| Age | Commit message (Collapse) | Author |
|---|
|
Some boards still don't enable BLK but we want to be able to at least
compile the code which relies on this. For example, bootstd includes
calls to blk_...() functions, albeit with a check for BLK so that the
code is eliminated by the compiler.
Reduce the scope of the BLK #ifdef to help with this.
Signed-off-by: Simon Glass <[email protected]>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/22796
- Switch to using upstream DT on DH i.MX8MP DHCOM PDK2/PDK3.
- Add ability to build fallback DTBOs from arch/$(ARCH)/dts.
- Remove fdt_high and initrd_high env variables from imx6-dhcom.
- Add dummy clk for imx8.
- Fix DT corruption in imx8_cpu.
- Improve DDR stability on pico-imx7d.
|
|
Remove both "fdt_high" and "initrd_high" environment variables
in favor of "bootm_size" to safely contain a kernel, device tree
and initrd for relocation inside of 256 MiB region of DRAM.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
Move do_irqinfo() prototype to a header file, otherwise compiler is not
happy:
arch/x86/lib/interrupts.c:130:5: warning: no previous prototype for ‘do_irqinfo’ [-Wmissing-prototypes]
Signed-off-by: Andy Shevchenko <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
[trini: Add 'struct cmd_tbl;' to irq_func.h]
Signed-off-by: Tom Rini <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-stm
CI: https://source.denx.de/u-boot/custodians/u-boot-stm/-/pipelines/22732
- stm32mp: fix boot issue with OP-TEE
- stm32mp: Add script to install U-Boot from SD/eMMC to SPI NOR on DH STM32MP15xx
- stm32mp: Switch to using upstream DT on DH STM32 DHSOM
- stm32mp: Generate u-boot.itb using binman on DH STM32 DHSOM
|
|
|
|
This adds TCPM framework in preparation for fusb302 support, which can
handle USB power delivery messages. This is needed to solve issues with
devices, that are running from a USB-C port supporting USB-PD, but not
having a battery.
Such a device currently boots to the kernel without interacting with
the power-supply at all. If there are no USB-PD message replies within
5 seconds, the power-supply assumes the peripheral is not capable of
USB-PD. It usually takes more than 5 seconds for the system to reach
the kernel and probe the I2C based fusb302 chip driver. Thus the
system always runs into this state. The power-supply's solution to
fix this error state is a hard reset, which involves removing the
power from VBUS. Boards without a battery (or huge capacitors) will
reset at this point resulting in a boot loop.
This imports the TCPM framework from the kernel. The porting has
originally been done by Rockchip using hardware timers and the Linux
kernel's TCPM code from some years ago.
I had a look at upgrading to the latest TCPM kernel code, but that
beast became a lot more complex due to adding more USB-C features.
I believe these features are not needed in U-Boot and with multiple
kthreads and hrtimers being involved it is non-trivial to port them.
Instead I worked on stripping down features from the Rockchip port
to an even more basic level. Also the TCPM code has been reworked
to avoid complete use of any timers (Rockchip used SoC specific
hardware timers + IRQ to implement delayed work mechanism). Instead
the delayed state changes are handled directly from the poll loop.
Note, that (in contrast to the original Rockchip port) the state
machine has the same hard reset quirk, that the kernel has - i.e.
it avoids disabling the CC pin resistors for devices that are not
self-powered. Without that quirk, the Radxa Rock 5B will not just
end up doing a machine reset when a hard reset is triggered, but will
not even recover, because the CPU will loose power and the FUSB302
will keep this state because of leak voltage arriving through the RX
serial pin (assuming a serial adapter is connected).
This also includes a 'tcpm' command, which can be used to get
information about the current state and the negotiated voltage
and current.
Co-developed-by: Wang Jie <[email protected]>
Signed-off-by: Wang Jie <[email protected]>
Tested-by: Soeren Moch <[email protected]>
Tested-by: Anand Moon <[email protected]>
Reviewed-by: Jonas Karlman <[email protected]>
Signed-off-by: Sebastian Reichel <[email protected]>
|
|
Rasmus Villemoes <[email protected]> says:
Some small improvements to the serial rx buffer feature.
