| Age | Commit message (Collapse) | Author |
|---|
|
https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request efi-2024-01-rc1
Documentation:
* Bump urllib3 version
* Migrate Renesas board docs to rst
* Link an introduction video
UEFI
* Use same GUID as EDK II for auto-created boot options
* Clean up BitBlt test
|
|
https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2024.01-rc1 v3
clk:
- remove additional compatible strings for Versal NET
net:
- zynq_gem: Fix clock calculation for MDC for higher frequencies
pinctrl:
- core: Extend pinmux status buffere size
- zynqmp driver: Show also tristate configuration
test:
- add test case for pxe get
Xilinx:
- describe SelectMAP boot mode
Zynq:
- Fix nand description in DT
ZynqMP:
- DTS sync patches with kernel and also W=1 related fixes
- Add support for KD240, zcu670, e-a2197 with x-prc cards, SC revB/C with i2c
description for other SC based boards
- k24 psu_init cleanup
|
|
This adds more supported spinand devices from the Linux kernel
implementation.
This does not include the latest kernel implementation as this would
require a substantial amount of extra work due to the missing
ECC engine abstraction layer in U-Boot.
Signed-off-by: Mikhail Kshevetskiy <[email protected]>
Signed-off-by: Frieder Schrempf <[email protected]> (commit message)
Link: https://lore.kernel.org/all/[email protected]
Signed-off-by: Dario Binacchi <[email protected]>
|
|
Currently there are 3 different variants of read_id implementation:
1. opcode only. Found in GD5FxGQ4xF.
2. opcode + 1 addr byte. Found in GD5GxGQ4xA/E
3. opcode + 1 dummy byte. Found in other currently supported chips.
Original implementation was for variant 1 and let detect function
of chips with variant 2 and 3 to ignore the first byte. This isn't
robust:
1. For chips of variant 2, if SPI master doesn't keep MOSI low
during read, chip will get a random id offset, and the entire id
buffer will shift by that offset, causing detect failure.
2. For chips of variant 1, if it happens to get a devid that equals
to manufacture id of variant 2 or 3 chips, it'll get incorrectly
detected.
This patch reworks detect procedure to address problems above. New
logic do detection for all variants separatedly, in 1-2-3 order.
Since all current detect methods do exactly the same id matching
procedure, unify them into core.c and remove detect method from
manufacture_ops.
This is a rework of Chuanhong Guo <[email protected]> patch
submitted to linux kernel
Signed-off-by: Mikhail Kshevetskiy <[email protected]>
Signed-off-by: Frieder Schrempf <[email protected]>
Link: https://lore.kernel.org/all/[email protected]
Signed-off-by: Dario Binacchi <[email protected]>
|
|
Switch to using bootstd. Note with this change, we will stop using
distro_bootcmd and instead depend entirely on bootflow method of
starting the system up.
Drop header files that are no longer needed in am64x_evm.h.
k3_dfu.h is available via k3_dfu.env in am64x.env.
Drop unused macro CFG_SYS_SDRAM_BASE1.
Signed-off-by: Roger Quadros <[email protected]>
Reviewed-by: Nishanth Menon <[email protected]>
|
|
The boot option automatically created by efibootmgr is identified
by the special guid appended in the optional data of boot option.
The same mechanism is implemented in the EDK II reference
implementation, it uses the different guid from the one currently
U-Boot uses.
The guid indicating auto-created boot option is not defined in the
UEFI specification, but some userspace tools such as 'efivar' package
are aware of the guid used in EDK II as auto-created boot option.
So let's use the same guid as EDK II reference implementation.
Signed-off-by: Masahisa Kojima <[email protected]>
Reviewed-by: Heinrich Schuchardt <[email protected]>
|
|
Provide test coverage for the new expo object type, including building
and reading/writing settings.
Signed-off-by: Simon Glass <[email protected]>
|
|
At present cedit only supports menu keys. For textline objects we need
to insert normal ASCII characters.
We also need to handle backspace, which is ASCII 9.
In fact, expo does not make use of all the menu keys, so partition
them accordingly and update the logic to support normal ASCII
characters, too.
