| Age | Commit message (Collapse) | Author |
|---|
|
Add RPMI MPXY proxy driver for LOGGING service group so that
S-mode can leverage LOGGING service group implemented by the
platform microcontroller.
Reviewed-by: Rahul Pathak <[email protected]>
Signed-off-by: Subrahmanya Lingappa <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Litex SoC controller supports reboot function by toggling the first
bit of the ctrl register. Add a reset driver so other software can
use it.
Signed-off-by: Inochi Amaoto <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
The SpacemiT P1 is a PMIC commonly found with SpacemiT CPU like K1. Add
a reset driver for it.
Signed-off-by: Aurelien Jarno <[email protected]>
Tested-by: Anand Moon <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Add a simple SpacemiT I2C driver for basic byte transfers over the I2C
bus, prioritizing simplicity over performance. The driver operates in
PIO mode and does not use interrupts, FIFO, or DMA.
The controller is reset at the start of each transaction to ensure a
known initial state, regardless of prior configuration by the kernel.
This also avoids the need for additional error recovery code.
This will be used for communication with onboard PMIC to reset and
power-off the board.
Signed-off-by: Aurelien Jarno <[email protected]>
Tested-by: Anand Moon <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Add the Tenstorrent Atlantis as a generic-platform. This initial support
enables the single_fw_region option, and verifies and prints HART PMA
CSR configuration.
Signed-off-by: Nicholas Piggin <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Add necessary infra for implementing RPMI Management Mode
service group on platform microcontroller.
Co-authored-by: Sunil V L <[email protected]>
Signed-off-by: Ranbir Singh <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Add initial platform support for SiFive development platforms
with the "sifive-dev" compatible string.
Reviewed-by: Greentime Hu <[email protected]>
Reviewed-by: Zong Li <[email protected]>
Signed-off-by: Yu-Chien Peter Lin <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Refactor MIPS P8700 support, convert P8700 into a "CPU" and add
2 platforms using this CPU:
- "boston" - FPGA platform developed by MIPS
- "eyeq7h" - automotive platform by Mobileye
Signed-off-by: Vladimir Kondratiev <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Altera provides a JTAG UART core that provides virtual UART over JTAG
and can coexist with their virtual JTAG. [1] This core has already been
supported by Linux and the programming interface has always been stable.
Add support for it to OpenSBI to ease JTAG prototype bringing up.
The driver follows the device tree binding in mainline Linux. [2]
[1] https://docs.altera.com/r/docs/683130/25.3/embedded-peripherals-ip-user-guide/jtag-uart-core
[2] https://github.com/torvalds/linux/blob/v6.19-rc1/Documentation/devicetree/bindings/serial/altr%2Cjuart-1.0.yaml
Signed-off-by: Icenowy Zheng <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Implement a system-wide suspend driver for the Andes AE350 platform.
This driver supports Andes-specific deep sleep (suspend to RAM) and
light sleep (suspend to standby) functionalities via the ATCSMU.
The major differences between deep sleep and light sleep are:
- Power Domain and Resume Path: Deep sleep powers down the core domain.
Consequently, harts waking from deep sleep resume from the reset
vector. Light sleep utilizes clock gating to the core domain; harts
maintain state and resume execution at the instruction immediately
following the WFI instruction.
- Primary Hart Wakeup: In both modes, the primary hart is woken by
UART or RTC alarm interrupts. In deep sleep, the primary hart is
additionally responsible for re-enabling the Last Level Cache (LLC)
and restoring Andes-specific CSRs.
- Secondary Hart Wakeup: In light sleep, secondary harts are woken
by an IPI sent from the primary hart. In deep sleep, they are
woken by an ATCSMU hardware wake-up command. Furthermore,
secondary harts must restore Andes-specific CSRs when returning
from deep sleep.
Signed-off-by: Ben Zong-You Xie <[email protected]>
Signed-off-by: Leo Yu-Chi Liang <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Introduce a FDT-based driver for the Andes Last Level Cache (LLC)
controller to support cache maintenance operations.
Signed-off-by: Ben Zong-You Xie <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Refactor ATCSMU (System Management Unit) support by moving it from a
system utility into a dedicated FDT-based HSM driver.
Key changes include:
- Moving the functions in lib/utils/sys/atcsmu.c into the new HSM driver
- Moving hart start and stop operations on AE350 platform into the new
HSM driver
- Converting the assembly-based functions in sleep.S to C code for the
readability
- Updating the ATCWDT200 driver
Signed-off-by: Ben Zong-You Xie <[email protected]>
Signed-off-by: Leo Yu-Chi Liang <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Initial platform support for ESWIN Computing EIC7700 based on public SoC
datasheet[1] and tested on HiFive Premier P550. Vendor U-boot/Linux boots
fine, and I've tested Geekbench 6.5.0 Preview and got scores on par with
the vendor OpenSBI. System shutdown/reboot for HiFive Premier P550 and
other boards will be implemented in subsequent commits. At this point,
only SoC-level warm reset is implemented.
