| Age | Commit message (Collapse) | Author |
|---|
|
This patch adds support for NAND device connected to GPMC chip-select on
following AM43xx EVM boards.
am437x-gp-evm: On this board, NAND Flash signals are muxed with eMMC, thus at a
time either eMMC or NAND can be enabled. Selection between eMMC and NAND is
controlled by:
(a) Statically using Jumper on connecter (J89) present on board.
(a) If Jumper on J89 is NOT used, then selection can be dynamically controlled
by driving SPI2_CS0[MUX_MODE=GPIO] pin via software:
SPI2_CS0 == 0: NAND (default)
SPI2_CS0 == 1: eMMC
am43x-epos-evm: On this board, NAND Flash control lines are muxed with QSPI,
Thus only one of the two can be used at a time. Selection is controlled by:
(a) Dynamically driving following GPIO pin from software
GPMC_A0(GPIO) == 0 NAND is selected (default)
NAND device (MT29F4G08AB) on these boards has:
- data-width=8bits
- blocksize=256KB
- pagesize=4KB
- oobsize=224 bytes
For above NAND device, ROM code expects the boot-loader to be flashed in BCH16
ECC scheme for NAND boot, So by default BCH16 ECC is enabled for AM43xx EVMs.
Signed-off-by: Pekon Gupta <[email protected]>
|
|
This patch
- consolidate CONFIG_SYS_NAND_xx and CONFIG_SPL_NAND_xx from various
configuration files into single file.
- update MTD Partition table to match AM335x_EVM DT in linux-kernel
- segregate CONFIGs based on different boot modes (like SPL and U-Boot)
Signed-off-by: Pekon Gupta <[email protected]>
|
|
When we're using EMMC_BOOT that means we have environment on eMMC so
we can make use of CONFIG_SPL_ENV_SUPPORT within Falcon Mode.
Signed-off-by: Tom Rini <[email protected]>
|
|
In the case of SPL on these boards we only need environment for
SPL_USBETH, so it's safe to normally use ENV_IS_NOWHERE and SPL+NAND
does not support environment today.
Cc: Hannes Petermaier <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
There are times where we may need more than a few kilobytes of stack
space. We also will not be using CONFIG_SPL_STACK location prior to DDR
being initialized (CONFIG_SYS_INIT_SP_ADDR is still used there) so pick
a good location within DDR for this to be. Tested on
OMAP4/AM335x/OMAP5/DRA7xx.
Signed-off-by: Tom Rini <[email protected]>
|
|
On am335x_evm we only support USBETH for a networking SPL option so move
the rest of the defines under that area as that's the only time we need
(and want) environment support here.
Signed-off-by: Tom Rini <[email protected]>
|
|
|
|
This patch implements the generic board init as described in
doc/README.generic-board.
Signed-off-by: Thomas Chou <[email protected]>
Signed-off-by: Scott McNutt <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Signed-off-by: Thomas Chou <[email protected]>
|
|
This board has been orphaned for a while and old enough.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
These boards have been orphaned for a while and old enough.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
This board has been orphaned for a while and old enough.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
This board has been orphaned for a while and old enough.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
This board has been orphaned for a while and old enough.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Emails to the board maintainer
"Rishi Bhattacharya <[email protected]>"
have been bouncing.
Tom suggested to remove this board.
Remove also omap1510_udc.c because this is the last board
to enable it.
Signed-off-by: Masahiro Yamada <[email protected]>
Suggested-by: Tom Rini <[email protected]>
|
|
|
|
When u-boot initializes the RAM (early in boot) it looks for the "pram"
env variable to know which is area it cannot use. If the "pram" env variable
is not found, the default CONFIG_PRAM value is used.
This value used to be 0 (no protection at all). This patch sets it to a
value that covers PHRAM and PNVRAM that must be protected in our case.
Signed-off-by: Valentin Longchamp <[email protected]>
Signed-off-by: Holger Brunck <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
mx6sxsabresd board has 2 FEC ports, each one connected to a AR8031.
Add support for one FEC port initially.
Signed-off-by: Fabio Estevam <[email protected]>
|
|
It is necessary to provide the same Vendor and Product IDs as the one in
the original Linux kernel code.
Without this change the USB mass storage gadget is not working with Windows7.