Signed-off-by: Simon Glass <[email protected]>
|
|
A textline is a line of text which can be edited by the user. It has a
maximum length (in chracters) but otherwise there are no restrictions.
Signed-off-by: Simon Glass <[email protected]>
|
|
Add the CLI state, a buffer to hold the old value of the text being
edited and a place to save vidconsole entry context. These will be use
by the textline object.
Set an upper limit on the maximum number of characters in a textline
object supported by expo, at least for now.
Signed-off-by: Simon Glass <[email protected]>
|
|
So far only menus can be highlighted. With the coming addition of
text lines we need to be able to highlight other objects. Add a function
to determine whether an object can be highlighted.
Signed-off-by: Simon Glass <[email protected]>
|
|
This internal function could use a comment. Add one.
Also tidy up a few other comments.
Signed-off-by: Simon Glass <[email protected]>
fixup: comments
|
|
Add rudimentary support for displaying a cursor on a vidconsole. This
helps the user to see where text is being entered.
The implementation so far is very simple: the cursor is just a vertical
bar of fixed width and cannot be erased. To erase the cursor, the text
must be redrawn over it.
This is good enough for expo but will need enhancement to be useful for
the command-line console. For example, it could save and restore the
area behind the cursor.
For now, enable this only for expo, to reduce code size.
Signed-off-by: Simon Glass <[email protected]>
|
|
At present this is called only when a newline is detected, since this
indicates the start of a line of text being entered.
Export this function so it can be used by expo, which may start a new
text line itself, without first writing out a newline.
Signed-off-by: Simon Glass <[email protected]>
|
|
Text entry operates within a context which includes quite a bit of
information. For example, with Truetype fonts, each character in the
text string has a position stored, so that it is possible to
backspace to that character. This information is built up as strings
are drawn on the display.
For the command line, there is just a single context. It is created
when command-line entry starts and it is destroyed (or at least not
needed anymore) when the user presses <enter> to enter the command.
By contrast, expo needs to be able to switch in and out of a text-entry
context, since it is also displaying other objects in the scene.
Add a way to save and restore the entry context for a vidconsole. This
is only needed for the truetype vidconsole, so add a method for that,
storing the information in an abuf struct.
Signed-off-by: Simon Glass <[email protected]>
|
|
At present there is a method for measuring text, but if the actual text
string is not known, it cannot be used.
For text editor we want to set the size of the entry box to cover the
expected text size. Add the concept of a 'norminal' size with a method
to calculate that for the vidconsole.
If the method is not implemented, fall back to using the font size,
which is sufficient for fixed-width fonts.
Signed-off-by: Simon Glass <[email protected]>
|
|
Create a init function so that it is easy to use command-line reading.
Signed-off-by: Simon Glass <[email protected]>
|
|
When inputting text outside the command line we don't want to use tab
for command completion. Add an option to control this.
Signed-off-by: Simon Glass <[email protected]>
|
|
When inputting text outside the command line we don't want history to be
accessible. Add an option to control this.
Signed-off-by: Simon Glass <[email protected]>
|
|
Move most of the inner loop from cread_line() into a new function. This
will allow using it from other code.
This involves adding a few more members to the state struct.
Signed-off-by: Simon Glass <[email protected]>
|
|
We want to reuse the editing code elsewhere. As a first step, move the
common variables into a struct. This will allow us to eventually put the
contents of the inner loop in a function, so it can be called from
elsewhere.
Signed-off-by: Simon Glass <[email protected]>
|
|
Use a static inline and adjust the logic to avoid the need for #ifdefs in
cli_readline_into_buffer()
Signed-off-by: Simon Glass <[email protected]>
|
|
There is a function for this but it is never used. Showing the history is
a useful feature, so add a new 'history' command.
Signed-off-by: Simon Glass <[email protected]>
|
|
As the code to switch an ARM core from secure to the non-secure state
needs to know the base address of the Generic Interrupt Controller
(GIC), we read an Arm Cortex defined system register that is supposed to
hold that base address. However there are SoCs out there that get this
wrong, and this CBAR register either reads as 0 or points to the wrong
address. To accommodate those systems, so far we use a macro defined in
some platform specific header files, for affected boards.
