| Age | Commit message (Collapse) | Author |
|---|
|
https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.07-rc4
zynqmp:
- Fix DP PLL configuration for zcu102/zcu106 and SOM
- Fix split mode for starting R5s
- DT fixes
- Remove firmware node for mini configurations
- Wire TEE for multi DTB fit image
xilinx:
- Handle board_get_usable_ram_top(0) properly
phy:
- Extend psgtr timeout
mmc:
- Fix mini configuration which misses zynqmp_pm_is_function_supported()
|
|
The bulk of it is (finally!) some DT sync from the kernel. We refrained
from syncing one incompatible change, as this would spoil booting Linux
kernels before v5.13 with U-Boot's DT (via UEFI, for instance).
I test booted Linux v5.18 and v5.4 with that new DT on some boards, and
the headless peripherals (MMC, USB, Ethernet) seemed to work.
The rest are fixes:
- silencing missing clock warnings due to the new pinctrl driver
- fixing "UART0 on PortF", allowing UART access through the SD card pins
- add an F1C100s clock driver, to enable MMC support (SPI comes later)
- some cleanups for CONS_INDEX_n in Kconfig
Tested on BananaPi-M1, Pine64-LTS, Pine-H64, X96-Mate (H616) and
OrangePi-Zero.
|
|
Some devices enumerate various clocks in their DT, and many drivers
just blanketly try to enable all of them. This creates problems
since we only model a few gate clocks, and the clock driver outputs
a warning when a clock is not described:
=========
sunxi_set_gate: (CLK#3) unhandled
=========
Some clocks don't have an enable bit, or are already enabled in a
different way, so we might want to just ignore them.
Add a CCU_CLK_F_DUMMY_GATE flag that indicates that case, and define
a GATE_DUMMY macro that can be used in the clock description array.
Define a few clocks, used by some pinctrl devices, that way to suppress
the runtime warnings.
Signed-off-by: Andre Przywara <[email protected]>
Reviewed-by: Samuel Holland <[email protected]>
|
|
Use the de10-nano files as templates for the de10-standard board.
The files in qts directory are generated by quartus from the GHRD
design.
Signed-off-by: Humberto Naves <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
commit ffb0f6f488b9 ("treewide: Rename PHY_INTERFACE_MODE_NONE to
PHY_INTERFACE_MODE_NA") broke the phy_string_for_interface function.
Fix it.
Fixes ffb0f6f488b9 ("treewide: Rename PHY_INTERFACE_MODE_NONE to PHY_INTERFACE_MODE_NA")
Signed-off-by: Tim Harvey <[email protected]>
Cc: Marek Behún <[email protected]>
Cc: Stefan Roese <[email protected]>
Cc: Ramon Fried <[email protected]>
Cc: Vladimir Oltean <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
Reviewed-by: Marek Behún <[email protected]>
Reviewed-by: Ramon Fried <[email protected]>
|
|
Now, spi_flash_probe_bus_cs() relies on DT for spi speed and mode
and logically calls spi_get_bus_and_cs(). In case spi mode and speed are
not read from DT, make usage of spi_flash_probe() instead.
To sum-up:
- Previous call tree was:
spi_flash_probe() -> spi_flash_probe_bus_cs() -> spi_get_bus_and_cs()
- Current call tree is:
spi_flash_probe() -> _spi_get_bus_and_cs()
spi_flash_probe_bus_cs() -> spi_get_bus_and_cs()
This patch impacts the following :
- cmd/sf.c: if spi mode and/or speed is passed in argument of
do_spi_flash_probe(), call spi_flash_probe() otherwise call
spi_flash_probe_bus_cs().
- drivers/net/fm/fm.c: as by default spi speed and mode was set to
0 and a comment indicates that speed and mode are read from DT,
use spi_flash_probe_bus_cs().
- drivers/net/pfe_eth/pfe_firmware.c: spi speed and mode are not read
from DT by all platforms using this driver, so keep legacy and replace
spi_flash_probe_bus_cs() by spi_flash_probe();
- drivers/net/sni_netsec.c : spi speed and mode are not read from DT,
so replace spi_flash_probe_bus_cs() by spi_flash_probe().
- drivers/usb/gadget/max3420_udc.c: Can't find any platform which make
usage of this driver, nevertheless, keep legacy and replace
spi_get_bus_and_cs() by _spi_get_bus_and_cs().
- env/sf.c: a comment indicates that speed and mode are read
from DT. So use spi_flash_probe_bus_cs().