The files and functions are intentionally named as eic770x in many places
for future enhancements to support the 2 die version of the same SoC,
namely EIC7702, seen on DC-ROMA AI PC FML13V03 [2]. This patch set only
deals with the single die version, and the assumption is we can be either
die with id=0 or id=1, but there's only a single die in the system, or we
are only using a single die out of 2. However, the way the SoC handles 2-
die greatly affects how we configure it in a 1-die setup. EIC770X address
map has die 0/1 memory regions interleaved (see comments in eic770x.c).
If only 1 die is connected or active, it creates holes in the address map
for those regions corresponding to the remote die. When speculative-
execution or HW prefetcher touches data-cacheable regions that happen to
fall into those holes, it can trigger bus error. Specifically:
- Remote (non-existent) die L3 zero device
- Remote (non-existent) die cached memory region
- Other holes in Memory Port
To make matters worse, EIC770X doesn't have cache coherent DMA, and due
to the fact that the P550 core lacks Svpbmt, the SoC maps main memory
twice as different regions, so it can bypass cache and fetch the data
directly from memory. In address space, we have two memory regions, one
as cached, the other as uncached. Thus, we also need an extra PMP entry
to protect OpenSBI blob from the uncached window. To do this, platform
code requires single_fw_region, otherwise, we'll run out of PMP entries.
EIC770X also have several feature disable/enable CSRs accessible in M
mode. By default many core features such as speculation and HW prefetch
are disabled, and M mode software is responsible of enabling. Hence,
introduce 4 new build time tunable parameters to Kconfig, which reflects
the values get updated to those CSRs:
- ESWIN_EIC770X_FEAT0_CFG
- ESWIN_EIC770X_FEAT1_CFG
- ESWIN_EIC770X_L1_HWPF_CFG
- ESWIN_EIC770X_L2_HWPF_CFG
The default values are somewhat optimal for generic workloads. They are
dumped when running SiFive's vendor OpenSBI, and in addition, with my
own tuning to address the perf regression reported by drmpeg [3]
To build the firmware+u-boot blob, Use the following, and docs [4] for
testing it with UART boot without flashing:
make FW_TEXT_START=0x80000000 \
FW_PAYLOAD_OFFSET=0x200000 \
FW_PAYLOAD_PATH=u-boot-nodtb.bin \
FW_PAYLOAD_FDT_ADDR=0xf8000000 \
FW_FDT_PATH=u-boot.dtb
[1] https://github.com/eswincomputing/EIC7700X-SoC-Technical-Reference-Manual
[2] https://github.com/geerlingguy/sbc-reviews/issues/82
[3] https://forums.sifive.com/t/low-1-core-stream-bandwidth/7274/15
[4] https://github.com/ganboing/EIC770x-Docs/blob/main/p550/bootchain/UART-Boot.md
Signed-off-by: Bo Gan <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Add support for SiFive Extensible Cache (EC) controller with multi-slice
architecture. The driver implements cache maintenance operations through
MMIO register interface.
Co-developed-by: Vincent Chen <[email protected]>
Signed-off-by: Vincent Chen <[email protected]>
Co-developed-by: Samuel Holland <[email protected]>
Signed-off-by: Samuel Holland <[email protected]>
Co-developed-by: Yong-Xuan Wang <[email protected]>
Signed-off-by: Yong-Xuan Wang <[email protected]>
Signed-off-by: Nick Hu <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
SiFive Private L2(PL2) cache is a private cache owned by each hart. Add
this driver to support private cache flush operations via the MMIO
registers.
Co-developed-by: Eric Lin <[email protected]>
Signed-off-by: Eric Lin <[email protected]>
Co-developed-by: Zong Li <[email protected]>
Signed-off-by: Zong Li <[email protected]>
Co-developed-by: Vincent Chen <[email protected]>
Signed-off-by: Vincent Chen <[email protected]>
Co-developed-by: Samuel Holland <[email protected]>
Signed-off-by: Samuel Holland <[email protected]>
Signed-off-by: Nick Hu <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
The Ariane framework has a generic PMU that is not used by OpenSBI.
Due to OpenSBI’s build system we cannot directly reuse the generic
platform functions, so move the Ariane platform to generic. Also due
to the generic platform is where new features are added.
Signed-off-by: Manuel Hernández Méndez <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Add MPXY RPMI mailbox driver for performance.
Signed-off-by: Joshua Yeong <[email protected]>
Reviewed-by: Rahul Pathak <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Add MPXY RPMI mailbox driver for device power.