To simplify future extensions, replace that macro with a Kconfig variable
that holds this override address, and define a default value for SoCs
that need it.
Signed-off-by: Andre Przywara <[email protected]>
Reviewed-by: Sam Edwards <[email protected]>
|
|
Fix up remaining occurances of EVENT_SPY with no suffix.
Fixes: 6c4cad7438 ("event: Rename EVENT_SPY to EVENT_SPY_FULL")
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Added new xenguest_arm64_virtio_defconfig which
enables support for virtio-blk using various types
of transport like virtio-pci, vrtio-mmio. Currently
supported: up to 2 PCI host bridges and 10 MMIO devices.
Note: DT parsing code was partly taken from pci-uclass.c
Limitation: All memory regions should be
below 4GB address space.
Signed-off-by: Andrii Chepurnyi <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-fsl-qoriq
Drop legacy PPA secure FW support
support for MC reserved memory
reset the FLSHxCR1 registers for nxp_fspi
|
|
blk_{read,write}_devnum() are no longer used by anywhere in the
source tree. Drop them.
Signed-off-by: Bin Meng <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
get_desc() can be useful outside blk-uclass.c. Let's change it to
an API and make it externally visible.
Signed-off-by: Bin Meng <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Allow optionally set the logical block size of the host device to
bind in the "host bind" command. If not given, defaults to 512.
Signed-off-by: Bin Meng <[email protected]>
|
|
Avoid using the magic number 512 directly.
Signed-off-by: Bin Meng <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Add support for declaring in device tree the reserved memory ranges
required for MC. Since the MC firmware acts as any DMA master present
in the SoC, the reserved memory ranges need also be identity mapped
in the SMMU, so create the required 'iommu-addresses' property in
the reserved memory nodes.
For now this support is used only on LX2160A SoCs.
Signed-off-by: Laurentiu Tudor <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
|
|
PPA was a secure firmware developed in-house which is no longer
supported and replaced by TF-A quite some years ago. Drop support
for it.
Signed-off-by: Laurentiu Tudor <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
|
|
When copying the name of a stdio device we must ensure that it is NUL
terminated before passing it to strcmp() to avoid a buffer overrun.
Truncating the name field leads to failure to deregister a stdio device.
When copying we must ensure that the name field sizes match.
Addresses-Coverity-ID: 350462 String not null terminated
Fixes: 5294e97832a6 ("stdio: extend "name" to 32 symbols")
Signed-off-by: Heinrich Schuchardt <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
spl_invoke_atf function will not be returned to SPL. Thus, we need to
set __noreturn function attribute to the function.
Signed-off-by: Chanho Park <[email protected]>
|
|
For Xilinx ZynqMP SOC new parameter was added and now it can
set 7 parameters for its pins. Pinmux status command will
print the status of these parameters for each pin. But
current print buffer length is only 80 characters long, increase it
to 90 to print all the parameters without truncation.
Signed-off-by: Venkatesh Yadav Abbarapu <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michal Simek <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-rockchip
- Add Board: rk3568 Bananapi R2Pro;
- Update pcie bifurcation support;
- dwc_eth_qos controller support for rk3568 and rk3588;
- Compressed binary support for U-Boot on rockchip platform;
- dts and config updates for different board and soc;
[ trini: Fix conflict on include/spl.h ]
Signed-off-by: Tom Rini <[email protected]>
|
|
enable CONFIG_OF_LIBFDT_OVERLAY and use it on Radxa ROCK Pi S.
Signed-off-by: FUKAUMI Naoki <[email protected]>
|
|
all rk3308 boards should use their own dtb file.
also, change fdt_addr_r to avoid following error:
"ERROR: Did not find a cmdline Flattened Device Tree"
it happens on Radxa ROCK Pi S (256MB/512MB) with kernel built from
Radxa BSP.