Signed-off-by: Patrice Chotard <[email protected]>
Cc: Marek Behun <[email protected]>
Cc: Jagan Teki <[email protected]>
Cc: Vignesh R <[email protected]>
Cc: Joe Hershberger <[email protected]>
Cc: Ramon Fried <[email protected]>
Cc: Lukasz Majewski <[email protected]>
Cc: Marek Vasut <[email protected]>
Cc: Wolfgang Denk <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Stefan Roese <[email protected]>
Cc: "Pali Rohár" <[email protected]>
Cc: Konstantin Porotchkin <[email protected]>
Cc: Igal Liberman <[email protected]>
Cc: Bin Meng <[email protected]>
Cc: Pratyush Yadav <[email protected]>
Cc: Sean Anderson <[email protected]>
Cc: Anji J <[email protected]>
Cc: Biwen Li <[email protected]>
Cc: Priyanka Jain <[email protected]>
Cc: Chaitanya Sakinam <[email protected]>
|
|
Move legacy spi_get_bus_and_cs() code to _spi_get_bus_and_cs().
Add new spi_get_bus_and_cs() implementation which rely on DT
for speed and mode and don't need any drv_name nor dev_name
parameters. This will prepare the ground for next patch.
Update all callers to use _spi_get_bus_and_cs() to keep the
same behavior.
Signed-off-by: Patrice Chotard <[email protected]>
Cc: Marek Behun <[email protected]>
Cc: Jagan Teki <[email protected]>
Cc: Vignesh R <[email protected]>
Cc: Joe Hershberger <[email protected]>
Cc: Ramon Fried <[email protected]>
Cc: Lukasz Majewski <[email protected]>
Cc: Marek Vasut <[email protected]>
Cc: Wolfgang Denk <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Stefan Roese <[email protected]>
Cc: "Pali Rohár" <[email protected]>
Cc: Konstantin Porotchkin <[email protected]>
Cc: Igal Liberman <[email protected]>
Cc: Bin Meng <[email protected]>
Cc: Pratyush Yadav <[email protected]>
Cc: Sean Anderson <[email protected]>
Cc: Anji J <[email protected]>
Cc: Biwen Li <[email protected]>
Cc: Priyanka Jain <[email protected]>
Cc: Chaitanya Sakinam <[email protected]>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
u-boot-imx-20220523
-------------------
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/12087
Additionally to u-boot-imx20200520:
- DH MX8MP
- i.MX GPIO: reading GPIO when direction is output
- Menlo i.MX53: switch to DM
And from u-boot-imx20200520:
- fix Verdin hang
- add pca9450 regulator
- conversion to DM_SERIAL
- NAND block handling
- fix crypto
- enable cache on some boards
- add ACC board (MX6)
|
|
Add support for DH electronics i.MX8M Plus DHCOM SoM on PDK2 carrier board.
Currently supported are serial console, EQoS and FEC ethernets, eMMC, SD,
SPI NOR and USB 3.0 host.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
|
|
Some devicetree updates make use of newly-exposed clocks and resets.
To support that, copy the binding headers from the Linux v5.18-rc1 tag.
Signed-off-by: Samuel Holland <[email protected]>
|
|
Use phy address from device tree instead of CONFIG_FEC_MXC_PHYADDR from
board header. This is required, because the DH picoITX and DRC02 boards
require different settings than PDK2. The corresponding 'phy-handle'
device tree properties are already there.
I tested this change on picoITX and DRC02, but on PDK2 it is untested.
Reviewed-by: Marek Vasut <[email protected]>
Signed-off-by: Philip Oberfichtner <[email protected]>
|
|
Add PCA9450 regulator driver. This is complementary driver for the BUCKn
and LDOn regulators provided by the PCA9450 PMIC driver. Currently the
driver permits reading the settngs and configuring the BUCKn and LDOn
regulators.
Reviewed-by: Fabio Estevam <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
|
|
Enable CONFIG_DM_SERIAL. uart2 and its pinmux was already
marked with u-boot,dm-spl.
Signed-off-by: Peng Fan <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
The Bosch ACC (Air Center Control) Board is based on the i.MX6D.
The device tree is copied from Linux, see [1]. The only difference
compared to the Linux DT is the removal of usbphynop properties. They are
defined in the Linux version of imx6qdl.dtsi, but not in the u-boot
version.