CI seems happy: https://github.com/u-boot/u-boot/pull/674
Link: https://lore.kernel.org/r/[email protected]
|
|
The initialization of upriv->buf doesn't check for a NULL return. But
there's actually no point in doing a separate, unconditional malloc()
in post_probe; we can just make serial_dev_priv contain the rx buffer
itself, and let the (larger) allocation be handled by the driver core
when it allocates the ->per_device_auto. The total run-time memory
used is mostly the same, we reduce the code size a little, and as a
bonus, struct serial_dev_priv does not contain the unused members when
!SERIAL_RX_BUFFER.
Signed-off-by: Rasmus Villemoes <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
The current implementation of the circular rx buffer falls into a
common trap with circular buffers: It keeps the head/tail indices
reduced modulo the buffer size. The problem with that is that it makes
it impossible to distinguish "buffer full" from "buffer empty",
because in both situations one has head==tail.
This can easily be demonstrated: Build sandbox with RX_BUFFER enabled,
set the RX_BUFFER_SIZE to 32, and try pasting the string
01234567890123456789012345678901
Nothing seems to happen, but in reality, all characters have been read
and put into the buffer, but then tstc ends up believing nothing is in
the buffer anyway because upriv->rd_ptr == upriv->wr_ptr.
A better approach is to let the indices be free-running, and only
reduce them modulo the buffer size when accessing the array. Then
"empty" is head-tail==0 and "full" is head-tail==size. This does rely
on the buffer size being a power-of-two and the free-running
indices simply wrapping around to 0 when incremented beyond the
maximal positive value.
Incidentally, that change from signed to unsigned int also improves
code generation quite a bit: In C, (signed int)%(signed int) is
defined to have the sign of the dividend (so (-35) % 32 is -3, not
29), and hence despite the modulus being a power-of-two, x % 32 does
not actually compile to the same as a simple x & 31 - on x86 with -Os,
it seems that gcc ends up emitting an idiv instruction, which is quite
expensive.
Signed-off-by: Rasmus Villemoes <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
This is cosmetic change.
Remove the empty comment blocks remaining after conversion to Kconfig
of CONFIG_SYS_MAX_NAND_DEVICE and CONFIG_SERVERIP.
Signed-off-by: Patrick Delaunay <[email protected]>
|
|
STM32MP15xx DHSOM
Make the dh_update_sd_to_sf script generic, rename it to dh_update_block_to_sf
and implement two specific dh_update_sd_to_sf and dh_update_emmc_to_sf scripts
which load U-Boot from either SD or eMMC and install it into SPI NOR.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
|
|
Add support for the wget command with NET_LWIP. The command normally
expects a URL: wget [loadaddr] url, but it also accepts the legacy
syntax: wget [loadaddr] [server:]file.
The server IP may alternatively be supplied via ${httpserverip} which
has higher priority than ${serverip}.
Based on code initially developed by Maxim U.
Signed-off-by: Jerome Forissier <[email protected]>
Co-developed-by: Maxim Uvarov <[email protected]>
Cc: Maxim Uvarov <[email protected]>
Signed-off-by: Jerome Forissier <[email protected]>
Acked-by: Ilias Apalodimas <[email protected]>
|
|
Add CMD_DNS when NET_LWIP is enabled to provide the dns command using
lwIP.
Signed-off-by: Jerome Forissier <[email protected]>
Acked-by: Ilias Apalodimas <[email protected]>
|
|
Add support for the the ping command with NET_LWIP. The implementation
is derived from lwIP's contrib/apps/ping/ping.c.
Signed-off-by: Jerome Forissier <[email protected]>
Acked-by: Ilias Apalodimas <[email protected]>
|
|
Implement do_tftpb(). This implementation of the tftp command
supports an optional port number. For example:
tftp 192.168.0.30:9069:file.bin
It also supports taking the server IP from ${tftpserverip} if
defined, before falling back to ${serverip}.
Signed-off-by: Jerome Forissier <[email protected]>
Acked-by: Ilias Apalodimas <[email protected]>
Tested-by: Ilias Apalodimas <[email protected]>
|
|
Add what it takes to enable NETDEVICES with NET_LWIP and enable DHCP as
well as the dhcp command. CMD_TFTPBOOT is selected by BOOTMETH_EFI due
to this code having an implicit dependency on do_tftpb().
Note that PXE is likely non-fonctional with NET_LWIP (or at least not
100% functional) because DHCP option 209 is not supported by the lwIP
library. Therefore, BOOTP_PXE_DHCP_OPTION cannot be enabled.
