| Age | Commit message (Collapse) | Author |
|---|
|
Prepare v2026.01-rc4
|
|
The 32bit cells of a device-tree property are big-endian. When printing
them via 0x08x we must first convert to the host endianness.
Remove the restriction to 20 bytes length. This would not allow to read an
SHA256 value.
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
The Linux kernel can discover SMBIOS tables through two primary methods:
1. Via EFI tables, when using EFI boot;
2. Via the 'smbios3-entrypoint' property in the /chosen node of the
device tree.
When U-Boot boots a Linux kernel using a non-EFI command ("bootm",
"bootz", or "booti"), the kernel relies on the device tree to detect
the hardware. If SMBIOS tables are available in U-Boot, they should
be passed to the kernel via this device tree property.
This patch modifies boot_fdt_prepare(), to inject the SMBIOSv3 table
address into the device tree if there is a table generated by U-boot.
The "board_fdt_chosen_smbios" is weak in order to leave the possibilty
for specific boards to select custom SMBIOS addresses.
The changes in this patch are added in the context of supporting this
device tree property in linux kernel:
https://lkml.org/lkml/2025/10/24/1393
Device tree schema was updated to include the "smbios3-entrypoint" node
in pull request: https://github.com/devicetree-org/dt-schema/pull/177
Signed-off-by: Adriana Nicolae <[email protected]>
|
|
The location of memory depends on the board. Do not assume memory at fixed
memory locations. Use memalign() instead to allocate a buffer.
Acked-by: Ilias Apalodimas <[email protected]>
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
In fdt_test_chosen() currently we test if DM_RNG is configured.
CONFIG_DM_RNG=y does not imply that a RNG device actually exists.
For instance QEMU may be called with -device virtio-rng-device or not.
The current test framework evicts the virtio RNG device even if QEMU is
called with -device virtio-rng-device.
In the fdt_test_chosen() check if a RNG device exists.
Ignore 'No RNG device' messages.
Acked-by: Ilias Apalodimas <[email protected]>
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
The `fdt apply` sub-command is only available if CONFIG_OF_LIBFDT_OVERLAY
is enabled.
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
The include file <command.h> does not need anything from <env.h>.
Furthermore, include/env.h itself includes other headers which can lead
to longer indirect inclusion paths. To prepare to remove <env.h> from
<command.h> fix all of the places which had relied on this indirect
inclusion to instead include <env.h> directly.
Reviewed-by: Mattijs Korpershoek <[email protected]> # android, bcb
Reviewed-by: Jerome Forissier <[email protected]> # spawn
Signed-off-by: Tom Rini <[email protected]>
|
|
This file is empty now. Remove it and its uses.
Signed-off-by: Simon Glass <[email protected]>
|
|
Use the new suite-runner to run these tests instead.
Signed-off-by: Simon Glass <[email protected]>
|
|
Most test suites have a _test suffix. This is not necessary as there is
also a ut_ prefix.
Drop the suffix so that (with future work) the suite name can be used as
the linker-list name.
Remove the suffix from the pytest regex as well, moving it to the top of
the file, as it is a constant.
Signed-off-by: Simon Glass <[email protected]>
|
|
Use the ut_assert_console_end() function provided, rather than doing it
separately.
Signed-off-by: Simon Glass <[email protected]>
|
|
It is seldom necessary to call this function. Drop its use in the
command tests.
Add a few extra checks to the wget test so that resetting is not
needed.
Signed-off-by: Simon Glass <[email protected]>
|
|
Quite a lot of tests have the same two lines of code at the start. Move
this into the two setup functions to reduce redundancy.
Add a line to check the output from set_working_fdt_addr() since this is
always emitted.
Signed-off-by: Simon Glass <[email protected]>
|
|
Some functions are using asserts but the result of the functions
themselves is not checked. This means that if a test fails, the result
is not noticed until later, which can be confusing to debug.
Add the missing asserts.
Signed-off-by: Simon Glass <[email protected]>
|
|
The _REC suffix doesn't add much. Really what we want to know is whether
the test uses the console, so rename this flag.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Mattijs Korpershoek <[email protected]>
|
|
The UT_TESTF_ macros read as 'unit test test flags' which is not right.
Rename to UTF ('unit test flags').
This has the benefit of being shorter, which helps keep UNIT_TEST()
declarations on a single line.