Signed-off-by: Joshua Yeong <[email protected]>
Reviewed-by: Rahul Pathak <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Add voltage service group for RPMI/MPXY support
Signed-off-by: Joshua Yeong <[email protected]>
Reviewed-by: Rahul Pathak <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
The SiFive SMC0 controls the clock and power domain of the core complex
on the SiFive platform. The core complex enters the low power state
after the secondary cores enter the tile power gating and last core
execute the `CEASE` instruction with the corresponding SMC0
configurations. The devices that inside both tile power domain and core
complex power domain will be off, including caches and timer. Therefore
we need to flush the last level cache before entering the core complex
power gating and update the timer after waking up.
Reviewed-by: Cyan Yang <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Signed-off-by: Nick Hu <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
The SiFive TMC0 controls the tile power domains on SiFive platform. The
CPU enters the low power state via the `CEASE` instruction after
configuring the TMC0. Any devices that inside the tile power domain will
be power gated, including the private cache. Therefore flushing the
private cache before entering the low power state.
Co-developed-by: Vincent Chen <[email protected]>
Signed-off-by: Vincent Chen <[email protected]>
Reviewed-by: Cyan Yang <[email protected]>
Signed-off-by: Nick Hu <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
SiFive Composable cache is a L3 share cache of the core complex. Add this
driver to support the share cache maintenance operations via the MMIO
registers.
Co-developed-by: Samuel Holland <[email protected]>
Signed-off-by: Samuel Holland <[email protected]>
Signed-off-by: Vincent Chen <[email protected]>
Co-developed-by: Nick Hu <[email protected]>
Signed-off-by: Nick Hu <[email protected]>
Reviewed-by: Samuel Holland <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Add the FDT cache library so we can build up the cache topology via the
'next-level-cache' DT property.
Co-developed-by: Vincent Chen <[email protected]>
Signed-off-by: Vincent Chen <[email protected]>
Co-developed-by: Andy Chiu <[email protected]>
Signed-off-by: Andy Chiu <[email protected]>
Signed-off-by: Nick Hu <[email protected]>
Reviewed-by: Samuel Holland <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Enable CONFIG_PLATFORM_SPACEMIT_K1 in the defconfig for SpacemiT K1 SoC.
Co-authored-by: Troy Mitchell <[email protected]>
Signed-off-by: Troy Mitchell <[email protected]>
Signed-off-by: Xianbin Zhu <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Extend generic platform to support Andes QiLai SoC.
Signed-off-by: Ben Zong-You Xie <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
The OpenPiton framework has a generic PMU that is not used by OpenSBI.
Due to OpenSBI’s build system we cannot directly reuse the generic
platform functions, so move the OpenPiton platform to generic. Also due
to the generic platform is where new features are added.
Signed-off-by: Manuel Hernández Méndez <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Extend generic platform to support MIPS P8700.
Signed-off-by: Chao-ying Fu <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
The supervisor software can directly receive most of the system MSIs
except P2A doorbell and MSIs preferred to be handled in M-mode.
Add MPXY RPMI mailbox client driver for the System MSI service group.
Signed-off-by: Anup Patel <[email protected]>
|
|
Instead of having one common FDT MPXY RPMI mailbox client drivers
for various RPMI service groups, split this driver into two parts:
1) Common MPXY RPMI mailbox client library
2) MPXY driver for RPMI clock service group
The above split enables having a separate MPXY driver for each
RPMI clock service group and #1 (above) will allow code sharing
between various MPXY RPMI drivers.
Signed-off-by: Anup Patel <[email protected]>
|
|
Add a generic RPMI mailbox client driver which provides a MPXY channel.
Initially, this driver only supports RPMI clock service group but can
be extended to support multiple RPMI service groups.
Signed-off-by: Rahul Pathak <[email protected]>
Co-developed-by: Anup Patel <[email protected]>
Signed-off-by: Anup Patel <[email protected]>
|
|
The generic platform can have multiple MPXY drivers so add a simple
FDT based MPXY driver framework.
Signed-off-by: Anup Patel <[email protected]>
|
|
Add RPMI based driver for CPPC register read, write and probe.
Signed-off-by: Subrahmanya Lingappa <[email protected]>
Co-developed-by: Rahul Pathak <[email protected]>
Signed-off-by: Rahul Pathak <[email protected]>
Co-developed-by: Sunil V L <[email protected]>
Signed-off-by: Sunil V L <[email protected]>
Signed-off-by: Anup Patel <[email protected]>
|
|
The generic platform can have multiple CPPC drivers so add a simple
FDT based CPPC driver framework.
Signed-off-by: Anup Patel <[email protected]>
|
|
The RPMI HSM service group provides set of routine to query and control
power states of a Hart. Add RPMI based Hart State Management (HSM) driver.
