| Age | Commit message (Collapse) | Author |
|---|
|
When the ti814x_evm config was removed most, but not all, of the
relevant support code was remove. Get rid of what was missed.
Fixes: 50b532686849 ("ti814x: Remove platform")
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_PEN_ADDR_BIG_ENDIAN
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_OVERWRITE_ETHADDR_ONCE
Signed-off-by: Tom Rini <[email protected]>
|
|
Enable this in the board Kconfig file, but then check for it via
CONFIG_IS_ENABLED so that it will only be true in the non-SPL case, as
is done today. As part of this we move some defines local to where
they are used as it's board specific.
Cc: Samuel Egli <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_MXC_NAND_HWECC
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_MONITOR_IS_IN_RAM
As part of this, reword some of the documentation slightly to reflect
that this is in Kconfig and not a define now.
Signed-off-by: Tom Rini <[email protected]>
|
|
The way all of the memory init code here works is that we pass
0xDEADBEEF around for the initial value (as it's a well known 'poison'
value and so easily recognized in debuggers, etc). The only point of
this CONFIG symbol was to pass in a different value for that purpose.
Drop this symbol and cleanup the code slightly.
Signed-off-by: Tom Rini <[email protected]>
|
|
Fixup this last remnant of CONFIG_MALTA.
Cc: Paul Burton <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_L2_CACHE
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_KSNET_NETCP_V1_0
CONFIG_KSNET_NETCP_V1_5
Signed-off-by: Tom Rini <[email protected]>
|
|
This removes the following unreferenced CONFIG symbols:
CONFIG_FDTADDR
CONFIG_FDTFILE
CONFIG_FLASH_SECTOR_SIZE
CONFIG_FSL_CPLD
CONFIG_HDMI_ENCODER_I2C_ADDR
CONFIG_I2C_MVTWSI
CONFIG_I2C_RTC_ADDR
CONFIG_IRAM_END
CONFIG_IRAM_SIZE
CONFIG_KSNET_MDIO_PHY_CONFIG_ENABLE
CONFIG_L1_INIT_RAM
CONFIG_MACB_SEARCH_PHY
CONFIG_MIU_2BIT_21_7_INTERLEAVED
CONFIG_MTD_NAND_VERIFY_WRITE
CONFIG_MVGBE_PORTS
CONFIG_NETDEV
CONFIG_NUM_DSP_CPUS
CONFIG_PHY_BASE_ADR
CONFIG_PHY_INTERFACE_MODE
CONFIG_PSRAM_SCFG
CONFIG_RAMBOOT_SPIFLASH
CONFIG_RAMBOOT_TEXT_BASE
CONFIG_RD_LVL
CONFIG_ROCKCHIP_SDHCI_MAX_FREQ
CONFIG_SETUP_INITRD_TAG
CONFIG_SH_QSPI_BASE
CONFIG_SMDK5420
CONFIG_SOCRATES
CONFIG_SPI_ADDR
CONFIG_SPI_FLASH_QUAD
CONFIG_SPI_FLASH_SIZE
CONFIG_SPI_HALF_DUPLEX
CONFIG_SPI_N25Q256A_RESET
CONFIG_TEGRA_SLINK_CTRLS
CONFIG_TPM_TIS_BASE_ADDRESS
CONFIG_UBOOT_SECTOR_COUNT
CONFIG_UBOOT_SECTOR_START
CONFIG_VAR_SIZE_SPL
CONFIG_VERY_BIG_RAM
And also:
BL1_SIZE
PHY_NO
RESERVE_BLOCK_SIZE
Signed-off-by: Tom Rini <[email protected]>
|
|
This functionality is part of the legacy I2C subsystem and is currently
unused anywhere. Remove the remaining references.
Signed-off-by: Tom Rini <[email protected]>
|
|
Following how g_dnl_bind_fixup is used on other platforms, rename the
unchanging defines used here to be prefixed with EXYNOS rather than
Samsung, and define them here.