Signed-off-by: Lukasz Majewski <[email protected]>
Acked-by: Minkyu Kang <[email protected]>
|
|
The Gateworks Ventana EEPROM contains a set of configuration bits that
affect the removal of device-tree nodes that support peripherals that do not
exist on sub-loaded boards. This patch adds:
- a structure to define a config bit name, dt node alias, bit position
- an array of supported configuration items
- an econfig command to get/set/list configuration bits
- use of the array when adjusting the FDT prior to boot
Signed-off-by: Tim Harvey <[email protected]>
|
|
Building the SPL in Thumb mode saves roughly 30% in size of the
resulting SPL binary. As the size of SPL it limited on the MX6,
this helps a lot.
Signed-off-by: Marek Vasut <[email protected]>
Acked-by: Tim Harvey <[email protected]>
|
|
This allows u-boot to load different OS or Bare Metal application on
different cores of the i.MX6 SoC.
For example: running Android on cpu0 and a RT OS like QNX/FreeRTOS on cpu1.
Signed-off-by: Gabriel Huau <[email protected]>
Acked-by: Stefano Babic <[email protected]>
|
|
This adds board support for the Toradex Colibri T30 module.
Working functions:
- SD card boot
- eMMC environment and boot
- USB host/USB client (on the dual role port)
- Network (via ASIX USB)
Signed-off-by: Stefan Agner <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
Enable DFU protocol support (via the "dfu" command) on Tegra boards where
USB device/gadget mode is enabled.
Note that for DFU to operate correctly on Tegra, we still need some DFU
fixes/enhancements that are going through the DFU -> USB trees. However,
the code builds just fine without those changes, and applying this patch
now will allow both sets of patches to meet in the main U-Boot tree much
more quickly.
In order to run test/dfu/dfu_gadget_test.sh, you would need to add the
following to the board configuration:
CONFIG_EXT4_WRITE
CONFIG_CMD_EXT4_WRITE
However, I haven't enabled those here, since I believe the main use-case
for DFU on Tegra is raw flash writing, rather than filesystem access, so
we don't need the additional code-size hit. However, I could be persuaded
otherwise! We should probably add a separate test script for raw flash
access.
Signed-off-by: Stephen Warren <[email protected]>
Acked-by: Simon Glass <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
Set CONFIG_BOARD_SIZE_LIMIT so we'll notice at build time if U-Boot
has grown so large that it would overlap with the environment area in
flash, rather than bricking the device at run-time on first saveenv.
Signed-off-by: Sascha Silbe <[email protected]>
|
|
|
|
Add deep sleep support in SPI/SD boot. The destination address
second stage uboot image is loaded to is changed because
currently this address will be used by kernel which means
we can't reserve it for resume.
Entry point to kernel is still placed in second stage uboot.
Signed-off-by: Tang Yuantian <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
T1042 has internal display interface unit (DIU) for driving video.
T1042RDB supports video mode via
-LCD using TI enconder
-HDMI type interface via HDMI encoder
Chrontel, CH7301C encoder which is I2C programmable is used
as HDMI connector on T1042RDB.
This patch add support to
-enable Video interface for T1042RDB
-route qixis multiplexing to enable DIU-HDMI interface on board
-program DIU pixel clock gerenartor for T1042
-program HDMI encoder via I2C on board
This patch refer to the upstream diu patch
(337b0c52b3296f371d04aef71a833e09110e0e6b) for T1040qds.
Signed-off-by: Jason Jin <[email protected]>
Signed-off-by: Wang Dongsheng <[email protected]>
[York Sun: resolve conflict and move changes to T104xRDB.h]
Reviewed-by: York Sun <[email protected]>
|
|
The ch7301 encoder not only used in t1040qds platform, so we split
it for t1042rdb and LSx platform.
Signed-off-by: Wang Dongsheng <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
Automatic booting using an extlinux.conf file requires various environment
variables to be set.
Also modify CONFIG_SYS_LOAD_ADDR and CONFIG_STANDALONE_LOAD_ADDR to match
the value chosen for kernel_addr_r, see the added comment for why the new
value is chosen.
Signed-off-by: Hans de Goede <[email protected]>
Acked-by: Stephen Warren <[email protected]>
|
|
Use the new standard bootcmd from <config_distro_bootcmd.h>.
