| Age | Commit message (Collapse) | Author |
|---|
|
We're already relying on gd->cyclic being NULL before cyclic_init() is
called - i.e., we're relying on all of gd being zeroed before entering
any C code. And when we do populate gd->cyclic, its ->cyclic_ready
member is automatically set to true. So we can actually just rely on
testing gd->cyclic itself.
The only wrinkle is that cyclic_uninit() actually did set
->cyclic_ready to false. However, since it doesn't free gd->cyclic,
the cyclic infrastructure is actually still ready (i.e., the list_head
is properly initialized as an empty list).
Signed-off-by: Rasmus Villemoes <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
Tested-by: Stefan Roese <[email protected]>
Tested-by: Tim Harvey <[email protected]> # imx8mm-venice-*
|
|
As a preparation for future patches, use a flag in gd->flags rather
than a separate member in (the singleton) struct cyclic_drv to keep
track of whether we're already inside cyclic_run().
Signed-off-by: Rasmus Villemoes <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
Tested-by: Stefan Roese <[email protected]>
Tested-by: Tim Harvey <[email protected]> # imx8mm-venice-*
|
|
The FWU Multi Bank Update feature supports updating firmware images
to one of multiple sets(also called banks) of images. The firmware
images are clubbed together in banks, with the system booting images
from the active bank. Information on the images such as which bank
they belong to is stored as part of the metadata structure, which is
stored on the same storage media as the firmware images on a dedicated
partition.
At the time of update, the metadata is read to identify the bank to
which the images need to be flashed(update bank). On a successful
update, the metadata is modified to set the updated bank as active
bank to subsequently boot from.
Signed-off-by: Sughosh Ganu <[email protected]>
Acked-by: Ilias Apalodimas <[email protected]>
|
|
The FWU Multi Bank Update specification requires the Update Agent to
carry out certain checks at the time of platform boot. The Update
Agent is the component which is responsible for updating the firmware
components and maintaining and keeping the metadata in sync.
The spec requires that the Update Agent perform the following checks
at the time of boot
* Sanity check of both the metadata copies maintained by the platform.
* Get the boot index passed to U-Boot by the prior stage bootloader
and use this value for metadata bookkeeping.
* Check if the system is booting in Trial State. If the system boots
in the Trial State for more than a specified number of boot counts,
change the Active Bank to be booting the platform from.
Call these checks through the main loop event at the time of platform
boot.
Signed-off-by: Sughosh Ganu <[email protected]>
Reviewed-by: Etienne Carriere <[email protected]>
Acked-by: Ilias Apalodimas <[email protected]>
|
|
Add an event type EVT_MAIN_LOOP that can be used for registering
events that need to be run after the platform has been initialised and
before the main_loop function is called.
Signed-off-by: Sughosh Ganu <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Ilias Apalodimas <[email protected]>
Acked-by: Etienne Carriere <[email protected]>
|
|
The FWU Multi Bank Update feature allows the platform to boot the
firmware images from one of the partitions(banks). The first stage
bootloader(fsbl) passes the value of the boot index, i.e. the bank
from which the firmware images were booted from to U-Boot. On the
STM32MP157C-DK2 board, this value is passed through one of the SoC's
backup register. Add a function to read the boot index value from the
backup register.
Signed-off-by: Sughosh Ganu <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
Acked-by: Ilias Apalodimas <[email protected]>
Acked-by: Etienne Carriere <[email protected]>
|
|
Add weak functions for getting the update index value and dfu
alternate number needed for FWU Multi Bank update
functionality.
The current implementation for getting the update index value is for
platforms with 2 banks. If a platform supports more than 2 banks, it
can implement it's own function. The function to get the dfu alternate
number has been added for platforms with GPT partitioned storage
devices. Platforms with other storage partition scheme need to
implement their own function.
Signed-off-by: Sughosh Ganu <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
Acked-by: Etienne Carriere <[email protected]>
Reviewed-by: Ilias Apalodimas <[email protected]>
|
|
Enabling capsule update functionality on the platform requires
populating information on the images that are to be updated using the
functionality. Do so for the DK2 board.
Signed-off-by: Sughosh Ganu <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
Reviewed-by: Ilias Apalodimas <[email protected]>
Reviewed-by: Etienne Carriere <[email protected]>
|
|
In the FWU Multi Bank Update feature, the information about the
updatable images is stored as part of the metadata, on a separate
partition. Add a driver for reading from and writing to the metadata
when the updatable images and the metadata are stored on a block
device which is formatted with GPT based partition scheme.