Give the enum a name and reference it from the UNIT_TEST() macros while
we are here.
Signed-off-by: Simon Glass <[email protected]>
|
|
Tim Harvey <[email protected]> says:
This series will automatically add /chosen/kaslr-seed to the dt if
DM_RNG is enabled
during the boot process.
If RANDOMIZE_BASE is enabled in the Linux kernel instructing it to
randomize the virtual address at which the kernel image is loaded, it
expects entropy to be provided by the bootloader by populating
/chosen/kaslr-seed with a 64-bit value from source of entropy at boot.
If we have DM_RNG enabled populate this value automatically when
fdt_chosen is called. We skip this if ARMV8_SEC_FIRMWARE_SUPPORT
is enabled as its implementation uses a different source of entropy
that is not yet implemented as DM_RNG. We also skip this if
MEASURED_BOOT is enabled as in that case any modifications to the
dt will cause measured boot to fail (although there are many other
places the dt is altered).
As this fdt node is added elsewhere create a library function and
use it to deduplicate code. We will provide a parameter to overwrite
the node if present.
For our automatic injection, we will use the first rng device and
not overwrite if already present with a non-zero value (which may
have been populated by an earlier boot stage). This way if a board
specific ft_board_setup() function wants to customize this behavior
it can call fdt_kaslrseed with a rng device index of its choosing and
set overwrite true.
Note that the kalsrseed command (CMD_KASLRSEED) is likely pointless now
but left in place in case boot scripts exist that rely on this command
existing and returning success. An informational message is printed to
alert users of this command that it is likely no longer needed.
Note that the Kernel's EFI STUB only relies on EFI_RNG_PROTOCOL for
randomization and completely ignores the kaslr-seed for its own
randomness needs (i.e the randomization of the physical placement of
the kernel). It gets weeded out from the DTB that gets handed over via
efi_install_fdt() as it would also mess up the measured boot DTB TPM
measurements as well.
|
|
Now that kaslr-seed is automatically added to the chosen node if DM_RNG
is enabled, adjust the test to expect this.
Take care not to expect kaslr-seed for CONFIG_MEASURED_BOOT and
CONFIG_ARMV8_SEC_FIRMWARE_SUPPORT as we do not add it for those.
Signed-off-by: Tim Harvey <[email protected]>
Cc: Michal Simek <[email protected]>
Cc: Andy Yan <[email protected]>
Cc: Akash Gajjar <[email protected]>
Cc: Ilias Apalodimas <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Patrick Delaunay <[email protected]>
Cc: Patrice Chotard <[email protected]>
Cc: Devarsh Thakkar <[email protected]>
Cc: Heinrich Schuchardt <[email protected]>
Cc: Hugo Villeneuve <[email protected]>
Cc: Marek Vasut <[email protected]>
Cc: Tom Rini <[email protected]>
Cc: Chris Morgan <[email protected]>
|
|
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.
Reported-by: Jonas Karlman <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Remove <common.h> from all "test/" files and when needed add
missing include files directly.
Signed-off-by: Tom Rini <[email protected]>
|
|
The error that this test checks for is only shown on sandbox. For real
boards, there is normally no error. Add a special case to handle this.
Signed-off-by: Simon Glass <[email protected]>
|
|
Drop the map_to_sysmem() copy paste error. No functional change.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
64597346 "fdt: Add -q option to fdt addr for distro_bootcmd" introduced
the -q option for fdt addr, which sets the current working fdt address
without printing any output.
baf41410 "fdt: Show a message when the working FDT changes" made the
utility function set_working_fdt_addr (in cmd/fdt.c) output a message
on each invocation, even if called via fdt addr -q, in which case its
output is now slightly noisier.
To fix this, split out set_working_fdt_addr into set_working_fdt_addr
plus the static function set_working_fdt_addr_quiet.
set_working_fdt_addr_quiet can be called by "quiet" fdt cmd logic and
set_working_fdt_addr is exported (as before) to other boot logic. The
latter calls the former.
Remove the assertion from the fdt addr test case when calling with the
-q argument.