Cc: Minkyu Kang <[email protected]>
Cc: Jaehoon Chung <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_GATEWAYIP
CONFIG_HOSTNAME
CONFIG_IPADDR
CONFIG_NETMASK
CONFIG_ROOTPATH
CONFIG_SERVERIP
CONFIG_UBOOTPATH
To do this, we introduce a CONFIG_USE_ form of each of the above and
change include/env_default.h to test for that to be set before setting a
value. Further, we don't want to stringify the IP address related values
as they are now properly strings via Kconfig.
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_POWER_PCA9450
Signed-off-by: Tom Rini <[email protected]>
|
|
CONFIG_SYS_BAUDRATE_TABLE has already been migrated to CFG_SYS but this
instance was missed, correct.
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_FSL_ESDHC_PIN_MUX
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_FLASH_SPANSION_S29WS_N
CONFIG_FLASH_VERIFY
CONFIG_FSL_FM_10GEC_REGULAR_NOTATION
CONFIG_FSL_ISBC_KEY_EXT
CONFIG_FSL_TRUST_ARCH_v1
CONFIG_FSL_SDHC_V2_3
CONFIG_MAX_DSP_CPUS
CONFIG_MIU_2BIT_INTERLEAVED
CONFIG_SERIAL_BOOT
CONFIG_SPI_BOOTING
CONFIG_X86EMU_RAW_IO
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_FLASH_SHOW_PROGRESS
Signed-off-by: Tom Rini <[email protected]>
|
|
This option is only used on one platform currently. However, with PHYLIB
enabled, which this platform also does, this option is not checked and
the functional use case is handled. Remove this code.
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_DM9000_BYTE_SWAPPED
CONFIG_DM9000_NO_SROM
CONFIG_DM9000_USE_16BIT
CONFIG_DM9000_DEBUG
CONFIG_MXC_GPT_HCLK
CONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECC
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_HSMMC2_8BIT
Signed-off-by: Tom Rini <[email protected]>
|
|
Only this platform sets mmcdev via CONFIG_MMC_DEFAULT_DEV so we
hard-code that default directly.
Signed-off-by: Tom Rini <[email protected]>
|
|
The symbols CONFIG_UBI_PART and CONFIG_UBIFS_VOLUME are not referenced
anywhere, drop them.
Signed-off-by: Tom Rini <[email protected]>
|
|
The CONFIG_USB_FAT_BOOT, CONFIG_USB_EXT2_BOOT and CONFIG_NORBOOT defines
are not referenced anywhere, so remove them.
Signed-off-by: Tom Rini <[email protected]>
|
|
This symbol is enabled for all exynos5 platforms, move to Kconfig and
select it.
Cc: Jaehoon Chung <[email protected]>
Cc: Minkyu Kang <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Prepare v2023.01-rc4
Signed-off-by: Tom Rini <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-rockchip
- Only call binman when TPL available;
- rk3128 DTS fix;
- Fix GPT table corruption for rk3399 puma ;
- Fix i2c for rk3399 Pinebookpro;
- Enable UEFI capsule update for RockPi4;
|
|
Add information that will be needed for enabling the UEFI capsule
update feature on the RockPi4 boards. With the feature enabled, it
would be possible to update the idbloader and u-boot.itb images on the
RockPi4B and RockPi4C variants.
Signed-off-by: Sughosh Ganu <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
There is a CONFIG_MMC_SUNXI_SLOT definition in our sunxi_common.h config
header, which was used to note the first MMC controller to initialise.
The definition in that header was always set to 0, with no easy way of
overriding this, and certainly none of the existing boards made any use
of that (non-)feature.
Remove that definition and replace it with a constant 0 in the only
user, in board.c. It turns out that this is safe, as this is only used
in the SPL, and the BROM also unconditionally initialises MMC0.
This also removes the last legacy config symbol with SUN*I in it from
the whitelist.