Signed-off-by: Subrahmanya Lingappa <[email protected]>
Signed-off-by: Anup Patel <[email protected]>
|
|
The generic platform can have multiple HSM drivers so add a simple
FDT based HSM driver framework.
Signed-off-by: Anup Patel <[email protected]>
|
|
Add RPMI based system suspend driver.
To test this, execute the follwoing in Linux:
$ echo mem > /sys/power/state
To wake up, execute the following command on qemu monitor terminal:
(qemu) system_wakeup
Signed-off-by: Subrahmanya Lingappa <[email protected]>
Signed-off-by: Anup Patel <[email protected]>
|
|
The generic platform can have multiple system suspend drivers so add a
simple FDT based system suspend driver framework.
Signed-off-by: Anup Patel <[email protected]>
|
|
Add RPMI based driver for system reset and enable it in the generic
platform defconfig
Signed-off-by: Rahul Pathak <[email protected]>
Signed-off-by: Anup Patel <[email protected]>
|
|
The RISC-V Platform Management Interface (RPMI) defines a messaging protocol
and shared memory based transport for bi-directional communication with an
on-chip or external microcontroller.
To support RPMI in OpenSBI, add:
1) The RPMI messaging protocol defines and helper macros
2) A FDT mailbox driver for the RPMI shared memory transport
Signed-off-by: Rahul Pathak <[email protected]>
Co-developed-by: Subrahmanya Lingappa <[email protected]>
Signed-off-by: Subrahmanya Lingappa <[email protected]>
Co-developed-by: Anup Patel <[email protected]>
Signed-off-by: Anup Patel <[email protected]>
|
|
SG2042 uses an onboard MCU to provide reset function.
Add reset driver to support this onboard MCU.
Signed-off-by: Inochi Amaoto <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
|
|
Add Sophgo sg2042 soc support
Signed-off-by: Inochi Amaoto <[email protected]>
Reviewed-by: Guo Ren <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
|
|
In the past, we used fdt_reset_thead to help customers with prototype
verification. However, with the emergence of the Big-little SoC system,
it can no longer meet the demand. Therefore, we use zero_stage_boot
instead of fdt_reset_thead. It cleans up the opensbi code and ends the
disputation of reset_sample's dts.
This patch removes the fdt_reset_thead component and updates the related
doc.
Signed-off-by: Guo Ren <[email protected]>
Signed-off-by: Guo Ren <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
|
|
The TLB entries remain functional all the time once added in T-HEAD th1520
and Sophgo sg2042 (even if the MMU is then disabled afterwards). If there
are some stale TLB entries that contains the address of SBI, it will cause
unexpected memory access and issue a illegal instruction error. To avoid
this, a TLB flush is needed to drop these TLB entries before any memory
access in the trap handler.
To handle this workaroud, add a custom trap handler with executing TLB flush
first in the T-HEAD platform to fix affected socs.
Signed-off-by: Inochi Amaoto <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
|
|
The functionality of SiFive Test reset driver is easily available
through Syscon reset driver so let us remove the SiFive Test driver.
Signed-off-by: Anup Patel <[email protected]>
|
|
Let us have common FDT based reset driver for syscon reboot and
poweroff. The device tree bindings for syscon reboot and poweroff
are already available in the Linux kernel sources.
Signed-off-by: Anup Patel <[email protected]>
Reviewed-by: Xiang W <[email protected]>
|
|
Let us add a simple FDT based system regmap driver which follows the
device tree bindings already defined in the Linux kernel.
Signed-off-by: Anup Patel <[email protected]>
Reviewed-by: Xiang W <[email protected]>
|
|
We add a simple FDT based regmap framework which is built on top of
generic regmap library. The phandle of FDT regmap DT node is treated
as unique regmap ID. The FDT based regmap drivers will be probed
on-demand from fdt_regmap_get_by_phandle() and fdt_regmap_get()
called by the regmap client drivers.
Signed-off-by: Anup Patel <[email protected]>
Reviewed-by: Xiang W <[email protected]>
|
|
We add generic regmap access library which is independent of
hardware description format (FDT or ACPI). The OpenSBI platform
support or regmap drivers can register regmap instances which
can be discovered by different regmap clients based on the
unique ID of regmap instances.
Signed-off-by: Anup Patel <[email protected]>
Reviewed-by: Xiang W <[email protected]>
|
|
Add a driver for the Synopsys DesignWare APB GPIO IP block found in many
SoCs.
Signed-off-by: Ben Dooks <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
|
|
add reboot and poweroff support. The whole reboot and shutdown
pm op includes shutdown jh7110 pmu device power domain
and access on board pmic register through I2C.
Signed-off-by: Minda Chen <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
|
