1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
|
.. SPDX-License-Identifier: GPL-2.0+
U-Boot for the LG Optimus 2X P990
=================================
``DISCLAMER!`` Moving your device to use U-Boot assumes replacement of the
vendor bootloader. Vendor Android firmwares will no longer be able to run on
the device. This replacement IS reversible if you have backups.
Quick Start
-----------
- Build U-Boot
- Process U-Boot
- Flashing U-Boot into the eMMC
- Boot
- Self Upgrading
Build U-Boot
------------
.. code-block:: bash
$ export CROSS_COMPILE=arm-none-eabi-
$ make star_defconfig
$ make
After the build succeeds, you will obtain the final ``u-boot-dtb-tegra.bin``
image, ready for further processing.
Process U-Boot
--------------
``DISCLAMER!`` All questions related to the re-crypt work should be asked
in re-crypt repo issues. NOT HERE!
re-crypt is a tool that processes the ``u-boot-dtb-tegra.bin`` binary into form
usable by device. This process is required only on the first installation or to
recover the device in case of a failed update.
.. code-block:: bash
$ git clone https://gitlab.com/grate-driver/re-crypt.git
$ cd re-crypt # place your u-boot-dtb-tegra.bin here
$ ./re-crypt.py --dev star --split
The script will produce ``bct.img`` and ``ebt.img`` ready to flash.
Flashing U-Boot into the eMMC
-----------------------------
``DISCLAMER!`` All questions related to fusee-tools should be asked in the proper
place. NOT HERE! Flashing U-Boot will erase all eMMC, so make a backup before!
Permanent installation can be performed by pre-loading just built U-Boot into RAM.
Bct and bootloader will end up in boot0 and boot1 partitions of eMMC.
You have to clone and prepare fusee-tools from here: https://gitlab.com/grate-driver/fusee-tools
according to fusee-tools README to continue. Additionally you must install ``tegrarcm``.
Bootloader preloading is performed to device in APX/RCM mode connected to host
PC. This mode can be entered by holding ``power`` and both volume buttons on
turned off phone connected to the host PC. Host PC should detect APX USB device
in ``lsusb``.
U-Boot pre-loaded into RAM acts the same as when it was booted "cold". Currently
U-Boot supports bootmenu entry fastboot, which allows to write a processed copy
of U-Boot permanently into eMMC. This is how U-Boot can be preloaded using
fusee-tools:
.. code-block:: bash
$ tegrarcm --bct ./bct/star.bct --bootloader u-boot-dtb-tegra.bin --loadaddr 0x108000
While pre-loading U-Boot, hold the ``volume down`` button which will trigger
the bootmenu. There, select ``fastboot`` using the volume and power buttons.
After, on host PC, do:
.. code-block:: bash
$ fastboot flash 0.1 bct.img
$ fastboot flash 0.2 ebt.img
$ fastboot reboot
Device will reboot.
Boot
----
To boot Linux, U-Boot will look for an ``extlinux.conf`` on MicroSD and then on
eMMC. Additionally, if the Volume Down button is pressed while booting, the
device will enter bootmenu. Bootmenu contains entries to mount MicroSD and eMMC
as mass storage, fastboot, reboot, reboot RCM, poweroff, enter U-Boot console
and update bootloader (check the next chapter).
Flashing ``bct.img`` and ``ebt.img`` eliminates vendor restrictions on eMMC and
allows the user to use/partition it in any way the user desires.
Self Upgrading
--------------
Place your ``u-boot-dtb-tegra.bin`` on the first partition of the MicroSD card
and insert it into the device. Enter bootmenu, choose update the bootloader
option with the Power button and U-Boot should update itself. Once the process
is completed, U-Boot will ask to press any button to reboot.
|