Signed-off-by: Sughosh Ganu <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
Acked-by: Ilias Apalodimas <[email protected]>
|
|
In the FWU Multi Bank Update feature, the information about the
updatable images is stored as part of the metadata, which is stored on
a dedicated partition. Add the metadata structure, and a driver model
uclass which provides functions to access the metadata. These are
generic API's, and implementations can be added based on parameters
like how the metadata partition is accessed and what type of storage
device houses the metadata.
Signed-off-by: Sughosh Ganu <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
|
|
Add a VBE comment which shows the current state. Currently this is just
the phases which booted via VBE.
Signed-off-by: Simon Glass <[email protected]>
|
|
We expect VPL and SPL to load using VBE. Add a record of this so we can
check it in U-Boot proper.
Signed-off-by: Simon Glass <[email protected]>
|
|
Add an SPL loader to obtain the next-phase binary from a FIT provided
by the VBE driver.
Signed-off-by: Simon Glass <[email protected]>
|
|
VBE supports booting firmware during the SPL phases, i.e. so that VPL can
start SPL and SPL can start U-Boot.
It also supports booting an OS, when in U-Boot.
As a first step towards these features, add functions to indicate the
current VBE phase. The firmware selection is done in VPL and the OS
selection is done in U-Boot proper.
Signed-off-by: Simon Glass <[email protected]>
|
|
At present sandbox runs the next phase from discrete executables, so for
example u-boot-tpl runs u-boot-vpl to get to the next phase.
In some cases the phases are all built into a single firmware image, as is
done for real boards. Add support for this to sandbox.
Make it higher priority so that it takes precedence over the existing
method.
Signed-off-by: Simon Glass <[email protected]>
|
|
Add support for filtering out FIT images by phase. Rather than adding yet
another argument to this already overloaded function, use a composite
value, where the phase is only added in if needed.
The FIT config is still selected (and verified) as normal, but the images
are selected based on the phase.
Tests for this come in a little later, as part of the updated VPL test.
Signed-off-by: Simon Glass <[email protected]>
|
|
We want to be able to mark an image as related to a phase, so we can
easily load all the images for SPL or for U-Boot proper.
Add this to the FIT specification, along with some access functions.
Signed-off-by: Simon Glass <[email protected]>
|
|
At present sandbox only supports jumping to a file, to get to the next
U-Boot phase. We want to support other methods, so update the code to
use an enum for the method. Also use the
Use board_boot_order() to set the order, so we can add more options.
Also add the MMC methods into the BOOT_DEVICE enum so that booting
from MMC can be supported.
Signed-off-by: Simon Glass <[email protected]>
|
|
Move this comment to the header file, where the APIs should be defined.
Signed-off-by: Simon Glass <[email protected]>
|
|
Add test coverage for blk_write() as well.
The blk_erase() is not tested for now as the USB stor interface does not
support erase.
Signed-off-by: Simon Glass <[email protected]>
|
|
At present we have functions called blk_dread(), etc., which take a
struct blk_desc * to refer to the block device. Add some functions which
use udevice instead, since this is more in keeping with how driver model
is supposed to work.
Update one of the tests to use this.
Note that it would be nice to update the functions in disk-uclass.c to use
these new functions. However they are not quite the same. For example,
disk_blk_read() adds the partition offset to 'start' when calling the
cache read/fill functions, but does not with part_blk_read(), which does
the addition itself. So as designed the code is duplicated.
Signed-off-by: Simon Glass <[email protected]>
|
|
Use the uclass type as the first part of the function name, to be
consistent with the methods in other block drivers.
Signed-off-by: Simon Glass <[email protected]>
|
|
Add a function to init a bootflow, to reduce code duplication.
Signed-off-by: Simon Glass <[email protected]>
|
|
At present we normally write tests either in Python or in C. But most
Python tests end up doing a lot of checks which would be better done in C.
Checks done in C are orders of magnitude faster and it is possible to get
full access to U-Boot's internal workings, rather than just relying on
the command line.
The model is to have a Python test set up some things and then use C code
(in a unit test) to check that they were done correctly. But we don't want
those checks to happen as part of normal test running, since each C unit
tests is dependent on the associate Python tests, so cannot run without
it.
To acheive this, add a new UT_TESTF_MANUAL flag to use with the C 'check'
tests, so that they can be skipped by default when the 'ut' command is
used. Require that tests have a name ending with '_norun', so that pytest
knows to skip them.
