / 124)
|- Board select
Consolidate also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="tegra*") and always "select" CONFIG_SPL as follows:
config TEGRA
bool
select SPL
Signed-off-by: Masahiro Yamada <[email protected]>
Acked-by: Stephen Warren <[email protected]>
Cc: Tom Warren <[email protected]>
|
|
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Zynq board select menu to zynq/Kconfig.
Consolidate also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="zynq").
Refactor board/xilinx/zynq/MAINTAINERS too.
Signed-off-by: Masahiro Yamada <[email protected]>
Tested-by: Michal Simek <[email protected]>
|
|
Newer FLASH types used on these boards don't allow writing of subpages.
So disable subpage write in the NAND driver. Additionally we need to
tell the UBI layer in the kernel that he also should only write 2048
bytes. This is done with an additional command line parameter for the
kernel commandline.
Signed-off-by: Holger Brunck <[email protected]>
cc: Valentin Longchamp <[email protected]>
cc: Prafulla Wadaskar <[email protected]>
|
|
Add support for booting Images and for unzipping Image.gz files.
Signed-off-by: Tom Rini <[email protected]>
|
|
- Drop DEBUG
- Drop defines we can use the default of.
- Provide a larger malloc pool.
- Correct default locations for kernel / initrd / device tree
Signed-off-by: Tom Rini <[email protected]>
|
|
The bcm_ep board configuration is used by a number of boards
including Cygnus and NSP.
Add builds for the bcm958300k and the bcm958622hr boards.
Signed-off-by: Scott Branden <[email protected]>
Signed-off-by: Steve Rae <[email protected]>
|
|
To enable hypervisors utilizing the ARMv7 virtualization extension
on the Arndale board, add the simple SMP pen address writer function
and add the required configuration variables to switch all cores to
HYP mode before launching the OS.
This allows booting KVM and Xen directly from u-boot.
Reviewed-by: Christoffer Dall <[email protected]>
Signed-off-by: Andre Przywara <[email protected]>
Signed-off-by: Christoffer Dall <[email protected]>
Signed-off-by: Andre Przywara <[email protected]>
|
|
Enable initialization fo designware ethernet controller. With this
patch, ethernet works in my configuration, provided I set ethernet
address in the environment.
Signed-off-by: Pavel Machek <[email protected]>
|
|
Though nios2-generic board meant to be a template, it is helpful
to be able to test on a real hardware. As the nios2 linux is
developed and tested on a 3c120 FPGA based Golden Hardware Reference
Design, it makes sense to rebase nios2-generic on this FPGA design.
Signed-off-by: Thomas Chou <[email protected]>
|
|
To fix the build error when build for Altera dev kit, not
virtual target. At same time, set the build for Altera dev
kit as default instead virtual target. With that, U-Boot
is booting well and SPL still lack of few drivers.
Signed-off-by: Chin Liang See <[email protected]>
Cc: Pavel Machek <[email protected]>
Cc: Marek Vasut <[email protected]>
Cc: Tom Rini <[email protected]>
Cc: Albert Aribaud <[email protected]>
|
|
|
|
|
|
|
|
|
|
The commit (SHA1: 8fc171318e352) reintroduced correct values for vendor and
product IDs required for UMS gadget to work properly either at Windows or
Linux.
This data was missing for GONI target, so this commit corrects this mistake.
Signed-off-by: Lukasz Majewski <[email protected]>
Acked-by: Robert Baldyga <[email protected]>
Acked-by: Minkyu Kang <[email protected]>
|
|
|
|
Include general configs/ti_am335x_common.h and drop redundant #defines.
Signed-off-by: Matwey V. Kornilov <[email protected]>
|
|
DRA7 evm REV G and later boards uses a vtt regulator for DDR3 termination
and this is controlled by gpio7_11. Configuring gpio7_11.
The pad A22(offset 0x3b4) is used by gpio7_11 on REV G and later boards,
and left unused on previous boards, so it is safe enough to enable gpio
on all DRA7 boards.
Signed-off-by: Lokesh Vutla <[email protected]>
|
|
Use generic board setup functions by defining
CONFIG_SYS_GENERIC_BOARD.