Reviewed-by: Samuel Holland <[email protected]>
Tested-by: Samuel Holland <[email protected]>
Signed-off-by: Andre Przywara <[email protected]>
|
|
These are unused defines and can be dropped.
Signed-off-by: Holger Brunck <[email protected]>
|
|
Enable DM_I2C and I2C mux to get rid of the usage of the legacy
i2c driver.
Signed-off-by: Holger Brunck <[email protected]>
|
|
Instead of having these defines in a header file, move them to
a simple text file.
Signed-off-by: Holger Brunck <[email protected]>
|
|
Use like the other boards a text file for the environment.
As this is the last user of keymile-common.h we can now remove this
file completely.
Signed-off-by: Holger Brunck <[email protected]>
|
|
Use already present common.env file and add a powerpc specific env
so that we can move all the environment defines to text files.
Signed-off-by: Holger Brunck <[email protected]>
|
|
Create a common.env which we can use later on also for other boards.
Signed-off-by: Holger Brunck <[email protected]>
|
|
Replace MTDPARTS_DEFAULT in the config include file by
CONFIG_MTDPARTS_DEFAULT in defconfig to complete the Kconfig migration.
Signed-off-by: Patrick Delaunay <[email protected]>
|
|
Replace MTDPARTS_DEFAULT in the config include file by
CONFIG_MTDPARTS_DEFAULT in defconfig to complete the Kconfig migration.
Signed-off-by: Patrick Delaunay <[email protected]>
|
|
Replace MTDIDS_DEFAULT and MTDPARTS_DEFAULT in the config include file by
CONFIG_MTDIDS_DEFAULT and CONFIG_MTDPARTS_DEFAULT in defconfig to complete
the Kconfig migration.
Signed-off-by: Patrick Delaunay <[email protected]>
|
|
Replace MTDIDS_DEFAULT in config include file by CONFIG_MTDIDS_DEFAULT
in defonfig to complete the Kconfig migration
Signed-off-by: Patrick Delaunay <[email protected]>
|
|
Introduce the minimum configs, only SD-MMC and UART boot related
settings, to serve as a good starting point for the am62a as we add more
functionality.
Signed-off-by: Bryan Brattlof <[email protected]>
[trini: Disable CONFIG_NET as it's not used, in both platforms]
Signed-off-by: Tom Rini <[email protected]>
|
|
Move this out of board file as this is done by the DM based NAND flash
driver. The EBI chip select configuration, iomux and timings are
handled by the driver
Signed-off-by: Balamanikandan Gunasundar <[email protected]>
|
|
As DM_ETH is required for all network drivers, it's now safe to remove
the non-DM_ETH support code. Doing this removes some board support code
which was also unused. Finally, this removes some CONFIG symbols that
otherwise needed to be migrated to Kconfig, but were unused in code now.
Signed-off-by: Tom Rini <[email protected]>
|
|
In practice, it is clear that the usage in m68k of
CONFIG_WATCHDOG_TIMEOUT is setting a value in milliseconds. Rename this
to the existing symbol and move to Kconfig.
Signed-off-by: Tom Rini <[email protected]>
|
|
We move the existing CONFIG_POST_* functionality over to CFG_POST and
then introduce CONFIG_POST to Kconfig.
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Given that we can use Kconfig logic directly to see if we have a program
available on the host or not, change from passing NO_SDL to instead
controlling CONFIG_SANDBOX_SDL in Kconfig directly. Introduce
CONFIG_HOST_HAS_SDL as the way to test for sdl2-config and default
CONFIG_SANDBOX_SDL on if we have that, or not.
Cc: Simon Glass <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Perform some deeper investigation on the remaining symbols listed in
this file and remove more.
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_VSC7385_ENET
CONFIG_VSC9953
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_USB_GADGET_AT91
Signed-off-by: Tom Rini <[email protected]>
|
|
Move a number of legacy USB UDC options to Kconfig, over from the config
header.
Cc: Pali Rohár <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