Signed-off-by: Simon Glass <[email protected]>
|
|
At present it is possible for a test to skip itself by returning -EAGAIN
but this is not recorded. An existing example is in test_pre_run() with
the "Console recording disabled" check.
Keep a track of skipped tests and report the total at the end.
Signed-off-by: Simon Glass <[email protected]>
Acked-by: Heinrich Schuchardt <[email protected]>
|
|
At present we use symbols for the u-boot-spl entry, but this is not always
what we want. For example, sandbox actually jumps to a u-boot-spl-elf
entry, since sandbox executables are ELF files.
We already handle this with U-Boot by using the '-any' suffix. Add it for
SPL as well.
Signed-off-by: Simon Glass <[email protected]>
|
|
The current name is inconsistent with SPL which uses CONFIG_SPL_TEXT_BASE
and this makes it imposible to use CONFIG_VAL().
Rename it to resolve this problem.
Signed-off-by: Simon Glass <[email protected]>
|
|
BCM6753 is essentially same as the main chip BCM6855 but with different
SKU number. Now that BCM6855 is supported under CONFIG_ARCH_BCMBCA and
CONFIG_BCM6855, remove the original ARCH_BCM6753 support and migrate its
configuration and dts settings. This includes:
- Remove the bcm96753ref board folder. It is replaced by the
generic bcmbca board folder.
- Merge the 6753.dtsi setting to the new 6855.dtsi file. Update
96753ref board dts with the new compatible string.
- Delete broadcom_bcm96763ref.h and merge its setting to the new
bcm96855.h file.
- Delete bcm96753ref_ram_defconfig and use a basic config version of
bcm96855_defconfig
Signed-off-by: William Zhang <[email protected]>
Reviewed-by: Philippe Reynes <[email protected]>
|
|
BCM6855 is a Broadcom ARM A7 based PON Gateway SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family. Like other
broadband SoC, this patch adds it under CONFIG_BCM6855 chip config and
CONFIG_ARCH_BCMBCA platform config.
This initial support includes a bare-bone implementation and dts with
CPU subsystem, memory and ARM PL101 uart. This SoC is supported in the
linux-next git repository so the dts and dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <[email protected]>
Reviewed-by: Philippe Reynes <[email protected]>
|
|
Now that BCM6858 is supported under CONFIG_ARCH_BCMBCA and
CONFIG_BCM6858, remove the original ARCH_BCM6858 support and migrate its
configuration and dts settings. This includes:
- Remove the bcm968580xref board folder. It is replaced by the generic
bcmbca board folder.
- Update bcm968580xref board dts with the new compatible string.
- Delete broadcom_bcm968580xref.h and merge its setting to the new
bcm96858.h file.
- Remove bcm968580xref_ram_defconfig as a basic config version of
bcm96858_defconfig is now added.
Signed-off-by: William Zhang <[email protected]>
Reviewed-by: Philippe Reynes <[email protected]>
|
|
BCM6858 is a Broadcom B53 based PON Gateway SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family. Like other broadband
SoC, this patch adds it under CONFIG_BCM6858 chip config and
CONFIG_ARCH_BCMBCA platform config.
This initial support includes a bare-bone implementation and the
original dts is updated with the one from linux next git repository.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <[email protected]>
Reviewed-by: Philippe Reynes <[email protected]>
|
|
BCM68360 is a variant within the BCM6856 chip family. Now that BCM6856
is supported under CONFIG_ARCH_BCMBCA and CONFIG_BCM6856, remove the
original ARCH_BCM68360 support and migrate its configuration and dts
settings. This includes:
- Remove the bcm968360bg board folder. It is replaced by the generic
bcmbca board folder.
- Merge the 68360.dtsi setting to the new 6856.dtsi file. Update board
dts with the new compatible string.
- Merge broadcom_bcm968360bg.h setting to the new bcm96856.h file.
- Remove bcm968360bg_ram_defconfig as a basic config version of
bcm96856_defconfig is now added.
Signed-off-by: William Zhang <[email protected]>
Reviewed-by: Philippe Reynes <[email protected]>
|
|
BCM6856 is a Broadcom B53 based PON Gateway SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family. Like other Broadband
SoC, this patch adds it under CONFIG_BCM6856 chip config and
CONFIG_ARCH_BCMBCA platform config.