Signed-off-by: Peter Hoyes <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Fix warnings both for 32bit and 64bit architecture after adding
printf-like attribute format for run_commandf():
warning: format ‘%x’ expects argument of type ‘unsigned int’, but
argument 2 has type ‘ulong {aka long unsigned int}’ [-Wformat=]
ret = run_commandf("fdt addr -c %08x", addr);
^
Signed-off-by: Evgeny Bachinin <[email protected]>
Cc: Marek Vasut <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
[trini: Fixup testcases added since patch was posted]
Signed-off-by: Tom Rini <[email protected]>
|
|
Add 'fdt chosen' test which works as follows:
- Create basic DT, map it to sysmem
- Apply DTO which adds single property via fragment (without address spec)
- Apply DTO which adds more properties (string, u32, empty) and a subnode,
with phandle via frament@0 and thus tests /__symbols__ node
- Apply DTO which modifies property of the previous DTO via phandle and thus
tests the /__fixups__ node
- Print modified DT, verify it contains updates from DTOs
The test case can be triggered using:
"
./u-boot -Dc 'ut fdt'
"
To dump the full output from commands used during test, add '-v' flag.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Add 'fdt chosen' test which works as follows:
- Create basic DT, map it to sysmem
- Print /chosen node, verify it is nonexistent
- Create chosen node
- Print /chosen node, verify it contains only version
- Create /chosen node with initrd entries
- Print /chosen node, verify it contains version and initrd entries
The test case can be triggered using:
"
./u-boot -Dc 'ut fdt'
"
To dump the full output from commands used during test, add '-v' flag.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Add 'fdt rsvmem' test which works as follows:
- Create custom FDT with single reserved memory (rsvmem) entry, map it to sysmem
- Add new rsvmem entry
- Delete existing older rsvmem entry
- Add new rsvmem entry again
- Always print the rsvmem list and validate it
The test case can be triggered using:
"
./u-boot -Dc 'ut fdt'
"
To dump the full output from commands used during test, add '-v' flag.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Add 'fdt memory' test which works as follows:
- Create custom FDT with /memory node, with select #*cells, map it to sysmem
- Perform memory fixup
- Read back the /memory node and validate its content
The test case can be triggered using:
"
./u-boot -Dc 'ut fdt'
"
To dump the full output from commands used during test, add '-v' flag.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Add 'fdt header' test which works as follows:
- Create basic FDT, map it to sysmem
- Print the FDT header
- Get all members of the FDT header into variable and
verify the variables contain correct data
The test case can be triggered using:
"
./u-boot -Dc 'ut fdt'
"
To dump the full output from commands used during test, add '-v' flag.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Merged in test: cmd: fdt: Drop unused fdt_test_header_get() fdt parameter:
Signed-off-by: Simon Glass <[email protected]>
|
|
Add 'fdt print' and 'fdt list' test which works as follows:
- Create fuller FDT, map it to sysmem
- Print the entire FDT, parts of the FDT and select properties
- Compare output from the print or list
The test case can be triggered using:
"
./u-boot -Dc 'ut fdt'
"
To dump the full output from commands used during test, add '-v' flag.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Drop no longer needed { } around ut_assert*() functions in FDT test.
No functional change.
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
|
|
Add list of missing tests for the 'fdt' command, currently
the missing sandbox tests are only 'fdt boardsetup' and
'fdt checksign' .