Signed-off-by: Jerome Forissier <[email protected]>
Tested-by: Ilias Apalodimas <[email protected]>
Acked-by: Ilias Apalodimas <[email protected]>
|
|
Add a function to start a given network device, and update eth_init()
to use it.
Signed-off-by: Jerome Forissier <[email protected]>
Reviewed-by: Ilias Apalodimas <[email protected]>
|
|
Make net.h a wrapper which includes net-common.h and either
net-legacy.h or net-lwip.h based on NET_LWIP. The function
copy_filename() can be useful when NET_LWIP is enabled, therefore
move it out of net/net.c which is built only when networking choice
is NET and create a new file net/net-common.c.
Signed-off-by: Jerome Forissier <[email protected]>
Acked-by: Ilias Apalodimas <[email protected]>
|
|
|
|
The variable overlap_only_ram is used to specify that the new memory
region that is being created needs to come from the free memory pool
-- this is done by carving out the memory region from the free
memory. The name is a bit confusing though, as other allocated memory
regions, like boot-services code and data are also part of the RAM
memory. Rename the variable to overlap_conventional to highlight the
fact that it is the free/conventional memory that is being referred to
in this context.
Signed-off-by: Sughosh Ganu <[email protected]>
Reviewed-by: Ilias Apalodimas <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
The EFI_CONVENTIONAL_MEMORY type, which is the usable RAM memory is
now being managed by the LMB module. Remove the addition of this
memory type to the EFI memory map. This memory now gets added to the
EFI memory map as part of the LMB memory map update event handler.
Signed-off-by: Sughosh Ganu <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Ilias Apalodimas <[email protected]>
|
|
Some architectures have special or unique aspects which need
consideration when adding memory ranges to the list of available
memory map. Enable this config in such scenarios which allow
architectures and boards to define their own memory map.
Signed-off-by: Sughosh Ganu <[email protected]>
|
|
In U-Boot, LMB and EFI are two primary modules who provide memory
allocation and reservation API's. Both these modules operate with the
same regions of memory for allocations. Use the LMB memory map update
event to notify other interested listeners about a change in it's
memory map. This can then be used by the other module to keep track of
available and used memory.
There is no need to send these notifications when the LMB module is
being unit-tested. Add a flag to the lmb structure to indicate if the
memory map is being used for tests, and suppress sending any
notifications when running these unit tests.
Signed-off-by: Sughosh Ganu <[email protected]>
|
|
Add a flag LMB_NONOTIFY that can be passed to the LMB API's for
reserving memory. This will then result in no notification being sent
from the LMB module for the changes to the LMB's memory map.
While here, also add a description of the memory attributes that the
flags signify.
Signed-off-by: Sughosh Ganu <[email protected]>
|
|
The LMB module is to be used as a backend for allocating and freeing
up memory requested from other modules like EFI. These memory requests
are different from the typical LMB reservations in that memory
required by the EFI module cannot be overwritten, or re-requested. Add
versions of the LMB API functions with flags for allocating and
freeing up memory. The caller can then use these API's for specifying
the type of memory that is required. For now, these functions will be
used by the EFI memory module.
Signed-off-by: Sughosh Ganu <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
This series from Martyn Welch <[email protected]> adds the
ability to have a "fallback" option in extlinux.conf parsing, which can
be in turn used in A/B style update mechanisms.
Link: https://lore.kernel.org/u-boot/[email protected]/
|
|
We have previously added logic to allow a "fallback" option to be
specified in the extlinux configuration. Provide a command that allows
us to set this as the preferred default option when booting.
Combined with the bootcount functionality, this allows the "altbootcmd"
to provide a means of falling back to a previously known good state
after a failed update. For example, if "bootcmd" is set to:
bootflow scan -lb
We would set "altbootcmd" to:
bootmeth set extlinux fallback 1; bootflow scan -lb
Causing the boot process to boot from the fallback option.
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Martyn Welch <[email protected]>
|
|
The "fallback" extlinux config option allows us to set an alternative
default boot option for when it has been detected that the default is
failing. Implement the logic required to boot from this option when
desired.