Signed-off-by: Hans de Goede <[email protected]>
Acked-by: Stephen Warren <[email protected]>
|
|
config_distro_defaults.h which is include later will redefine CONFIG_CMD_NET,
drop the useless / meaningless undef of it.
While at also move the undef of CONFIG_CMD_FPGA up to directly under the
include of config_cmd_defaults.h, to make it clear that it overwrites
the setting done from config_cmd_defaults.h .
Signed-off-by: Hans de Goede <[email protected]>
Acked-by: Ian Campbell <[email protected]>
|
|
I see no reason to override the choice to include this from
config_cmd_defauls.h .
Signed-off-by: Hans de Goede <[email protected]>
Acked-by: Ian Campbell <[email protected]>
|
|
We undef CONFIG_CMD_NET at line 167, and there is nothing re-defining it
between line 167 and the #ifdef CONFIG_CMD_NET, so remove this effectively
dead block.
Signed-off-by: Hans de Goede <[email protected]>
Acked-by: Ian Campbell <[email protected]>
|
|
sunxi does not need this and it should never have been enabled for it in
the first place.
Signed-off-by: Hans de Goede <[email protected]>
Acked-by: Ian Campbell <[email protected]>
|
|
Conflicts:
boards.cfg
Signed-off-by: Stefano Babic <[email protected]>
|
|
Replace the custom $bootcmd with that from <config_distro_bootcmd.h>.
There should be no functional change, since the new generic $bootcmd was
derived strongly from tegra-common-post.h, after which this part of
rpi_b.h was modelled.
The #defines to enable/disable U-Boot commands/features were moved
earlier in rpi_b.h, so they are set up before config_distro_bootcmd.h
is included, since it tests whether certain features should be included
based on those defines.
Signed-off-by: Stephen Warren <[email protected]>
Acked-by: Simon Glass <[email protected]>
|
|
Replace the custom $bootcmd with that from <config_distro_bootcmd.h>.
There should be no functional change, since the new generic $bootcmd was
derived strongly from tegra-common-post.h.
Signed-off-by: Stephen Warren <[email protected]>
Acked-by: Simon Glass <[email protected]>
|
|
The following configs are not defined at all.
- CONFIG_OMAP1510
- CONFIG_OMAP_1510P1
- CONFIG_OMAP_SX1
- CONFIG_OMAP3_DMA
- CONFIG_OMAP3_ZOOM2
- CONFIG_OMAP_INNOVATOR
Signed-off-by: Masahiro Yamada <[email protected]>
Cc: Tom Rini <[email protected]>
|
|
After the clean up performed in the commit 1151b7ac10b81ecbb the DFU subsystem
requires absolute patch for correct operation.
Signed-off-by: Lukasz Majewski <[email protected]>
|
|
echi-rmobile does not support xHCI. This removes xHCI address
from address table. And this revise a value of CONFIG_USB_MAX_CONTROLLER_COUNT
for lager board and koelsh board.
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
|
|
Enable CONFIG_SYS_GENERIC_BOARD for the i.MX31 PDK board.
Tested on actual hardware.
Signed-off-by: Magnus Lilja <[email protected]>
Acked-by: Fabio Estevam <[email protected]>
|
|
A previous update to the I2C stack introduced a typo in the
configuration option. Fix the typo and therefore allow the
RTC to work correctly with the 'date' command again.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Stefano Babic <[email protected]>
|
|
|
|
functions
- move blackfin specific cpu init code from blackfin board.c to cpu.c
- remove blackfin specific board init code and invoke generic board_f fron cpu init entry
- rename section name bss_vma to bss_start in order to match the generic board init code
- add a fake relocate_code function to set up the new stack only
Signed-off-by: Sonic Zhang <[email protected]>
|
|
|
|
The booting of the board is now protected by the CPU watchdog.
A failure during the boot phase will end up in board reset.
Signed-off-by: Rainer Boschung <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
This patch add Marvell kirkwood MVSDIO/MMC driver
and enable it for Sheevaplugs and OpenRD boards.
Signed-off-by: Gerald Kerma <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
Acked-by: Pantelis Antoniou <[email protected]>
|
|
CNTFRQ needs to be properly configured on all CPUs. Otherwise,
virtual machines hoping to find valuable information on secondary
CPUs will be disapointed...
Signed-off-by: Marc Zyngier <[email protected]>
Acked-by: Hans de Goede <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
|