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Add 'fdt bootcpu' test which works as follows:
- Create basic FDT, map it to sysmem
- Print the FDT bootcpu
- Set the FDT bootcpu and read the value back using 'fdt header get'
- Perform the previous step twice to validate bootcpu overwrite
The test case can be triggered using:
"
./u-boot -Dc 'ut fdt'
"
To dump the full output from commands used during test, add '-v' flag.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Add 'fdt rm' test which works as follows:
- Create fuller FDT, map it to sysmem
- Selectively delete nodes or properties by both path and aliases
- Verify created nodes or properties using fdt print command
The test case can be triggered using:
"
./u-boot -Dc 'ut fdt'
"
To dump the full output from commands used during test, add '-v' flag.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Add 'fdt mknode' test which works as follows:
- Create fuller FDT, map it to sysmem
- Create node either in / or subnode
- Attempt to create node over existing node, which fails
- Attempt to create subnodes in non-existing nodes or aliases
- Verify created nodes using fdt list command
The test case can be triggered using:
"
./u-boot -Dc 'ut fdt'
"
To dump the full output from commands used during test, add '-v' flag.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Add 'fdt set' test which works as follows:
- Create fuller FDT, map it to sysmem
- Set either existing property to overwrite it, or new property
- Test setting both single properties as well as string and integer arrays
- Test setting to non-existent nodes and aliases
- Verify set values using 'fdt get value'
The test case can be triggered using:
"
./u-boot -Dc 'ut fdt'
"
To dump the full output from commands used during test, add '-v' flag.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Add 'fdt get size' test which works as follows:
- Create fuller FDT, map it to sysmem
- Get size of various properties
- Get node count of available nodes
- Test non-existent nodes and properties
The test case can be triggered using:
"
./u-boot -Dc 'ut fdt'
"
To dump the full output from commands used during test, add '-v' flag.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Add 'fdt get addr' test which works as follows:
- Create fuller FDT, map it to sysmem
- Get address of various properties
- Compare addresses calculated by UT and fdt command
This test is special in that it has to go through gruesome remapping scheme
where the test calculates:
- pointer offsets of the generated FDT root and the property being tested
- map_sysmem() result of environment variable "fdtaddr" and the one set
by the test matching address of property being tested
- difference between the later and the former, to obtain offset of the
DT property from start of DT
The offsets must match in both the UT and the tested U-Boot, if they do
not, the test fails.
The test case can be triggered using:
"
./u-boot -Dc 'ut fdt'
"
To dump the full output from commands used during test, add '-v' flag.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Add 'fdt get name' test which works as follows:
- Create fuller FDT, map it to sysmem
- Get name of / node 0, 1 and /clk-test node 0
- Compare output and validate the node name
- Get name of / node 2 and /clk-test node 1
- Compare output and validate the node is not present
- Get name of / node -1 and /clk-test node -1
- Compare output and validate the node name equals node 0 name
- Check nonexistent node, verify the command errors out
The test case can be triggered using:
"
./u-boot -Dc 'ut fdt'
"
To dump the full output from commands used during test, add '-v' flag.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Add 'fdt resize' test which works as follows:
- Create simple FDT with extra size 0, map it to sysmem
- 'resize' the FDT by 0x2000 bytes
- Verify the new space has been added to the FDT
The test case can be triggered using:
"
./u-boot -Dc 'ut fdt'
"
To dump the full output from commands used during test, add '-v' flag.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Add 'fdt move' test which works as follows:
- Create simple FDT, map it to sysmem
- 'move' the FDT into new zeroed out sysmem location
- Verify newly active FDT is in the new location
- Compare both locations
The test case can be triggered using:
"
./u-boot -Dc 'ut fdt'
"
To dump the full output from commands used during test, add '-v' flag.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
The 'fdt get value' subcommand now supports extraction of integer value
from integer arrays, add test for it, including a test for special case
unindexed integer array read, which is handled as hash and treated as a
long string instead of integer.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
The 'fdt' command help contains the following note:
"
Dereference aliases by omitting the leading '/', e.g. fdt print ethernet0.
"
Add test for it.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Implement function to generate internal test DT fragment and switch
the 'fdt get value' test to this instead of depending on the sandbox
DT. Rename clk-test node to test-node node. This FDT fragment will be
reused by other tests. No functional change.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
The 'fdt get' command has a 'get value' subcommand, rename the fdt_test_get()
to fdt_test_get_value() to avoid confusion about what it is testing. There is
currently no get 'get name', 'get addr', 'get size' subcommand test.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
The 'fdt' command has a 'resize' subcommand, rename the fdt_test_resize()
to fdt_test_addr_resize() to avoid confusion about what it is testing.
There is currently no resize test.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Add test case for 'fdt get value' sub command.
The test case can be triggered using:
"
./u-boot -d u-boot.dtb -c 'ut fdt'
"
Acked-by: Heinrich Schuchardt <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
|
|
The working FDT is the one which comes from the OS and is fixed up by
U-Boot. When the bootm command runs, it sets up the working FDT to be the
one it is about to pass to the OS, so that fixups can happen.
This seems like an important step, so add a message indicating that the
working FDT has changed. This is shown during the running of the bootm
command.
Signed-off-by: Simon Glass <[email protected]>
|
|
Add a basic test of the 'fdt addr' command, to kick things off.
This includes a new convenience function to run a command from a printf()
string.
Signed-off-by: Simon Glass <[email protected]>
|