Signed-off-by: Martyn Welch <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
When configured correctly, we can detect when boot fails after the boot
process has been handed over to the kernel through the use of U-Boot's
bootcount support. In some instances, such as when we are performing
atomic updates via a system such as OSTree, it is desirable to provide a
fallback option so that we can return to a previous (hopefully working)
state.
Add a "fallback" option to the supported extlinux configuration options
that points to a label like "default" so that we can utilise this in
later commits.
Signed-off-by: Martyn Welch <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Some flashes like the Infineon SEMPER NOR flash family use ECC. Under
this ECC scheme, multi-pass writes to an ECC block is not allowed.
In other words, once data is programmed to an ECC block, it can't be
programmed again without erasing it first.
Upper layers like file systems need to be given this information so they
do not cause error conditions on the flash by attempting multi-pass
programming. This can be done by setting 'writesize' in 'struct
mtd_info'.
Set the default to 1 but allow flashes to modify it in fixup hooks. If
more flashes show up with this constraint in the future it might be
worth it to add it to 'struct flash_info', but for now increasing its
size is not worth it.
This patch replicates the following upstream linux commit:
afd473e85827 ("mtd: spi-nor: core: Allow flashes to specify MTD writesize")
Acked-by: Tudor Ambarus <[email protected]>
Signed-off-by: Takahiro Kuwano <[email protected]>
|
|
Raymond Mao <[email protected]> says:
Integrate MbedTLS v3.6 LTS (currently v3.6.0) with U-Boot.
Motivations:
------------
1. MbedTLS is well maintained with LTS versions.
2. LWIP is integrated with MbedTLS and easily to enable HTTPS.
3. MbedTLS recently switched license back to GPLv2.
Prerequisite:
-------------
This patch series requires mbedtls git repo to be added as a
subtree to the main U-Boot repo via:
$ git subtree add --prefix lib/mbedtls/external/mbedtls \
https://github.com/Mbed-TLS/mbedtls.git \
v3.6.0 --squash
Moreover, due to the Windows-style files from mbedtls git repo,
we need to convert the CRLF endings to LF and do a commit manually:
$ git add --renormalize .
$ git commit
New Kconfig options:
--------------------
`MBEDTLS_LIB` is for MbedTLS general switch.
`MBEDTLS_LIB_CRYPTO` is for replacing original digest and crypto libs with
MbedTLS.
`MBEDTLS_LIB_CRYPTO_ALT` is for using original U-Boot crypto libs as
MbedTLS crypto alternatives.
`MBEDTLS_LIB_X509` is for replacing original X509, PKCS7, MSCode, ASN1,
and Pubkey parser with MbedTLS.
By default `MBEDTLS_LIB_CRYPTO_ALT` and `MBEDTLS_LIB_X509` are selected
when `MBEDTLS_LIB` is enabled.
`LEGACY_CRYPTO` is introduced as a main switch for legacy crypto library.
`LEGACY_CRYPTO_BASIC` is for the basic crypto functionalities and
`LEGACY_CRYPTO_CERT` is for the certificate related functionalities.
For each of the algorithm, a pair of `<alg>_LEGACY` and `<alg>_MBEDTLS`
Kconfig options are introduced. Meanwhile, `SPL_` Kconfig options are
introduced.
In this patch set, MBEDTLS_LIB, MBEDTLS_LIB_CRYPTO and MBEDTLS_LIB_X509
are by default enabled in qemu_arm64_defconfig and sandbox_defconfig
for testing purpose.
Patches for external MbedTLS project:
-------------------------------------
Since U-Boot uses Microsoft Authentication Code to verify PE/COFFs
executables which is not supported by MbedTLS at the moment,
addtional patches for MbedTLS are created to adapt with the EFI loader:
1. Decoding of Microsoft Authentication Code.
2. Decoding of PKCS#9 Authenticate Attributes.
3. Extending MbedTLS PKCS#7 lib to support multiple signer's certificates.
4. MbedTLS native test suites for PKCS#7 signer's info.
All above 4 patches (tagged with `mbedtls/external`) are submitted to
MbedTLS project and being reviewed, eventually they should be part of
MbedTLS LTS release.
But before that, please merge them into U-Boot, otherwise the building
will be broken when MBEDTLS_LIB_X509 is enabled.
See below PR link for the reference:
https://github.com/Mbed-TLS/mbedtls/pull/9001
Miscellaneous:
--------------
Optimized MbedTLS library size by tailoring the config file
and disabling all unnecessary features for EFI loader.