[1] Commit 6192cf8ac082 from
git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux.git
Signed-off-by: Philip Oberfichtner <[email protected]>
|
|
When the device tree indicates support for role switching through
the "usb-role-switch" property, take the "role-switch-default-mode"
property into account when deciding which role to put the
controller into.
This makes USB devices work on Apple M1 systems where the device
tree may include a "dr_mode" property that is set to "otg", but
where we need to put the controller into "host" mode to see
devices connected to the type-C ports.
Signed-off-by: Mark Kettenis <[email protected]>
|
|
Enable CONFIG_SPL_DM_SERIAL. uart and its pinmux was already
marked with u-boot,dm-spl.
Move preloader_console_init after spl_early_init to make sure driver
model work.
Signed-off-by: Peng Fan <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
Enable CONFIG_DM_SERIAL. uart2 and its pinmux was already
marked with u-boot,dm-spl.
Signed-off-by: Peng Fan <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
FEC_QUIRK_ENET_MAC is defined in the imx-regs.h include file and thus
does not need to be defined in the various board config includes.
Signed-off-by: Tim Harvey <[email protected]>
|
|
The IMX8MP SoC FEC needs to have the FEC_QUIRK_ENET_MAC defined.
Fixes: commit 2395625209cc ("board: gateworks: venice: add imx8mp-venice-gw740x support")
Signed-off-by: Tim Harvey <[email protected]>
|
|
The IMX8M based Venice boards all have device-tree fec nodes that
use proper dt with a phy-handle pointing to a phy with reg assigned
to the proper phy address.
There is no need to keep using the CONFIG_FEC_MXC_PHYADDR hack when
a proper dt is used - remove it.
Signed-off-by: Tim Harvey <[email protected]>
|
|
Introduce helper macro UART_BASE_ADDR(n), which returns Nth UART base
address. Convert all board configurations to this new macro. This is the
first step toward switching CONFIG_MXC_UART_BASE to Kconfig. This is a
clean up, no functional change.
The new macro contains compile-time test to verify N is in suitable
range. The test works such that it multiplies constant N by constant
double-negation of size of a non-empty structure, i.e. it multiplies
constant N by constant 1 in each successful compilation case.
The non-empty structure may contain C11 _Static_assert(), make use of
this and place the kernel variant of static assert in there, so that
it performs the compile-time check for N in the correct range. Note
that it is not possible to directly use static_assert in compound
statements, hence this convoluted construct.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
|
|
Introduce helper macro UART_BASE_ADDR(n), which returns Nth UART base
address. Convert all board configurations to this new macro. This is the
first step toward switching CONFIG_MXC_UART_BASE to Kconfig. This is a
clean up, no functional change.
The new macro contains compile-time test to verify N is in suitable
range. The test works such that it multiplies constant N by constant
double-negation of size of a non-empty structure, i.e. it multiplies
constant N by constant 1 in each successful compilation case.
The non-empty structure may contain C11 _Static_assert(), make use of
this and place the kernel variant of static assert in there, so that
it performs the compile-time check for N in the correct range. Note
that it is not possible to directly use static_assert in compound
statements, hence this convoluted construct.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>
|
|
RNG Hardware error is reported due to incorrect entropy delay
rng self test are run to determine the correct ent_dly.
test is executed with different voltage and temperature to identify the
worst case value for ent_dly. after adding a margin value(1000),
ent_dly should be at least 12000.
Signed-off-by: Gaurav Jain <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
CONFIG_SPL_FS_LOAD_PAYLOAD_NAME is used by set_dfu_alt_info() for string
generation. It doesn't depend on SDHCI because the same file can be stored
to other non volatile memories like qspi.
