| Age | Commit message (Collapse) | Author |
|---|
|
Add a SPL test for the NAND load method. We use some different functions to
do the writing from the main test since things like nand_write_skip_bad
aren't available in SPL.
We disable BBT scanning, since scan_bbt is only populated when not in SPL.
We use nand_spl_loaders.c as it seems to be common to at least a few boards
already. However, we do not use nand_spl_simple.c because it would require
us to implement cmd_ctrl. The various nand load functions are adapted from
omap_gpmc. However, they have been modified for simplicity/correctness.
Signed-off-by: Sean Anderson <[email protected]>
|
|
Add test for the SPI load method. This one is pretty straightforward. We
can't enable FIT_EXTERNAL with LOAD_FIT_FULL because spl_spi_load_image
doesn't know the total image size and has to guess from fdt_totalsize. This
doesn't include external data, so loading it will fail.
Signed-off-by: Sean Anderson <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Add a test for the NOR load method. Since NOR is memory-mapped we can
substitute a buffer instead. The only major complication is testing LZMA
decompression. It's too complex to implement LZMA compression in a test, and we
have no in-tree compressor, so we just include some pre-compressed data. This
data was generated through something like
generate_data(plain, plain_size, "lzma")
cat plain.dat | lzma | hexdump -C
and was cleaned up further in my editor.
Signed-off-by: Sean Anderson <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Add a test for loading U-Boot over TFTP. As with other sandbox net
routines, we need to initialize our packets manually since things like
net_set_ether and net_set_udp_header always use "our" addresses. We use
BOOTP instead of DHCP, since DHCP has a tag/length-based format which is
harder to parse. Our TFTP implementation doesn't define as many constants
as I'd like, so I create some here. Note that the TFTP block size is
one-based, but offsets are zero-based.
In order to avoid address errors, we need to set up/define some additional
address information settings. dram_init_banksize would be a good candidate
for settig up bi_dram, but it gets called too late in board_init_r.
Signed-off-by: Sean Anderson <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Add some functions for creating fat/ext2 filesystems with a single file and
a test for them. Filesystems require block devices, and it is easiest to
just use MMC for this. To get an MMC, we must also pull in the test device
tree. SPL_TIMER is necessary for SPL_MMC, perhaps because it uses a timeout.
Signed-off-by: Sean Anderson <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
In order to make adding new spl unit tests easier, especially when they may
have many dependencies, add some Kconfigs for the existing image test.
Split it into the parts which are generic (such as callbacks) and the
test-specific parts.
Signed-off-by: Sean Anderson <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
As an example of an SPL test, add a new test for loading a FIT within
SPL. This runs on sandbox_spl. For this to work, the text base is adjusted
so that there is plenty of space available.
While we are here, document struct spl_load_info properly, since this is
currently ambiguous.
This test only verifies the logic path. It does not actually check that
the image is loaded correctly. It is not possible for sandbox's SPL to
actually run u-boot.img since it currently includes u-boot.bin rather than
u-boot. Further work could expand the test in that direction.
The need for this was noted at:
http://patchwork.ozlabs.org/project/uboot/patch/[email protected]/
Signed-off-by: Simon Glass <[email protected]>
|