This initial support includes a bare-bone implementation and dts with
CPU subsystem, memory and Broadcom uart. This SoC is supported in the
linux-next git repository so the dts and dtsi files are copied from
linux.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <[email protected]>
Reviewed-by: Philippe Reynes <[email protected]>
|
|
Now that BCM63158 is supported under CONFIG_ARCH_BCMBCA and
CONFIG_BCM63158, remove the original ARCH_BCM63158 support and migrate
configuration settings.
Signed-off-by: William Zhang <[email protected]>
Reviewed-by: Philippe Reynes <[email protected]>
|
|
BCM63158 is a Broadcom B53 based DSL Gateway SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family. Like other
Broadband SoC, this patch adds it under CONFIG_BCM63158 chip
config and CONFIG_ARCH_BCMBCA platform config.
This initial support includes a bare-bone implementation and dts with
CPU subsystem, memory and ARM PL011 uart. This SoC is supported in the
linux-next git repository so the dts and dtsi files are copied from
linux.
The u-boot image can be loaded from flash or network to the entry
point address in the memory and boot from there to the console.
Signed-off-by: William Zhang <[email protected]>
Reviewed-by: Philippe Reynes <[email protected]>
|
|
BCM4908 is a Broadcom B53 based WLAN AP router SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family so it's added
under ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and Broadcom uart.
This SoC is supported in the linux git repository so the dts and dtsi
files are stripped down version of linux copies with mininum blocks
needed by u-boot.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
|
|
BCM6813 is a Broadcom B53 based PON and WLAN AP router SoC. It is part
of the BCA (Broadband Carrier Access origin) chipset family so it's
added under ARCH_BCMBCA platform. This initial support includes a
bare-bone implementation and dts with CPU subsystem, memory and ARM
PL011 uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
|
|
BCM4912 is a Broadcom B53 based WLAN AP router SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and ARM PL011 uart.
This SoC is supported in the linux-next git repository so the dts
and dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry
point address in the memory and boot from there to the console.
Signed-off-by: William Zhang <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
|
|
BCM63146 is a Broadcom B53 based DSL Broadband SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and ARM PL011 uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
|
|
BCM63138 is an ARM A9 based DSL Broadband SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory, ARM A9 global timer
and Broadcom uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are stripped down version of linux copies with mininum blocks
needed by u-boot.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
This patch applies on top of the my previous patch [1].
[1] https://lists.denx.de/pipermail/u-boot/2022-August/490570.html
Signed-off-by: William Zhang <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Reviewed-by: Philippe Reynes <[email protected]>
|
|
BCM63148 is an Broadcom B15 based DSL Broadband SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and Broadcom uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there.
Signed-off-by: William Zhang <[email protected]>
|
|
BCM6756 is an ARM A7 based WLAN Gateway and Access Point Broadband SoC.
It is part of the BCA(Broadband Carrier Access origin) chipset family so
it's added under ARCH_BCMBCA platform. This initial support includes a
bare-bone implementation and dts with CPU subsystem, memory and ARM
PL011 uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry
point address in the memory and boot from there.
Signed-off-by: William Zhang <[email protected]>
|
|
BCM6878 is an ARM A7 based PON Broadband SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and ARM PL011
uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux with minor fix-up that needs to be
upstreamed to linux as well.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there.
Signed-off-by: William Zhang <[email protected]>
|
|
BCM6846 is an ARM A7 based PON Broadband SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and Broadcom uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux with minor fix-up that needs to be
upstreamed to linux as well.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there.
Signed-off-by: William Zhang <[email protected]>
|
|
BCM63178 is an ARM A7 based DSL Broadband SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and ARM PL011 uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux with minor fix-up that needs to be
upstreamed to linux as well.
The u-boot image can be loaded from flash or network to the entry
point address in the memory and boot from there.
Signed-off-by: William Zhang <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-video
- fix [hv]sync active vs back porch in dw_mipi_dsi
- simplefb rotation support
- support splash as raw image from MMC
- enhancements to Truetype console (multiple fonts and sizes)
- drop old LCD support
|
|
Now that all the old code is gone, rename this option. Driver model
migration is now complete.
Signed-off-by: Simon Glass <[email protected]>
|
|
This is not used anymore. Drop it.
Signed-off-by: Simon Glass <[email protected]>
|
|
This code is no-longer used. Drop it.
Signed-off-by: Simon Glass <[email protected]>
|
|
This is used by the old LCD implementation which is to be removed.
Drop it and LCD_OUTPUT_BPP also.
Signed-off-by: Simon Glass <[email protected]>
|