Signed-off-by: FUKAUMI Naoki <[email protected]>
|
|
Sync the device tree for RK3588 series with Linux 6.6-rc1.
Signed-off-by: FUKAUMI Naoki <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
If LZMA Compression support is enabled, LZMA compressed U-Boot
binary will be placed at a specified RAM location which is
defined at CONFIG_SYS_LOAD_ADDR and will be assigned as the
source address.
image_decomp() function, will decompress the LZMA compressed
U-Boot binary which is placed at source address(CONFIG_SYS_LOAD_ADDR)
to the default CONFIG_SYS_TEXT_BASE location.
spl_load_fit_image function will load the decompressed U-Boot
binary, which is placed at the CONFIG_SYS_TEXT_BASE location.
Signed-off-by: Manoj Sai <[email protected]>
Signed-off-by: Suniel Mahesh <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
If GZIP Compression support is enabled, GZIP compressed U-Boot binary
will be at a specified RAM location which is defined at
CONFIG_SYS_LOAD_ADDR and will be assign it as the source address.
gunzip function in spl_load_fit_image ,will decompress the GZIP
compressed U-Boot binary which is placed at
source address(CONFIG_SYS_LOAD_ADDR) to the default
CONFIG_SYS_TEXT_BASE location.
spl_load_fit_image function will load the decompressed U-Boot
binary, which is placed at the CONFIG_SYS_TEXT_BASE location.
Signed-off-by: Manoj Sai <[email protected]>
Signed-off-by: Suniel Mahesh <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
With the commit 4fcba5d556b4 ("regulator: implement basic reference
counter"), keeping regulator enablement in balance become more important.
Calling regulator_autoset multiple times on a fixed regulator increase
the enable count for each call, resulting in an unbalanced enable count.
Introduce a AUTOSET_DONE flag and use it to mark that autoset has run
for the regulator. Return -EALREADY on any subsequent call to autoset.
This fixes so that the enable count is only ever increased by one per
regulator for autoset.
Fixes: 4fcba5d556b4 ("regulator: implement basic reference counter")
Signed-off-by: Jonas Karlman <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
The PCI helpers read only the base address for a PCI region. In some cases
the size is needed as well, e.g. to pass along to a driver which needs to
know the size of its register area.
Update the functions to allow the size to be returned. For serial, record
the information and provided it with the serial_info() call.
A limitation still exists in that the size is not available when OF_LIVE
is enabled, so take account of that in the tests.
Signed-off-by: Simon Glass <[email protected]>
|
|
This function cannot return true if PCI is not enabled, since no PCI
devices will have been bound. Add a check for this to reduce code size
where it is used.
Signed-off-by: Simon Glass <[email protected]>
|
|
The spl_phase() function indicates whether U-Boot is in SPL and before
or after relocation. But sometimes it is useful to check for SPL with
zero code-size impact. Since spl_phase() checks the global_data flags,
it does add a few bytes.
Add a new spl_in_proper() function to check if U-Boot proper is
running, regardless of the relocation status.
Signed-off-by: Simon Glass <[email protected]>
|
|
This uses ARRAY_SIZE() but does not include the header file which declares
it. Fix this, so that command.h can be included without common.h
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Mattijs Korpershoek <[email protected]>
|
|
Typically the bloblist is set up after the devicetree is present. This
makes sense because bloblist may use malloc() to allocate the space it
needs.
However sometimes the devicetree itself may be present in the bloblist.
In that case it is at a known location in memory so we can init the
bloblist very early, before devicetree.
Add a flag to indicate whether the bloblist has been inited. Add a
function to init it only if needed. Use that in the init sequence.
Signed-off-by: Simon Glass <[email protected]>
|
|
Add support for writing a single 64-bit value into a property.
Repurpose the existing tests to handle this case too.
Signed-off-by: Simon Glass <[email protected]>
|
|
Add functions to write a boolean property. This involves deleting it if
the value is false.
Add a new ofnode_has_property() as well. Add a comment about the behaviour
of of_read_property() when the property value is empty.
Signed-off-by: Simon Glass <[email protected]>
|