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/97434e122c6f8f042330b60d3e8de4c31f3e3f93.1652192580.git.michal.simek@amd.com
Link: https://lore.kernel.org/r/718de136c68c9a76fc7b4e536a727f401b05bfb9.1652702625.git.michal.simek@amd.com
|
|
This converts the following to Kconfig:
CONFIG_MTD_CONCAT
Signed-off-by: Chris Packham <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-stm
Add new STM32 MCU boards and Documentation
STM32 programmer improvements
video: support several LTDC HW versions and fix data enable polarity
board: fix stboard error message, consider USB cable connected when boot device is USB
configs: stm32mp1: set console variable for extlinux.conf
configs: stm32mp1: add support for baudrate higher than 115200 for ST-Link
ARM: stm32mp: Fix Silicon version handling and ft_system_setup()
phy: stm32-usbphyc: Add DT phy tuning support
arm: dts: stm32mp15: alignment with v5.18
ram: Conditionally enable ASR
mach-stm32mp: psci: retain MCUDIVR, PLL3CR, PLL4CR, MSSCKSELR across suspend
configs: Use TFTP_TSIZE on DHSOM and STMicroelectronics boards
ARM: stm32: Use default CONFIG_TFTP_BLOCKSIZE on DHSOM
pinctrl: stm32: rework GPIO holes management
|
|
As stm32f46-disco, stm32f769-disco and stm32746g-eval are very similar
except their respective device tree file. These 3 boards uses the same
TARGET_STM32F746_DISCO flag (so same include/configs/stm32f746-disco.h
and same board file board/st/stm32f746-disco/stm32f746-disco.c)
To be able to compile these 3 boards, replace the hard-coded device-tree
name in include/configs/stm32f746-disco.h by CONFIG_DEFAULT_DEVICE_TREE
which is set in each board defconfig file with the correct value.
Signed-off-by: Patrice Chotard <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
|
|
This allows to concatenate spl and u-boot binaries together.
Previously, both binaries has to be flashed separately at the correct
offset (spl at offset 0 and u-boot at offset 0x8000).
With this patch, only one binary is generated (u-boot-with-spl.bin)
and has to be copied in flash at offset 0 using openocd for example
or simply copied in exported mass storage.
Signed-off-by: Patrice Chotard <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
|
|
On STMicroelectronics boards, the UART can reliably go up to
2000000 bauds when connected to the on-board ST-LINK-V2 for STM32MP15
Unfortunately U-Boot will fall back to 115200 unless higher rates are
declared via CONFIG_SYS_BAUDRATE_TABLE.
This patch add the support of higher baudrates on STMicroelectronics
boards with ST-LINK.
Cc: Alexandru Gagniuc <[email protected]>
Signed-off-by: Patrick Delaunay <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
Signed-off-by: Patrice Chotard <[email protected]>
|
|
Set the environment variable "console", used in extlinux.conf file when it
is generated by YOCTO distribution with:
UBOOT_EXTLINUX_CONSOLE ??= "console=${console},${baudrate}"
With these 2 variables, U-Boot give dynamically the used console and
baudrate in the Linux kernel bootargs.
For the STMicroelectronics boards, the used console is ttySTM0.
Signed-off-by: Patrick Delaunay <[email protected]>
Reviewed-by: Patrice Chotard <[email protected]>
Signed-off-by: Patrice Chotard <[email protected]>
|
|
The TPS65219 I2S PMIC features 3 Buck converters and 4 linear regulators,
2 GPOs, 1 GPIO, and 3 multi-function-pin.
This adds the PMIC driver, loading the regulator sub-nodes.
Signed-off-by: Neil Armstrong <[email protected]>
|
|
For CONFIG_DM_SERIAL it is required to increase CONFIG_SYS_MALLOC_F_LEN as
default value is not enough for memory hungry CONFIG_DM_SERIAL code.
Signed-off-by: Pali Rohár <[email protected]>
Tested-by: Merlijn Wajer <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-07-rc3-2
UEFI:
* Fix build errors due to
- using sed with non-standard extension for regular expression
- target architecture not recognized for CROSS_COMPILE=armv7a-*
- CONFIG_EVENT not selected
* add sha384/512 on certificate revocation
Others:
* factor out the user input handling in bootmenu command
|
|
Currently we don't support sha384/512 for the X.509 certificate
in dbx. Moreover if we come across such a hash we skip the check
and approve the image, although the image might needs to be rejected.
Rework the code a bit and fix it by adding an array of structs with the
supported GUIDs, len and literal used in the U-Boot crypto APIs instead
of hardcoding the GUID types.
It's worth noting here that efi_hash_regions() can now be reused from
efi_signature_lookup_digest() and add sha348/512 support there as well
Signed-off-by: Ilias Apalodimas <[email protected]>
|
|
This commit moves the user input handling from cmd/bootmenu.c
to common/menu.c to reuse it from other modules.
Signed-off-by: Masahisa Kojima <[email protected]>
Reviewed-by: Heinrich Schuchardt <[email protected]>
|
|
If a gpt table is corrupted (after a power cut
for example), then the gpt table should repaired.
The function gpt_repair_headers check if at least
one gpt table is valid, and then only write the
corrupted gpt table.