From v2, original libs (rsa, asn1_decoder, rsa_helper, md5, sha1, sha256,
sha512) are completely replaced when MbedTLS is enabled.
From v3, the size-growth is slightly reduced by refactoring Hash functions.
From v6, smaller implementations for SHA256 and SHA512 are enabled and
target size reduce significantly.
Target(QEMU arm64) size-growth when enabling MbedTLS:
v1: 6.03%
v2: 4.66%
v3 - v5: 4.55%
v6: 2.90%
Tests done:
-----------
EFI Secure Boot test (EFI variables loading and verifying, EFI signed image
verifying and booting) via U-Boot console.
EFI Secure Boot and Capsule sandbox test passed.
Known issues:
-------------
None.
Link: https://lore.kernel.org/u-boot/[email protected]/
|
|
Previous patch has introduced MbedTLS porting layer for mscode parser,
here to adjust the header and makefiles accordingly.
Adding _LEGACY Kconfig for legacy mscode implementation.
Signed-off-by: Raymond Mao <[email protected]>
|
|
Previous patch has introduced MbedTLS porting layer for PKCS7 parser,
here to adjust the header and makefiles accordingly.
Signed-off-by: Raymond Mao <[email protected]>
|
|
Previous patch has introduced MbedTLS porting layer for x509 cert parser,
here to adjust the header and makefiles accordingly.
Signed-off-by: Raymond Mao <[email protected]>
|
|
Previous patch has introduced MbedTLS porting layer for public key,
here to adjust the header and makefiles accordingly.
Signed-off-by: Raymond Mao <[email protected]>
Reviewed-by: Ilias Apalodimas <[email protected]>
|
|
Implement digest shim layer on top of MbedTLS crypto library.
Introduce <alg>_MBEDTLS kconfig for MbedTLS crypto implementations.
Signed-off-by: Raymond Mao <[email protected]>
|
|
We don't need an API specially for non-watchdog since sha1_csum_wd
supports it by disabling CONFIG_HW_WATCHDOG and CONFIG_WATCHDOG.
Set 0x10000 as default chunk size for SHA1.
Signed-off-by: Raymond Mao <[email protected]>
Reviewed-by: Ilias Apalodimas <[email protected]>
|
|
We don't need an API specially for non-watchdog since md5_wd supports
it by disabling CONFIG_HW_WATCHDOG and CONFIG_WATCHDOG.
Set 0x10000 as default chunk size for MD5.
Signed-off-by: Raymond Mao <[email protected]>
Reviewed-by: Ilias Apalodimas <[email protected]>
Reviewed-by: Michal Simek <[email protected]>
|
|
Adapt digest header files to support both original libs and MbedTLS
by switching on/off MBEDTLS_LIB_CRYPTO.
Introduce <alg>_LEGACY kconfig for legacy hash implementations.
sha256.o should depend on SHA256 kconfig only but not SUPPORT_EMMC_RPMB,
SHA256 should be selected when SUPPORT_EMMC_RPMB is enabled instead.
`IS_ENABLED` or `CONFIG_IS_ENABLED` is not applicable here, since
including <linux/kconfig.h> causes undefined reference on schedule()
with sandbox build, as <linux/kconfig.h> includes <generated/autoconf.h>
which enables `CONFIG_HW_WATCHDOG` and `CONFIG_WATCHDOG` but no schedule()
are defined in sandbox build,
Thus we use `#if defined(CONFIG_MBEDTLS_LIB_CRYPTO)` instead.
Signed-off-by: Raymond Mao <[email protected]>
Reviewed-by: Ilias Apalodimas <[email protected]>
|
|
Port mbedtls with adapted libc header files.
Add mbedtls default config header file.
Optimize mbedtls default config by disabling unused features to
reduce the target size.
Add mbedtls kbuild makefile.
Add Kconfig skeleton and config submenu entry for selecting
crypto libraries between mbedtls and legacy ones.
Add the mbedtls include directories into the build system.
Port u-boot hash functions as MbedTLS crypto alternatives and set
it as default.
Subsequent patches will separate those Kconfigs into pairs of
_LEGACY and _MBEDTLS for controlling the implementations of legacy
crypto libraries and MbedTLS ones respectively.
The motivation of moving and adapting *INT* macros from kernel.h
to limits.h is to fulfill the MbedTLS building requirement.