Signed-off-by: Dmitry Lifshitz <[email protected]>
|
|
Cc: Raphael Assenat <[email protected]>
Cc: Stefano Babic <[email protected]>
Signed-off-by: Jeroen Hofstee <[email protected]>
|
|
This patch adds support for parallel NOR device (S29GL512S10) present on J6-EVM.
The Flash device is connected to GPMC controller on chip-select[0] and accessed
as memory-mapped device. It has data-witdh=x16, capacity-64MBytes(512Mbits) and
is CFI compatible.
As multiple devices are share GPMC pins on this board, so following board
settings are required to detect NOR device:
SW5.1 (NAND_BOOTn) = OFF (logic-1)
SW5.2 (NOR_BOOTn) = ON (logic-0) /* Active-low */
SW5.3 (eMMC_BOOTn) = OFF (logic-1)
SW5.4 (QSPI_BOOTn) = OFF (logic-1)
And also set appropriate SYSBOOT configurations:
SW3.1 (SYSBOOT[ 8])= ON (logic-1) /* selects SYS_CLK1 speed */
SW3.2 (SYSBOOT[ 9])= OFF (logic-0) /* selects SYS_CLK1 speed */
SW3.3 (SYSBOOT[10])= ON (logic-1) /* wait-pin monitoring = enabled */
SW3.4 (SYSBOOT[11])= OFF (logic-0) /* device type: Non Muxed */
SW3.5 (SYSBOOT[12])= OFF (logic-0) /* device type: Non Muxed */
SW3.6 (SYSBOOT[13])= ON (logic-1) /* device bus-width: 1(x16) */
SW3.7 (SYSBOOT[14])= OFF (logic-0) /* reserved */
SW3.8 (SYSBOOT[15])= ON (logic-1) /* reserved */
Also, following changes are required to enable NOR Flash support in
dra7xx_evm board profile:
|
|
This patch adds support for x16 NAND device (MT29F2G16AAD) connected to GPMC
chip-select[0] on DRA7xx EVM.
As GPMC pins are shared by multiple devices, so in addition to this patch
following board settings are required for NAND device detection [1]:
SW5.9 (GPMC_WPN) = OFF (logic-1)
SW5.1 (NAND_BOOTn) = ON (logic-0) /* Active-low */
SW5.2 (NOR_BOOTn) = OFF (logic-1)
SW5.3 (eMMC_BOOTn) = OFF (logic-1)
SW5.4 (QSPI_BOOTn) = OFF (logic-1)
And also set appropriate SYSBOOT configurations
SW2.1 (SYSBOOT[0]) = ON (logic-1) /* selects NAND Boot */
SW2.2 (SYSBOOT[1]) = OFF (logic-0) /* selects NAND Boot */
SW2.3 (SYSBOOT[2]) = OFF (logic-0) /* selects NAND Boot */
SW2.4 (SYSBOOT[3]) = OFF (logic-0) /* selects NAND Boot */
SW2.5 (SYSBOOT[4]) = ON (logic-1) /* selects NAND Boot */
SW2.6 (SYSBOOT[5]) = ON (logic-1) /* selects NAND Boot */
SW2.7 (SYSBOOT[6]) = OFF (logic-0) /* reserved */
SW2.8 (SYSBOOT[7]) = OFF (logic-0) /* reserved */
SW3.1 (SYSBOOT[ 8])= ON (logic-1) /* selects SYS_CLK1 speed */
SW3.2 (SYSBOOT[ 9])= OFF (logic-0) /* selects SYS_CLK1 speed */
SW3.3 (SYSBOOT[10])= ON (logic-1) /* wait-pin monitoring = enabled */
SW3.4 (SYSBOOT[11])= OFF (logic-0) /* device type: Addr/Data Muxed */
SW3.5 (SYSBOOT[12])= ON (logic-1) /* device type: Addr/Data Muxed */
SW3.6 (SYSBOOT[13])= ON (logic-1) /* device bus-width: 1(x16) */
SW3.7 (SYSBOOT[14])= OFF (logic-0) /* reserved */
SW3.8 (SYSBOOT[15])= ON (logic-1) /* reserved */
Following changes are required in board.cfg to enable NAND on J6-EVM:
|