Signed-off-by: Philippe Reynes <[email protected]>
|
|
We currently overflow due to wrong types used internally in rtc_mktime,
on all platforms, and we return a too small type on 32-bit.
One consumer that directly benefits from this is mktime64. Many others
may still store the result in a wrong type.
While at it, drop the redundant cast of mon in rtc_mktime (obsoleted by
714209832db1).
Signed-off-by: Jan Kiszka <[email protected]>
|
|
address in arm64
Currently, in case of arm64 bootloader and U-Boot the stack pointer is
initialized at an offset of NON_SECURE_MSRAM_SIZE from arm64 SPL's text
base address. After jumping to arm64, execution is done out of DDR.
Therefore, having an offset corresponding to the size of MSRAM does not
have any significance.
Instead, initialize the stack pointer after an offset of 4MB from the SPL
text base address. This helps in allocating larger memory for stack.
┌────────────────────┐0x80080000
│ │
│ arm64 SPL │
├────────────────────┤
│ ▲ │
│ │ │
│ STACK │
├────────────────────┤0x80480000
│ Memory for Load │
│ Buffer Allocation │
├────────────────────┤0x80800000
│ │
│ U-Boot Image │
│ │
└────────────────────┘
Signed-off-by: Aswath Govindraju <[email protected]>
|
|
Add clock controller driver for NPCM750
Signed-off-by: Jim Liu <[email protected]>
Signed-off-by: Stanley Chu <[email protected]>
Reviewed-by: Sean Anderson <[email protected]>
|
|
Add basic support for the Nuvoton NPCM750 EVB (Poleg).
Signed-off-by: Jim Liu <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-07-rc2-2
* Test
Unit test for 'bootmenu' command
* UEFI
Preparatory patches for implementing a UEFI boot options based menu
|
|
Add helper to resolve PHY node from it's ofnode via DM MDIO subsystem.
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Ramon Fried <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
This patch enables the Kconfig symbols needed for full ethernet support
on the EBB7304. Also the PHY autonegotiation timeout is increased, as
the default 5 seconds are sometime a bit short. With this, ethernet can
be used on this board. Here an example of a tftp load:
=> tftp ffffffff81000000 big
ethernet-mac-nexus@11800e0000000 Waiting for PHY auto negotiation to complete....... done
Using ethernet-mac-nexus@11800e0000000 device
TFTP from server 192.168.1.5; our IP address is 192.168.1.243
Filename 'big'.
Load address: 0xffffffff81000000
Loading: ################################################## 10 MiB
13.2 MiB/s
done
Bytes transferred = 10485760 (a00000 hex)
Signed-off-by: Stefan Roese <[email protected]>
|
|
This patch moves CONFIG_SYS_INIT_SP_OFFSET to a higher address so that
it does not interfere with larger U-Boot images. This was noticed, while
adding network support to the EBB7304 board.
Signed-off-by: Stefan Roese <[email protected]>
|
|
Add a mask parameter to control the lookup of the PCI region from which
the mapping can be made.
Signed-off-by: Andrew Scull <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
Add mask parameter and reorder length parameter to match the other PCI
address conversion functions. Using PCI_REGION_TYPE as the mask gives
the old behaviour.
It's converted from a macro to an inline function as the length
parameter is now used twice, but should only be calculated once.
Signed-off-by: Andrew Scull <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
When converting addresses, apply a mask to the region flags during
lookup. This allows the caller to specify which flags are important and
which are not, for example to exclude system memory regions.
The behaviour of the function is changed such that they don't
preferentially search for a non-system memory region. However, system
memory regions are added after other regions in decode_regions() leading
to a similar outcome.
Signed-off-by: Andrew Scull <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
Evolve dm_pci_map_bar() to include an offset and length parameter. These
allow a portion of the memory to be mapped and range checks to be
applied.
Passing both the offset and length as zero results in the previous
behaviour and this is used to migrate the previous callers.
Signed-off-by: Andrew Scull <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
When converting between PCI bus and physical addresses, include a length
parameter that can be used to check that the entire range fits within
one of the PCI regions. This prevents an address being returned that
might be only partially valid for the range it is going to be used for.
Where the range check is not wanted, passing a length of 0 will have the
same behaviour as before this change.
Signed-off-by: Andrew Scull <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
The flags parameter of dm_pci_map_bar() is used for PCI region flags
rather than memory mapping flags. Fix the type to match that of the
region flags and stop using the regions flags as memory mapping flags.
Signed-off-by: Andrew Scull <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