The conditional compilation statements in MbedTLS expects the
*INT* macros as constant expressions, thus expressions like
`((int)(~0U >> 1))` will not work.
Prerequisite
------------
This patch series requires mbedtls git repo to be added as a
subtree to the main U-Boot repo via:
$ git subtree add --prefix lib/mbedtls/external/mbedtls \
https://github.com/Mbed-TLS/mbedtls.git \
v3.6.0 --squash
Moreover, due to the Windows-style files from mbedtls git repo,
we need to convert the CRLF endings to LF and do a commit manually:
$ git add --renormalize .
$ git commit
Signed-off-by: Raymond Mao <[email protected]>
|
|
Right now xhci header file defines XHCI_MAX_HALT_USEC macro
twice. Fix the same.
Cc: Bin Meng <[email protected]>
Signed-off-by: Bhupesh Sharma <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-amlogic
- Add Libre Computer boards into proper libre-computer board directory
- Add new Boards:
- Libre Computer aml-s905d3-cc
- Libre Computer aml-a311d-cc
- Add capsule update to libretech-ac and the new boards since they have an onboard SPI nor flash
- Fix HDMI support after sync to v6.11 and regulator enable from Marek
- Fix khadas-vim3 android config for android-mainline kernel
- Disable meson64 boot targets when configs are not eavailable
|
|
When populating BOOT_TARGET_DEVICES on Amlogic Meson platforms, verify
that the shell commands for accessing the relevant media have been
enabled in the build configuration.
This was already being done for USB, NVME and SCSI devices, but not
for MMC devices or network boot. This meant that configuring U-Boot
without the networking or MMC subsystems/drivers would cause an error
to be thrown during preprocessing.
Signed-off-by: Callum Parsey <[email protected]>
Reviewed-by: Neil Armstrong <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Neil Armstrong <[email protected]>
|
|
The device tree overlays are not part of the
Android Common Kernel code [1]
Historically, they existed to enable some Android specific
features but they have been removed.
Remove the dtbos logic since these files do no longer exist.
[1] https://android.googlesource.com/kernel/common/+/ac2ea0bb91a3b5f5e71eba66c441e58beca6767e/arch/arm64/boot/dts/amlogic/
Signed-off-by: Mattijs Korpershoek <[email protected]>
Reviewed-by: Guillaume La Roque <[email protected]>
Reviewed-by: Neil Armstrong <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Neil Armstrong <[email protected]>
|
|
The Android Common Kernel is over 34MiB now [1]. This does not
include any kernel modules nor the Android ramdisk.
To make sure we are future proof, increase both recovery
and boot partitions to 64 MiB.
[1] https://source.android.com/docs/core/architecture/kernel/gki-android15-6_6-release-builds
Signed-off-by: Mattijs Korpershoek <[email protected]>
Reviewed-by: Guillaume La Roque <[email protected]>
Reviewed-by: Neil Armstrong <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Neil Armstrong <[email protected]>
|
|
This switches all boards with the Allwinner H616/H618/H313/H700 SoCs over to
use OF_UPSTREAM. We are doing it for this SoC family only since the DTs
between the U-Boot and the kernel repo are exactly identical, whereas other
families have one compatibility fix in U-Boot to allow booting older kernels.
Other will follow if this plays out well.
The biggest chunk otherwise is adding support for an Anbernic game console,
using the H700 SoC. For that we need to enhance the DRAM support code, and
pick two DT commits from the mainline kernel/DT rebasing repo, followed
by the defconfig patch.
On top of that two small fixes for the old Allwinner A80.
Gitlab CI passed, and I booted that briefly on some boards, including an
H616 and an H618 one (with LPDDR4).
|
|
Assorted Tegra enhancements. Merged with the recent XPL_BUILD changes,
resolve some whitespace issues and fix the name of the new apalis-tk1
env file by Tom.
Signed-off-by: Tom Rini <[email protected]>
|
|
In some cases access to GPIOs is needed so early that DM
is not ready even nearly. These functions are exactly for
this case.
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
|
Convert boards to use text based env. This is the first stage of
conversion, common inclusions should be converted next.
Acked-by: Francesco Dolcini <[email protected]> # Toradex Apalis TK1
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Svyatoslav Ryhel <[email protected]>
|
